Operation - DeWalt DWC410 Original Instructions Manual

EngLIsh
Water Valve Assembly (Fig. A)

WARNING: Test PRCD before each use:
1 . Plug PRCD into power outlet. Indicator should
turn red.
2 . Press test button. Red indicator should disappear.
3 . Press reset button for use. Do not use if above
test fails.

WARNING: Check hose and water kit before each use. Do
not use if hose or water kit is damaged.

CAUTION: Do not connect to water supply more than
6 bar.
If the maximum pressure of the water supply system is above
6 bar a pressure reducing valve must be added between the
tool and the water supply outlet.
1. Never use the saw over head. When using water, limit
cutting to the horizontal position to reduce the risk of water
entering the tool.
2. Prior to using the tool with the water valve assembly,
7
inspect water tubing
Replace with identical replacement parts if a potential
weakened or damaged area is found. Check connections
8
at the tool inlet , water valve and adapter
If the connection is loose or the tubing is relaxed around
barbs, disconnect tubing, trim tubing back approximately
25.4 mm, then reconnect tubing. Ensure that tubing is
pushed all the way past the barb(s). Check to ensure
tight connection.
Use of Extension Cords
• Always plug extension cord into a PRCD receptacle.
• Use only extension cords that are intended for outdoor use.
These extension cords are identified by a marking "Acceptable
for use with outdoor appliance; store indoors while not in use."
• Use only extension cords having an electrical rating not less
than the rating of the product.
• Do not use damaged extension cords. Examine extension cord
before using and replace if damaged.
• Do not abuse extension cords and do not yank on any cord
to disconnect.
Motor
Be sure your power supply agrees with the nameplate marking.
Voltage decrease of more than 10% will cause loss of power and
overheating. All D WALT tools are factory tested; if this tool does
e
not operate, check the power supply.
• Keep cord away from heat and sharp edges.
• Always disconnect the extension cord from the receptacle
before disconnecting the product from the extension cord.

OPERATION

Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.
24
for holes cracks or other damage.
12
for leaks.

WARNING: Use the appropriate blade. Do not use
cracked, damaged or excessively worn blades. Do not use
to cut wood or metal.

CAUTION: Wait for the blade to reach the maximum
speed and use a slow even feed for proper cutting.

CAUTION: The DWC410 can be used on horizontal
surfaces when the water valve assembly is attached (see
Water Valve Assembly) and used on verticall surfaces
without the water valve assembly attached.

CAUTION: Use clamps or other practical way to secure
and support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and
may lead to loss of control.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Proper Hand Position (Fig. D)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the handle
the other hand on the front of main handle
housing as shown.
Depth of Cut Adjustment (Fig. E)
1. Loosen the depth adjustment knob
14
2. Move the shoe up or down to desired position.
3. Tighten the depth adjustment knob.
Wet Cut Method (Fig. A)

WARNING: Do not use wet cut system unless tool is
protected by the PRCD.

WARNING: To reduce the risk of electric shock, ensure
water will not enter into your tool. Do not touch plug with
wet hands.
1. Follow the instructions described under Mounting the Wet
Cut System.
2. To regulate the water flow, open the water valve by pivoting
15
the lever away from the unit.
3. To close water valve, push the lever toward the unit.
Proceed as described below for straight or angled cuts.
Straight Cuts (Fig. A)
1. Using a marker or grease pencil, mark the area to be cut.
14
2. Place the shoe of the saw on the workpiece ensuring
that the blade does not touch the workpiece.
3. Align the external part of the cutting guide
outline on the workpiece.
4. Turn the tool on and wait for the blade to reach its
maximum velocity.
20
, with
21
or on the motor
13
to release.
16
with the cut