Specifications - Makita 9566CVR Instruction Manual

ENGLISH (Original instructions)
1-1. Shaft lock
2-1. Slide switch
3-1. Indication lamp
(speed adjusting dial)
4-1. Indication lamp
5-1. Speed adjusting dial
7-1. Wheel guard
7-2. Bearing box
7-3. Screw
7-4. Lever
8-1. Screw

SPECIFICATIONS

Depressed center wheel diameter
Max. wheel thickness
Rated speed (n) / No load speed (n
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
Noise
The typical A-weighted
according to EN60745:
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
Wear ear protection
Vibration
The vibration total
determined according to EN60745:
Explanation of general view
9-1. Lock nut
9-2. Depressed center grinding wheel
9-3. Inner flange
10-1. Lock nut wrench
10-2. Shaft lock
11-1. Lock nut
11-2. Abrasive disc
11-3. Rubber pad
12-1. Marking A
13-1. Marking B
14-1. Marking C
Model
Spindle thread
)
o
Overall length
Net weight
Safety class
noise level determined
) : 86 dB (A)
pA
) : 97 dB (A)
WA
value (tri-axial vector
9566CR
150 mm
6.4 mm
10,000 min
299 mm
2.4 kg
ENE048-1
Work mode : surface grinding with anti vibration
side grip
Vibration emission (a
ENF002-2
Uncertainty (K) : 1.5 m/s
Work mode : surface grinding with normal side
grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : disc sanding
ENG905-1
Vibration emission (a
Uncertainty (K) : 1.5 m/s
The declared vibration emission value has been
•
measured in accordance with the standard test method
and may be used for comparing one tool with another.
The declared vibration emission value may also be
•
used in a preliminary assessment of exposure.
The declared vibration emission value is used for
•
main applications of the power tool. However if the
ENG900-1
power tool is used for other applications, the
vibration emission value may be different.
sum)
WARNING:
The vibration emission during actual use of the power
•
tool can differ from the declared emission value
depending on the ways in which the tool is used.
4
15-1. Pin
15-2. Vent
17-1. Wire cup brush/Wire bevel brush
18-1. Lock nut
18-2. Abrasive cut-off wheel/
diamond wheel
18-3. Inner flange
18-4. Wheel guard for abrasive cut-off
wheel/diamond wheel
19-1. Exhaust vent
19-2. Inhalation vent
M14
-1
/II
) : 6.5 m/s
h,AG
2
) : 7.0 m/s
h,AG
2
) : 2.5 m/s
h,DS
2
9566CVR
150 mm
6.4 mm
M14
-1
10,000 min
299 mm
2.4 kg
2
2
2
ENG902-1