Auto-On/Off Socket Outlet For Power Tools; Autoclean; Antistatic Connection *); Cooling Air Filter - Makita VC4210L Original Operating Instructions

D
Makita VC 4210 L
GB
3.2

Auto-On/Off socket outlet for power tools

F
NL
Appliance socket.
The appliance socket is designed for electrical
I
auxiliary equipment; see technical data for refer-
ence.
N
1. Prior to plugging in an appliance, always switch
off the machine and the appliance that is to be
S
connected.
2. Read the operating instructions to the appliance
DK
to be connected and observe the safety notes
contained in these.
SF
An appliance socket with earthing contact is inte-
E
grated in the machine. An external power tool can
be connected there. The socket features permanent
power on, when the electrical switch is in position
P
, i.e. the machine can be used as an extension
cord.
GR
In position AUTO the machine can be switched on
and off by the power tool connected. Dirt is picked
TR
up from the source of dust immediately. To comply
with regulations, only approved dust producing tools
SLO
should be connected.
The maximum power consumption of the connected
HR
electrical appliance is stated in section "Specifica-
tions".
SK
Before turning the switch to position AUTO ensure
that the tool connected to the appliance socket is
CZ
switched off.
PL
3.3

AutoClean

The machine is equipped with an automatic filter
H
cleaning system, AutoClean. A frequent cleaning cy-
cle will automatically run during operation to ensure
RO
that suction performance is always at its best.
If suction performance decreases or in extensive
BG
dust applications a manually filter cleaning operation
is recommended:
RUS
1. Switch off the machine.
2. Close the nozzles or suction hose opening with
EST the palm of your hand.
3. Turn the switch to position „I" and let the ma-
chine operate at full speed for approx. 10 sec-
LV
onds with the suction hose opening closed.
If suction power is still reduced take out the filter and
LT
clean mechanically or replace filter.
For certain applications, like wet pick up, it is recom-
AL
mended to turn off the automatic filter cleaning sys-
tem. For details see chapter 3.1.
MK
SR
UK
14
CAUTION
3.4 Antistatic connection
CAUTION
The machine is equipped with an antistatic
system to discharge any static electricity that
may develop during dust pick-up.
The antistatic system is placed in front part of the
motor top and creates an earth ground connection to
the inlet fitting of the container.
For proper function the use of an electrical conduc-
tive or antistatic suction hose is recommended.
1. When inserting the optional disposal bag make
sure the antistatic connection is kept.
3.5

Cooling air filter

To protect the electronics and motor, the machine is
equipped with a cooling air diffusor. Clean the cool-
ing air diffusor regularly.
For areas with a high concentration of fine dust in
the surrounding air it is recommended to equip the
machine with an optional cooling air filter cartridge to
prevent dust from settling inside the air channels and
motor. Contact your local sales representative.
CAUTION
If cooling air filter is clogged by dust the over-
load protection switch in the motor can be
activated.
1. In such case switch off the machine, clean cool-
ing air filter and allow machine to cool for ap-
prox. 5 minutes.
3.6

Wet pick-up

CAUTION
The machine is equipped with a water level
limit system which shuts off the machine when
the maximum liquid level is reached.
1. When this occurs, switch off the machine.
2. Disconnect the machine from the socket and
empty the container.
3. Never pick up liquids without the water level limit
system and filter in place.
4. Do not pick up flammable liquids.
5. Before liquids are picked up, always remove the
filter bag/wastebag and check that the water
level limit works properly.
6. If foam appears, stop work immediately and
emty the tank.
7. Clean the water level limiting device regularly
and check for signs of damage.
*) Optional accessories / Option depending on model
*)
Original instruction