Table of Contents
Advertisement
Available languages
Available languages
EngLIsh
Do not run the power tool while carrying it at your side.
•
Accidental contact with the spinning blade could snag your
clothing, pulling the blade into your body.
Regularly clean the power tool's air vents. The
•
motor's fan will draw the dust inside the housing and
excessive accumulation of powdered metal may cause
electrical hazards.
Don't unplug if plug or receptacle is wet. Disconnect the
•
fuse or circuit breaker that supplies power to the tool. Then
unplug and examine for presence of water in the receptacle.
Wait for the saw to come to a complete stop. An
•
unprotected, coasting blade will cause the saw to walk
backwards, cutting whatever is in its path. Be aware of the
time it takes for the blade to stop after switch is released.
•
Do not use to cut wood or metal.
Never use toothed or segmented diamond blades. This
•
tool is not equipped with a lower guard.
WARNING: Keep hands away from cutting area and
blade. Personal injury may result.
WARNING: To reduce the risk of electrocution, keep all
connections dry and off the ground. Do not touch plug
with wet hands.
WARNING: A Portable Residual Current Device (PRCD) is
provided on the cord set. Receptacles are available having
built in PRCD protection and may be used for an added
measure of safety. When using an extension cord, always
plug into a PRCD protected receptacle or outlet.
WARNING: Always plug extension cord into a PRCD
protected outlet.
WARNING: Test PRCD before each use:
1 . Plug PRCD into power outlet. Indicator should
turn red.
2 . Press test button. Red indicator should disappear.
3 . Press reset button for use. Do not use if above
test fails.
WARNING: Never use saw with salt water or a
conductive fluid.
Additional Safety Rules
Use clamps or another practical way to secure and
•
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and may
lead to loss of control.
Keep your body positioned to either side of the blade,
•
but not in line with the saw blade.
NOTICE: Blades coast after turn off. Serious personal injury
may result.
WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA or less.
Residual Risks
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
•
Impairment of hearing.
22
•
Risk of personal injury due to flying particles.
•
Risk of burns due to accessories becoming hot
during operation.
•
Risk of personal injury due to prolonged use.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the power supply corresponds to the voltage
on the rating plate.
Your D
WALT tool is double insulated in accordance
e
with EN60745; therefore no earth wire is required.
WARNING: 115 V units have to be operated via a fail-safe
isolating transformer with an earth screen between the
primary and secondary winding.
If the supply cord is damaged, it must be replaced by a
specially prepared cord available through the D
service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
•
Safely dispose of the old plug.
•
Connect the brown lead to the live terminal in the plug.
•
Connect the blue lead to the neutral terminal.
WARNING: No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved 3–core
extension cable suitable for the power input of this tool (see
Technical Data).The minimum conductor size is 1.5 mm
maximum length is 30 m.
When using a cable reel, always unwind the cable completely.
Package Contents
The package contains:
1 Water kit
1 Blade spanner
1 Blade wrench
1 Cutting disc
1 Instruction manual
•
Check for damage to the tool, parts or accessories which may
have occurred during transport.
•
Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
WALT
e
; the
2
Advertisement
Table of Contents
