Hikvision DS-PK-LRT(433MHz) - Wired Keypad Manual

Table of Contents

Contents

1 Components and Beeps
2 Address Settings
3 Wiring and Installation
4 Operation Commands
5 Specification
6 Legal and Regulatory Information
- 6.1 Trademarks
7 Documents / Resources
- 7.1 References
- 7.2 Download manual

Components and Beeps

Indicator

Set	Solid Green: No Configuration Flashing Green: In the Configuration Status
Fault	Solid Orange: System Fault Off: No Fault
Network	Solid Green: All Enabled Channels Connected Normally Off: Part of or All Enabled Channels Connected Abnormally
Armed/Disarmed	Solid Blue: Armed Off: Disarmed
Alarm	Flashing Red: Alarm Occurred/Tamper Alarm Off: No Alarm

Key

	Query		Project		Bypass		Medicine		Scoll Up
	Fire		Panic		One-Push to Arm				Scoll Down

Beeps

One Beep Pressing keys/command timed out or too long.
Two Beeps: Valid command/Report uploaded.
Five Beeps: Invalid command/Failed to upload the report in 60s.
Continuous Beeping For Two Seconds: Fault prompt (Only for the Network Control Panel)
Slowly Continuous Beeps: In the Entry/Exit delay status.
Rapidly Continuous Beeps: In the Entry/Exit delay status, 10 seconds countdown.
Rapid Beeps: Zone alarm/keypad not enrolled.
Three Long Beeps and Two Short Beeps: Keypad tampered.
Three Beeps: Keypad enrolled.

Address Settings

Configure the address via DIP switch of the keypad before powering on the system. The address should be in the range (for Network Control Panel, 0 to 31; for Hybrid Control Panel, 0 to 23). The address of each keypad should be unique. The binary value shown in the diagram is 00010, which means the decimal value is 2. So the address of the keypad is 2.

Wiring and Installation

Dimension

Device Dimensions

Wiring

Note: Hybrid control panel does not support Z1, GND, NO/NC, COM.

Install Keypad

Gangbox Mounting
Wall Mounting

It is required to insert the screw for tamper alarm.

Operation Commands

Scan the QR code a to get operation commands of Hybrid control panel.

Specification

Model	DS-PK-L	DS-PK-LR	DS-PK-LRT	DS-PK-LRTE
Numeric key	12 keys: 0 to 9, *, #
Function key	8 keys: Project/Query/Bypass/One-push to arm/Fire/Panic/Scroll up/Scroll down
Display	LCD screen
Keyfob	N/A	N/A	Two-way keyfob	Two-way keyfob
Tamper switch	1
RS-485 interface	1
Sound	buzzer
Tag/Card reading	N/A	N/A	Support	Support
Power supply	12 V, 0.15 A
Power consumption	1.8 W
Temperature	-10°C to 55°C
Humidity	10% to 90%
Dimension (L × W × H)	164 mm × 124 mm × 31 mm
Weight	272 g

Legal and Regulatory Information

Trademarks

and other Hikvision's trademarks and logos are the properties of Hikvision in various jurisdictions. Other trademarks and logos mentioned are the properties of their respective owners.

This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the RE Directive 2014/53/EU, the EMC Directive 2014/30/EU, the LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU.

warning The Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source according to the IEC60950-1 standard. Please refer to technical specifications for detailed information.

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info