Canon DP-V2730 Operation Manual
  1. Manuals
  2. Brands
  3. Canon Manuals
  4. Monitor
  5. DP-V2730
  6. Operation manual

Canon DP-V2730 Operation Manual

Video display
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Video Display
Firmware ver. 1.1
Firmware ver. 1.0
• Before use, be sure to read this guide, including the safety and handling precautions.
• Reading this guide will help you learn to use the video display properly.
• Store this guide safely so that you can use it in the future.
Operation Guide
Instruction Manual
English

Advertisement

Table of Contents
loading

Related Manuals for Canon DP-V2730

Summary of Contents for Canon DP-V2730

  • Page 1 Video Display Operation Guide Firmware ver. 1.1 Firmware ver. 1.0 • Before use, be sure to read this guide, including the safety and handling precautions. Instruction Manual • Reading this guide will help you learn to use the video display properly. English • Store this guide safely so that you can use it in the future.

  • Page 2: Table Of Contents

    About the User Manual for the Display • The product includes an Instruction Manual or Setup Guide. Before using the product, be sure to read “Important Usage Instructions” and “Safety Instructions and Handling Precautions”. • The Operation Guide (this document) explains the functions available on the version of the firmware shown on the cover page as well as setup procedures. Table of Content OSD Menu Introduction Adjustment 21 About this manual 3 Channel Settings 36 Trademarks 3 Display Settings 41 Operating the Video Display Audio Settings 44 Basic operations to use the OSD menu 4 Marker Settings 45 Adjusting Image Quality While Viewing the...

  • Page 3: Introduction

    Introduction The On Screen Display (thereafter referred to OSD) default language setting is English. To change the OSD menu language setting, please refer to p.70. About this manual The screen of the DP-V1830 is used as an example in this Guide. Some of the illustration used in the Guide have been simplified for clarity. Conventions used in this manual : Indicates a reference page. Reference: Indicates reference information. CAUTION: Indicates an item you must observe. Note: Indicates a note. [Adjustment] [Picture Mode]: P ressing the MENU button shows the OSD Menu levels. You can move between the items and select from them. • The following symbols show differences in functions and settings depending on the product. : Explanations are applicable to the indicated products. Trademarks • HDMI, HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the U.S. and other countries. • VESA is a registered trademark or trademark of Video Electronics Standards Association in the U.S. and other countries. • Apple and Safari are trademarks of Apple Inc. registered in the United States and other countries. • Google and Google Chrome are trademarks or registered trademarks of Google LLC. • Other product and company names herein are trademarks or registered trademarks of their respective owners.

  • Page 4: Operating The Video Display

    Operating the Video Display Using buttons and jog dial on the video display, you can adjust image quality and configure settings for input signals. In addition, you can assign frequently used functions to the CH (Channel) and F (Function) buttons. Items that cannot be set due to other function settings are hidden or grayed out. Basic operations to use the OSD menu The video display settings are changed from the OSD menu. MENU button RESET button Opens/closes the OSD Resets the items to be adjusted using the slider and menu, or moves up one entered characters. level in a menu. Jog dial or rotation: U sed to move to a different item and change settings. Press: Confirms settings or moves the selection frame up/down 1 level. 1 Open the OSD menu. Main Menu Sub Menu Setting Options • Press the MENU button. 2 Select the Main Menu.

  • Page 5: Adjusting Image Quality While Viewing The Entire Image

    Operating the Video Display 4 Select the setting to change. • Select the setting to change using the jog dial and press it to determine the selection. You will be returned to the Sub Menu item selection screen. 5 Exit menu. • Pressing the MENU button will return you to the Main Menu item selection screen. Pressing the MENU button again will close the menu screen. Note • To adjust image quality, warming-up is necessary to stabilize the brightness of the video display. Wait at least 10 minutes after turning on the power before use. • The OSD menu and slider will disappear automatically if no operation is performed for approximately 1 minute. The function button guige will disappear automatically if no operation is performed for approximately 10 seconds. • The settings that cannot be set, are grayed out. • The following functions can be returned to their factory default settings or their anchor point ( 7) by pressing the RESET button, after adjusting the image quality. - [Luminance], [Brightness], [Chroma], [HDR Range], [Power], [Saturation], [Offset], [Slope] When [Picture Mode] [User 1–9]: When executing calibration, pressing the RESET button while adjusting the image quality will return you to the settings after calibration. Adjusting Image Quality While Viewing the Entire Image You can adjust the OSD menu to display as a slider at the bottom of the screen. This allows for the image quality to be adjusted whilst it is displayed on the screen.
  • Page 6 Operating the Video Display Color temperature detailed settings (gain, bias) You can adjust RGB all at once or individually when the screens for adjusting [Gain] or [Bias] are displayed. 1 Select [Adjustment] [Color Temperature]. • [Gain R], [Gain G], [Gain B], [Bias R], [Bias G], and [Bias B] can be set individually using the jog dial ( ). 2 Select one. • The setting screen for [Gain] or [Bias] will be displayed. 3 Switch the guide in the upper right area of the slider screen using the jog dial ( • The indication changes to [RGB], [R], [G], and [B]. Selecting [RGB] will allow you to adjust RGB as a whole.

  • Page 7: Temporarily Saving Parameters (Anchor Point Setting)

    Operating the Video Display Temporarily Saving Parameters (Anchor Point Setting) You can temporarily save parameters for [Luminance], [Brightness], [Chroma], and [HDR Range]. See 27 for setting anchor points during CDL adjustment. 1 Select [Adjustment] [Anchor Adjustment]. 2 Press the jog dial, and when the confirmation screen appears, select [OK]. • The parameter is saved and the anchor point is set. 3 Adjust the image quality again and press the RESET button on the video display. • Returns you to the anchor point for each function.

  • Page 8: Changing Image Quality Automatically According To Input Signal

    Operating the Video Display Changing Image Quality Automatically According to Input Signal On this video display, you can automatically change the image quality according to video resolution or metadata. Changing [Picture Mode] automatically ( 1 Select [Channel Settings] [Select Channel]. • Select the channel. 2 Select [Channel Settings] [Picture Mode] [Type]. 3 Select the Type using the jog dial. Changing by individual video resolution (4K/2K) Select [4K/2K].

  • Page 9: Export/Import

    [LUT Import]. 3 Select the LUT file to import. • In the [Filename] field, search and display a file with extension ".clut" and ".cube" in the root folder. 4 Select the LUT No. to save the LUT. 5 Select [Execute]. • When the confirmation screen appears, select [OK]. Import starts. Note • Import of [LUT] can also be set from [Adjustment] [CDL/User LUT] [LUT Import]. • The LUT file (.clut format) is proprietary to Canon Video Display. Refer to the Canon website for the file format and how to create the LUT file. • Up to 1000 LUT import files are recognized. • You can delete the imported LUT, as well as rename the LUT ( 28). The configuration of LUT files (cube format) is shown below. „ LUT filename...
  • Page 10 Operating the Video Display „ Concept Drawing of Display Image Processing and LUT LUT Preset Color Gamut/Gamma/ Range Range 3D-LUT HDR Range, etc. conversion conversion Import Export/Import OSD Menu Settings ( 1 Select [System Settings] [Export/Import]. 2 Select [Export] or [Import]. Exporting 1Select [Target] from [USB], [User 1] to [User 3] or [LAN].

  • Page 11: Set Date/Time

    Operating the Video Display Exporting/Importing CDL Parameters ( 1 Select [Adjustment] [CDL/User LUT]. 2 Select [CDL 1-8]. 3 Select [Detail Settings] [CDL Export] or [CDL Import]. Exporting 1Select [CDL Preset]. 2Select a file format ".ccc" or ".cdl". Importing 1Select [Filename]. 2Select [CDL Preset]. 4 Select [Execute]. • When the confirmation screen appears, select [OK]. Export/Import starts. Note • The exported file is automatically saved under the name "YYYYMMDDhhmmss_Preset name.ccc (cdl)". • Up to 1000 CDL import files are recognized. Set Date/Time ( This section describes how to set the video display Date/Time. The video display Date/Time will be reset if the power cord is not connected for approximately 20 days.

  • Page 12: Inputting Characters

    Operating the Video Display Inputting Characters This section describes how to input the characters. 1 When the character input screen is displayed, use the jog dial ( ) to select the area you wish to input. 2 Select characters using the jog dial ( or rotation). • The following characters can be selected: Press buttons to display them one by one.

  • Page 13: Using The Function (F) Buttons

    Operating the Video Display Using the Function (F) Buttons You can assign functions to the F buttons on the video display to execute them instantly. You can assign different functions on F buttons in the normal and ALT modes respectively. 1 Select [System Settings] [Function/Channel Button] [Function Button] or [Function Button (ALT)]. • The button selection screen will be displayed. 2 Select the button name and press the jog dial. 3 Select the function to assign. • Refer to the "Function to allow registration for the display F buttons ( 74)" for the available functions.

  • Page 14: Using The Channel (Ch) Button

    Operating the Video Display Using the Channel (CH) Button You can assign channels (various settings related to input signal) to the CH buttons on the video display and switch channels instantly. 1 Select [System Settings] [Function/Channel Button] [Channel Button]. • The button selection screen will be displayed. 2 Select the button name and press the jog dial. 3 Select the channel to assign. • See [Channel Settings] ( 36) for the configurable settings. 4 Press the jog dial. • The setting is confirmed.
  • Page 15 Operating the Video Display The following content is assigned to channel buttons on the video display and to each channel by factory default. Default Values by Channel Item Input Configuration 12-3G/ HDMI 12-3G/ 12-3G/ Multi View Not set HD-SDI HD-SDI HD-SDI Select Input Signal Automatic — Automatic Image Division Automatic Multi View Automatic (Quad) Screen A ~ D — SDI Input — A ~ D Link Order Automatic Format Automatic Audio Input Automatic SDI Input A Automatic Switch Out...

  • Page 16: Checking Signal Information And Status Of The Main Unit

    Operating the Video Display Checking Signal Information and Status of the Main Unit The video display is equipped with a banner display function. 1 Press the jog dial when the OSD menu is closed. • The channel name, signal information, and status of the main unit will be displayed in the banner. It will automatically disappear after 6 seconds. Note • You can select how the banner is displayed ([Banner] 71). • You can monitor the input signal status. ([Signal Monitoring] • For more detailed signal information, please refer to the section on [Signal Information] ( 76). • The [Detecting sync.] banner will continue to appear until the input signal is synchronized. Operating the video display using an external device [GPI terminal] You can operate the video display using an external device connected to the GPI terminal and execute the functions registered in each pin. Remote operation is possible only when the video display is turned on.

  • Page 17: Operating The Video Display Using An External Device [Lan Terminal]

    Operating the Video Display Operating the video display using an external device [LAN terminal] The video display supports Television Systems Ltd.’s “TSL UMD Protocol Ver. 5.0”. You can operate the video display using an external device connected to the LAN terminal and display characters and tally lights on the screen. There are two tally lights, on the left and right. Up to 16 characters can be displayed. Tally display (left) Character display Tally display (right) 1 Connect an external control device to the LAN terminal. 2 Set [SCREEN] and [INDEX] to [0x0000] in the TSL Protocol settings. 3 Select [Network/IMD Settings] [In Monitor Display].

  • Page 18: Use A Web Browser To Remotely Operate The Video Display

    Operating the Video Display Use a web browser to remotely operate the video display Operate the video display remotely using a web browser on a computer terminal or other device connected to the LAN terminal. From the device connected to the network, you can change image quality settings or switch channels. This function checks operation using the following web browsers. • Safari (Apple) • Google Chrome (Google) * Correct operation cannot be guaranteed on all supported OS or web browser editions. CAUTION • Remember to change the default settings for ID and Password when using this function. Note • Access is only possible from a single terminal. • Opening multiple pages in multiple tabs on the web browser can cause it to not function properly. • Operating the video display itself while it is being accessed from a web browser can cause the network connection to be lost. • A delay may occur in video display or in the various settings depending on the network environment and communication conditions. • The IP address can be checked in the [System Information] screen. • The operation screen only displays English. 1 Connect external control devices via the network. 2 Select [Network/IMD Settings] [Web].
  • Page 19 Operating the Video Display „ Operation screen [Control] screen Allows the Picture Mode, Channel, and various marker displays to be set. [Value / Name]* Enter characters or numbers. [Get]: Acquires input data. [Set]: Applies the data to the input screen. [Zoom / Pixel Value] Sets the display position for [Zoom] or the pixel position for [Pixel Value Check]. Click [Position / Function] to display the screen where you can select the F buttons. * [Value] • [ Value] does not show decimal points. • D epending on the setting item, the value may be different from the value displayed on the menu. [Setting] screen You can import LUT, export the error log of [Signal Monitoring], and import or export the settings of the video display. [LUT Import (3D-LUT)] Imports a LUT. [Signal Monitoring Log Export] Exports the error log of [Signal Monitoring].
  • Page 20 Operating the Video Display [lnformation] screen Displays the settings for [Adjustment] and [Channel Settings], and information for [Signal Information] and [System Information]. [Link] screen You can display a list of the display connected via LAN to this video display, set [Display Setting Link], and change the display names.

  • Page 21: Osd Menu

    Adobe RGB [ITU-R BT.709], [ITU-R BT.2020], [Adobe RGB], [DCI-P3]: Mode set to the brightness, color temperature, gamma/EOTF, and color gamut of the DCI-P3 User 1 (2020 PQ) three primary colors chromaticity points of each standard. User 2 (2020 HLG) [User 1–9] (User 1 (2020 PQ), User 2 (2020 HLG), User 3 (DCI PQ), User 3 (DCI PQ) User 4 (DCI PQ D65), User 5 ~ User 9): This mode allows you to set each User 4 (DCI PQ D65) item in [Adjustment] individually. You can change the mode name User 5 ~ User 9 within 24 one-byte characters including alphabetical characters, CINEMA EOS SYSTEM numbers, and symbols ( 30). ACESproxy (ver. 1.0.1) [CINEMA EOS SYSTEM]: Canon Log is the ideal mode for displaying images captured with Cinema EOS cameras. Using Camera Link, you can have the image quality setting change automatically ([Automatic Adjustment (CINEMA EOS)] 60). [ACESproxy (ver. 1.0.1)]: A mode to display ACESproxy videos in optimum gamma/EOTF and color gamut. • [Aces proxy (ver. 1.0.1)] cannot be set when [Channel Settings] [Picture Mode] [Type] is set to an option other than [Normal]. Luminance 0 to 1000.0 Adjusts the peak brightness (Increments of 0.1). • The luminance values are just a guide and not guaranteed absolute values. Brightness -500 to 500 (0) Adjusts the black level of the image. (Increments of 1) Chroma 0 to 2000 (1000) Adjusts the color saturation of the image (color depth). (Increments of 1) • [Chroma] is not settable in the following cases:...
  • Page 22 OSD Menu Sub Menu Setting Options (Bold: factory default) Backlight Control Local Dimming Switches the backlight control method. Automatic / High / Low, Local dimming technology controls the amount of light emitted by the backlight for each display area. The backlight of bright area is increased and the dark area is decreased according to the displayed content. • [Automatic]: This mode is suitable for checking HDR images. [High]: This mode is suitable for checking images with a lot of bright areas. [Low]: This mode is suitable for checking SDR images. • When [Channel Settings] [Picture Mode] [Type] [Quad] or [Dual] is selected, the setting is fixed to the setting of screen A. Color Temperature D93, D65, D65 Custom, Sets the color temperature. ( D61, D60, D56, D50, DCI-P3 [D93], [D65], [D61], [D60], [D56], [D50], [DCI-P3]: Select from preset color Custom (xy), Off temperatures. [D65 Custom]: This preset is for adjusting the color of the video display • When a preset is and displays having different display characteristics. The gain and selected bias are adjusted based on D65. Gain/Bias Setting Target: [Gain/Bias Setting Target]: The gain/bias parameter is reflected in all Common, Each...
  • Page 23 [Cinema Gamut to DCI]: Modes where the color gamut is converted to S-Gamut3 to 709 monitor Cinema Gamut video recorded by the Cinema EOS cameras. S-Gamut3 to 2020 [S-Gamut3 to 709], [S-Gamut3 to 2020], [S-Gamut3 to DCI], S-Gamut3 to DCI [S-Gamut3.Cine to 709], [S-Gamut3.Cine to 2020], S-Gamut3.Cine to 709 [S-Gamut3.Cine to DCI]: Preset modes where the color gamut is S-Gamut3.Cine to 2020 converted. S-Gamut3.Cine to DCI • [Color Gamut] cannot be set in the following cases. - When [CDL/User LUT] [ARRI (Rec2100-PQ-1K-100)], [ARRI (Rec2100- HLG-1K-200)], [VARICAM (V-Log to V-709)], [RED (Log3G10 to 709/1886)], [RED (Log3G10 to 2020/PQ)], [2020 PQ to 2020 SDR], [2020 PQ to 709 SDR], [2020 HLG to 709 HLG] or [2020 HLG to 709 SDR] is selected. • For checking the video captured with Cinema EOS cameras, please refer to the "Parameter of Cinema EOS cameras and Canon displays ( 62)". Gamma/EOTF 1.0, 2.2, 2.35, 2.4, 2.6, Sets the Gamma/EOTF. ITU-R BT.1886 SMPTE ST 2084 (PQ) [1.0], [2.2], [2.35], [2.4], [2.6], [ITU-R BT.1886], [Canon Log], [Canon Log 2], Hybrid Log-Gamma [Canon Log 3]: Select the preset gamma. Canon Log [SMPTE ST 2084 (PQ)], [Hybrid Log-Gamma], [Canon Log (HDR)], Canon Log (HDR) [Canon Log 2 (HDR)], [Canon Log 3 (HDR)], [S-Log2 (HDR)], [S-Log3 (HDR)]: Select the gamma/EOTF for HDR display. Canon Log 2 Canon Log 2 (HDR) Canon Log 3  About [Hybrid Log-Gamma]...
  • Page 24 OSD Menu Sub Menu Setting Options (Bold: factory default) HDR Range Sets the display method when Gamma/EOTF for HDR display is selected. SMPTE ST 2084 (PQ) 100 to 10000 (1000) Sets the [SMPTE ST 2084 (PQ)] dynamic range to be displayed, from 0.005 to 10,000 cd/m (nits). (100 to 4000: 100 increments. 4000 to 10000: 1000 increments) Hybrid Log-Gamma 100 to 1000 Sets how far to display the [Hybrid Log-Gamma] dynamic range. (in increments of 100) The upper limit value will change to match the settings of [HLG System Gamma]. ( Canon Log (HDR) 100 to 800 Sets the [Canon Log] dynamic range to be displayed, from 0 to 800%. (in 100 increments) Canon Log 2 (HDR) 100 to 1600 Sets the [Canon Log 2] dynamic range to be displayed, from 0 to 1600%. (in 100 increments) Canon Log 3 (HDR) 100 to 1600 Sets the [Canon Log 3] dynamic range to be displayed, from 0 to 1600%. (in 100 increments) S-Log2 (HDR) 100 to 1400 (1000) Sets how far to display the [S-Log] dynamic range. (in 100 increments) S-Log3 (HDR) 100 to 3900 (1000) Setting procedures The explanation uses [SMPTE ST 2084 (PQ)] as an example.
  • Page 25 OSD Menu Sub Menu Setting Options (Bold: factory default) Color Range Automatic Sets the quantization range. Full SDI Full (4-1019) [Automatic]: Sets the range based on signal information automatically. Limited • Setting is disabled when [ACESproxy (ver. 1.0.1)] is selected for [Picture Mode]. • Operations when [Automatic] is selected are described below. - It is set in accordance with the settings if Color Range settings are included in the camera metadata. When there is [Full Range] metadata in Payload when SDI is selected, it will be set to [SDI Full]. - When HDMI is selected, [Full] or [Limited] is set automatically depending on HDMI signal information. - When SDI is selected, the setting is configured according to the settings for [Picture Mode], [Color Gamut], and [Gamma/EOTF] ( 32). When [Channel Settings] [Input Configuration] [Multi View] is selected, none of camera metadata, SDI Payload, and HDMI signal information are linked. • Operations when [Format] is set to [ICtCp] are described below. - When [Color Range] is set to an option other than [Full], [Wave Form Monitor] will display only a signal set with [Color Range].
  • Page 26 • When [ARRI (Rec2100-PQ-1K-100)] or [RED (Log3G10 to 2020/PQ)] is selected, LUT 8 [HDR Range] [SMPTE ST 2084 (PQ)] setting is less than 1000, the setting becomes [1000]. • When [ARRI (Rec2100-HLG-1K-200)] is selected, [HDR Range] [Hybrid Log- Only when [Picture Gamma] settings become [1000]. Mode] is [User 1-9] • [Color Gamut] and [Gamma/EOTF] are set in accordance with the [User LUT] ARRI (Rec2100-PQ- settings ( 32). 1K-100) • Not settable in the following cases: ARRI (Rec2100-HLG- When [Color Gamut] is set to [Cinema Gamut to XXX] or [S-GamutXXX] 1K-200) When [Gamma/EOTF] is set to [Canon Log], [Canon Log 2] or [Canon Log 3] VARICAM (V-Log to When [2020 Constant Luminance] is set to [Constant] When the [Format] signal method is set to ICtCp or XYZ V-709) RED (Log3G10 to 709/1886) RED (Log3G10 to 2020/PQ) 2020 PQ to 2020 SDR 2020 PQ to 709 SDR 2020 HLG to 709 HLG 2020 HLG to 709 SDR l When [CDL 1-8] is selected Power 0.50 to 4.00 (1.00) Adjusts the Gamma of the image. (0.01 increments) Saturation 0.000 to 2.000 (1.000)
  • Page 27 OSD Menu Sub Menu Setting Options (Bold: factory default) Detail Settings CDL Export Exports CDL parameters. CDL Preset CDL 1 to CDL 8 File Type CCC, CDL Execute CDL Import Imports CDL parameters. Filename CDL Preset CDL 1 to CDL 8 Execute CDL Preset Name You can change the name of [CDL 1-8] within 16 characters including alphabetical characters, numbers, and symbols. Anchor CDL You can temporarily save parameters for [Power], [Saturation], [Offset], and [Slope] and recover the values. (anchor point setting) Reset CDL Resets CDL parameters. l When [User LUT 1-8] is selected Select a preset of the LUT. LUT Import Same as [Detail Settings] [LUT Import], [LUT Name], [LUT Delete] LUT Name LUT Delete Color Range Automatic, Manual Sets the method of color range conversion performed before and after User LUT processing (input/output).
  • Page 28 OSD Menu Sub Menu Setting Options (Bold: factory default) Video Signal Apply, No Apply Select whether or not to apply the LUT when the wave form monitor, Information vector scope or other image signal information is displayed. Bypass On, Off When set to [On], you can return to the image quality before User LUT was applied. • When [Picture Function Settings] [Compare View] [Enable] [On], this item is fixed to [Off]. • Parameters are stored until the video display is turned off. • Bypass is set to [Off] in the following cases: - [Picture Mode] has been changed - When the [CDL/User LUT] setting has been changed - [Picture Function Settings] [Compare View] [Enable] settings have been changed • When [Channel Settings] [Picture Mode] [Type] [Quad] or [Dual] is selected, the [Bypass] setting is reflected in [Picture Mode] of each of screens A to D.
  • Page 29 Setting Options (Bold: factory default) 2 020 Constant Constant Luminance When [Picture Mode] or [Color Gamut] [ITU-R BT.2020] Luminance Non-constant Sets the color matrix conversion method. Luminance [Constant Luminance]: YUV signals are linearly converted and then converted into RGB signals. [Non-constant Luminance]: YUV signals are converted into RGB signals without changing gamma 0.45. • Not settable in the following cases: When [Gamma/EOTF] is set to [Canon Log], [Canon Log 2] or [Canon Log 3] When the [Format] signal method is set to ICtCp or XYZ [Channel Settings] [Picture Mode] [Type] [Quad] or [Dual] When [Channel Settings] [Input Configuration] is set to [HD/SD-SDI], this item is fixed to [Non-constant Luminance]. 2020 Gamut Mapping Gamut Mapping When [Picture Mode] or [Color Gamut] [ITU-R BT.2020] Clipping [Gamut Mapping]: Mapping is performed on colors outside the native color gamut by Canon's unique method. [Clipping]: Colors outside the native color gamut are clipped by a general method. • This cannot be set when [Channel Settings] [Picture Mode] [Type] [Quad] or [Dual] is selected.
  • Page 30 OSD Menu Sub Menu Setting Options (Bold: factory default) HDMI Link When [Picture Mode] [User 1–9] Video is displayed at the image quality linked to the video image quality setting using the HDMI metadata. • This cannot be set when [Channel Settings] [Input Configuration] [Multi View] is selected. • Parameter of HDMI metadata and Video Display ( Automatic Adjustment On, Off Turns the HDMI link on/off. Color Gamut/Gamma/ On, Off Matches the [Color Gamut] and [Gamma/EOTF] settings of the video EOTF...
  • Page 31 ■ Relationship between [Color Gamut] and [Gamma/EOTF] that can be selected When [Color Gamut] is changed, [Gamma/EOTF] is changed to the underlined value (default value) when the current [Gamma/EOTF] settings are not selectable. Picture Mode Color Gamut Selectable Gamma/EOTF ITU-R BT.709, Cannot be selected 1.0, 2.2, 2.35, 2.4, 2.6, ITU-R BT.1886, SMPTE ST 2084 (PQ), Hybrid Log-Gamma, ITU-R BT.2020 Canon Log, Canon Log (HDR), Canon Log 2, Canon Log 2 (HDR), Canon Log 3, Canon Log 3 (HDR), S-Log2 (HDR), S-Log3 (HDR) Adobe RGB 1.0, 2.2, 2.35, 2.4, 2.6, ITU-R BT.1886 DCI-P3 1.0, 2.2, 2.35, 2.4, 2.6, ITU-R BT.1886, SMPTE ST 2084 (PQ), Canon Log, Canon Log (HDR), Canon Log 2, Canon Log 2 (HDR), Canon Log 3, Canon Log 3 (HDR), S-Log2 (HDR), S-Log3 (HDR) CINEMA EOS ITU-R BT.709, 1.0, 2.2, 2.35, 2.4, 2.6, ITU-R BT.1886, SMPTE ST 2084 (PQ), Hybrid Log-Gamma, SYSTEM, ITU-R BT.2020 Canon Log, Canon Log (HDR), Canon Log 2, Canon Log 2 (HDR), Canon Log 3, User 1-9 Canon Log 3 (HDR), S-Log2 (HDR), S-Log3 (HDR) Adobe RGB 1.0, 2.2, 2.35, 2.4, 2.6, ITU-R BT.1886 DCI-P3 1.0, 2.2, 2.35, 2.4, 2.6, ITU-R BT.1886, SMPTE ST 2084 (PQ), Canon Log, Canon Log (HDR), Canon Log 2, Canon Log 2 (HDR), Canon Log 3, Canon Log 3 (HDR), S-Log2 (HDR), S-Log3 (HDR) Native 1.0, 2.2, 2.35, 2.4, 2.6, ITU-R BT.1886, SMPTE ST 2084 (PQ)
  • Page 32 OSD Menu ■ Operations when [Color Range] [Automatic] (when SDI is selected) Setting Options Color Range to be Set Picture Mode DCI-P3 DCI-P3 Color Gamut Cinema Gamut to DCI Canon Log (HDR) Full Canon Log 2 (HDR) Gamma/EOTF Canon Log 3 (HDR) S-Log2 (HDR) S-Log3 (HDR) Other than the above Limited ■ Parameter of [User LUT] and [Color Gamut] / [Gamma/EOTF] User LUT Color Gamut...
  • Page 33 OSD Menu ■ Details of the factory default settings for each [Picture Mode] Item ITU-R BT.709 ITU-R BT.2020 Adobe RGB DCI-P3 Luminance 100.0 100.0 100.0 48.0 Brightness Chroma 1000 1000 1000 1000 Backlight Control Local Dimming Low Local Dimming Low Local Dimming Low Local Dimming Low Color Preset DCI-P3 Temperature 0.313 0.313...
  • Page 34 OSD Menu User 5 to Item User 1 User 2 User 3 User 4 User 9 Luminance 1000.0 1000.0 1000.0 1000.0 100.0 Brightness Chroma 1000 1000 1000 1000 1000 Backlight Control Local Dimming Local Dimming Local Dimming Local Dimming Local Dimming Automatic Automatic Automatic Automatic Color Preset DCI-P3 Temperature...
  • Page 35 Local Dimming Low Color Preset Temperature 0.313 0.322 0.329 0.338 Gain/Bias Common Common Setting Target Gain R/G/B 1023/1023/1023 (When [D65 Custom]: 1000/1023/1023) Bias R/G/B Color Gamut ITU-R BT.2020 – Gamma/EOTF Canon Log 2 (HDR) – Color Range Automatic – Output Transform – DCI-P3 Output Transform – Dark Surround Surround CDL/User LUT Off Off YCbCr Color Matrix Automatic Automatic 2020 Constant Luminance Non-constant Luminance...

  • Page 36: Channel Settings

    OSD Menu Channel Settings This menu is used for input related settings. Select the [Select Channel] and choose a channel number from CH1 to CH20. Finally define the parameter of each of the [Channel Settings].  "Supported Signal Format" ( Sub Menu Setting Options Select Channel CH1 to CH20 Display the channel number. In addition, you can assign each content of [Channel Settings] to each channel ( 14). • It may take 3 seconds when switching channels. Input Configuration 12-3G/HD-SDI Select the input. Factory default depend on the channel ( 15). HD/SD-SDI When [Multi View] is selected, the signal to be input to each of the screens HDMI can be selected from an SDI signal or an HDMI signal. SD-SDI signals Multi View cannot be displayed. — (Not set) Select Input Signal Automatic Sets the signal display method. Quad Input Dual Input A,B [Automatic]: The display method is automatically determined to match the Dual Input C,D input signal. Single Input A [Quad Input]: Four input signals (Input A to Input D terminals) are Single Input B displayed.
  • Page 37 OSD Menu Sub Menu Setting Options Image Division When [Input Configuration] [12-3G/HD-SDI] Sets the display method when using either [Quad Input] or [Dual Input]. Two division methods "Square Division" and "2 Sample Interleave" are supported for 4K video signals. When [Input Configuration] [Multi View] The multi-screen display method can be selected from [Multi View (Quad)] or [Multi View (Dual)]. Automatic [Automatic]: Automatically determined based on payload and displayed. [Square Division]: Displays a signal transmitted over four inputs as a single [Select Input Signal] image. When [Quad Input] [2 Sample Interleave]: Displays a signal transmitted divided into a 2K/HD Square Division signal as a single image. 2 Sample Interleave [Multi View (Quad)]: Each of the images from the four inputs are shown in Multi View (Quad) four screens. [Multi View (Dual)]: Each of the images (Inputs A/B or Inputs C/D) from the [Select Input Signal] two inputs are shown in two screens. When [Dual Input] 2 Sample Interleave Multi View (Dual) Select Input Signal: Q uad Input, Image Division: Square Division • The combinations of video signal formats that can be displayed when using two screens or four screens in [Multi View (Quad)] or [Multi View (Dual)] are as follows: - Resolution combinations: Same, or “4096x2160, 2048x1080”, “3840x2160, 1920x1080”...
  • Page 38 - [Color Gamut]: [ITU-R BT.709] or [ITU-R BT.2020] 4:4:4 RGB 12-bit - [Gamma/EOTF]: [SMPTE ST 2084 (PQ)] or [Hybrid Log-Gamma] 4:4:4 XYZ 10-bit • If you need to use the ICtCp format for SDI signals, select any of the following to match the signal: [4:2:2 ICtCp 10-bit], [4:2:2 ICtCp 12-bit], [4:4:4 ICtCp 10-bit], 4:4:4 XYZ 12-bit [4:4:4 ICtCp 12-bit] HDMI Signal / Multi • To use 4:4:4 XYZ 10-bit for SDI signals, select [4:4:4 XYZ 10-bit]. Then, signals View will be processed as signals where XYZ data is included in RGB data output in Automatic 4:4:4 RGB 10-bit format. • With SDI signals, when [Color Gamut] is set to [Cinema Gamut to XXX] or [S-GamutXXX], or when [Gamma/EOTF] is set to [Canon Log], [Canon Log 2] or [Canon Log 3], operation changes as follows according to the color format. ICtCp/RGB: Operates as YCbCr XYZ: Operates as RGB Audio Input [Select Input Signal] Sets the audio terminal. When [Quad Input] Automatic, Input A, [Automatic]: Sets automatically to match the input signal. Input B, Input C, Input D • For [Select Input Signal] [Automatic] or [Single Input], it is fixed at [Automatic]. When [Dual Input A,B] • When [Input Configuration] [Multi View] is selected, the list of terminals set in Automatic, Input A, [Screen A to D] is displayed and can be set.
  • Page 39 OSD Menu Sub Menu Setting Options Channel Name Sets the name of the selected channel. You can input up to 16 alphanumeric characters. Picture Mode Set [Picture Mode] by individual channel. Type Normal [Normal]: Sets one [Picture Mode]. 4K/2K [4K/2K]: Sets [Picture Mode] by individual 4K or 2K signal screen. Automatic [Automatic]: [Picture Mode] is set according to the SDI signal. The set Quad [Picture Mode] is changed to in the order camera metadata → Dual Payload → resolution (4K/2K). [Quad]: Sets a picture mode for each of screens A to D when [Image Division] is set to [Multi View (Quad)]. [Dual]: Sets a picture mode for each of screens A and B when [Image Division] is set to [Multi View (Dual)]. [Type] ITU-R BT.709 Set the [Picture Mode] for each screen. When [Normal] ITU-R BT.2020 Picture Mode Adobe RGB [ACESproxy (ver. 1.0.1)]: Can be set when [Type] is [Normal]. DCI-P3 [—] (Not set): Cannot automatically change image quality to suit input When [4K/2K] User 1 (2020 PQ) signal. Can be set when other than [Resolution 4K] and [Resolution Resolution 4K, 2K User 2 (2020 HLG) 2K] are selected in [Type] [Automatic].
  • Page 40 OSD Menu Sub Menu Setting Options Single Input Dual View Automatic, Off When other than [Image Division] [Multi View (Quad)] or [Multi View (Dual)] The image from the input signal can be reduced and shown in dual-screen. [Automatic]: When the [Picture Function Settings] Sub Menu items are set to [On], identical images are automatically shown and dual-screen comparison can be made. 4K images are shown in reduced size. Relevant [Picture Function Settings] Sub Menu items: [Peaking], [False Color], [Range Check], [2020 Outside of Gamut View], [Monochrome], [Blue Only], [Red Off], [Green Off], [Blue Off], and [Compare View] • Cannot be used when an unsupported video signal is input. • Cannot be set when [Input Configuration] is set to [HD/SD-SDI]. Separator White In the following cases, screen borders will be displayed. Half - When [Multi View (Quad)] or [Multi View (Dual)] is selected Black - When [Single Input Dual View] is set to [Automatic] and the images are shown next to each other for image comparison - When [Picture Function Settings] [Compare View] [Enable] is [On]...

  • Page 41: Display Settings

    OSD Menu Display Settings This menu is used to configure the display method. Sub Menu Setting Options (Bold: factory default) Screen Scaling Native Input Resolution Defines how the video is scaled and displayed on the screen. 200% Automatic [Native Input Resolution]: Displays the input signal without scaling. 1920x1080 (original) [200%]: Doubles the vertical and horizontal dimensions. 1920x1080→3840x2160 [Automatic]: Fits size to fill screen. 1920x1080→3840x2160 4096×2160→3840×2025 • In the following cases, the maximum magnification is 200% even if [Automatic] is selected. - When [Peaking], [False Color], or [Range Check] [Enable] is set to an option other than [Off] • In the following cases, images are shown in reduced size when [Automatic] is selected. When the resolution is [4096×2160] When the resolution is [2048×1080]: When [Image Division] [Multi View (Quad)] or [Multi View (Dual)] is selected Anamorphic x2.0 Set when checking images photographed using an anamorphic lens.
  • Page 42 OSD Menu Sub Menu Setting Options (Bold: factory default) Aspect (SD-SDI) Automatic Sets the size for displaying SD-SDI signal images. 16:9 [Automatic]: Automatically determined based on payload. [16:9]: Images are displayed with an aspect ratio of "16:9". [4:3]: Images are displayed with an aspect ratio of "4:3". • When the following functions are activated, [4:3] is selected. Peaking False Color Range Check Video Position When using [Multi View (Quad)], [Multi View (Dual)], or [Single Input Dual Middle (Multi View) View] Center Sets the vertical display position for the image. [Top]: Displays at the top of the screen. [Middle]: Displays at the top middle of the screen. [Center]: Displays at the middle of the screen. Zoom Enlarges part of the video image. The zoom function can be used when the resolution is [4096x2160], [3840x2160], [2048x1080] or [1920x1080]. • The zoom function cannot be used in the following cases: - During execution of [Playback File] under [Screen Capture] - During display of the test pattern When [Multi View (Quad)], [Multi View (Dual)] or [Single Input Dual View] is selected When [Channel Settings] [Input Configuration] [HD/SD-SDI] - When [Picture Function Settings] [Compare View] [Enable] is set to [On]...
  • Page 43 OSD Menu Sub Menu Setting Options (Bold: factory default) I/PsF Automatic Defines how the interlace signal or PsF signal is displayed. Interlace [Automatic]: Automatically determined based on payload and displayed. If there is no payload, the signal is displayed as an interlace signal. [Interlace]: Displayed as an interlace signal. [PsF]: Displayed as a PsF signal. Automatic I/P Conversion Select the interlaced signal I/P conversion method. Normal [Automatic]: In this mode, video and still image are determined, and conversion corresponding to the type of image is automatically performed. [Normal]: In this mode, video and still image are not determined, and predetermined conversion processing is performed.

  • Page 44: Audio Settings

    OSD Menu Audio Settings This menu is used to set audio output. Sub Menu Setting Options (Bold: factory default) CH L (SDI) CH1 to CH16 (CH1) Sets the audio to be output from the two channels (L/R) of the headphone respectively. CH R (SDI) CH1 to CH16 (CH2) CH L (HDMI) CH1 to CH8 (CH1) CH R (HDMI) CH1 to CH8 (CH2) Volume (speaker) 0 to 100 (30) Sets the volume of the speaker or headphone/AUDIO OUT terminal. (Increments of 1) • When the headphone is connected to the headphone terminal, output from the speaker stops. Volume ( / AUDIO OUT) • The AUDIO OUT terminal can be used at the same time as the speaker. • The volume of the headphone and AUDIO OUT terminal is the same.

  • Page 45: Marker Settings

    OSD Menu Marker Settings This menu is used to configure various markers. The factory defaults differ according to the [Marker Preset] setting 50). Sub Menu Setting Options (Factory default) Marker Preset Marker 1 to 5 Customizes markers which are assigned to markers 1 to 5. Aspect Marker [Aspect Marker] displays a range in accordance with the specified aspect ratio. Enable On, Off Switches the aspect marker On, Off. Mask Black Switches the mask color. Mask is the blanking area outside the range of Half the marker. [Black]: [Half] (50% gray): [Off]: Turns mask off. Aspect Ratio 16:9, 15:9, 14:9, 13:9, Sets the aspect ratio of the aspect marker. 4:3, 2.39:1, 2.35:1, The aspect ratio can be entered as a numeric value when you select 1.896:1, 1.85:1, 1.66:1, [Variable] (0.01:1 increments). The grayed out slider becomes active and Variable can be used to set the aspect ratio. • When Variable is selected 1.00:1 to 3.00:1 Line On, Off...
  • Page 46 OSD Menu Sub Menu Setting Options (Factory default) Line Color White, Red, Green, Sets the color of the aspect marker line. Blue, Yellow, Cyan, Magenta, Gray Line Brightness High, Low, Half Sets the brightness of the aspect marker line. Safety Zone Marker 1, 2 There are two types of [Safety Zone Marker]: 1 and 2, which share the same settings. A safety zone marker is used to set the safe zone of the image (actual displayed area) to check the image. Enable On, Off Switches the safety zone marker On, Off. Aspect Ratio 16:9, 15:9, 14:9, 13:9, Sets the aspect ratio of the safety zone marker. 4:3, 2.39:1, 2.35:1, 1.896:1, 1.85:1, 1.66:1, [Variable]: The aspect ratio can be entered as a numeric value (0.01:1 Variable increments). The grayed out slider becomes active and can be used to set the aspect ratio. • When Variable is • When [Area Size] is set to [Variable (dot)], you cannot select [Aspect Ratio]. selected 1.00:1 to 3.00:1 Area Size 80%, 85%, 88%, 90%, Sets the safety zone marker area size. 93%, 95%, Variable (%), Variable (dot) [Variable (%)]: The grayed out [Rate (%)] becomes active.
  • Page 47 OSD Menu Sub Menu Setting Options (Factory default) Shape Sets the area shape of the safety zone marker. Box (Mask) Brackets [Box]: Enclosure [Box (Mask)]: [Brackets]: [Enclosure]: Line Width Thick Sets the width of the safety zone marker line. Normal Thin Line Color White, Red, Green, Sets the color of the safety zone marker line. Blue, Yellow, Cyan, Magenta, Gray Line Brightness High, Low, Half Sets the brightness of the safety zone marker line. H Position -1920 to 1920 Adjusts the marker horizontal position with the set aspect and size (in increments of 2). V Position -1080 to 1080 Adjusts the marker vertical position with the set aspect and size (in increments of 2).
  • Page 48 OSD Menu Sub Menu Setting Options (Factory default) Area Marker1, 2 There are two types of [Area Marker]: 1 and 2, which share the same settings. [Area Marker] is used to check a specific area using a rectangular box. Enable On, Off Switches the area marker On, Off. H Position 0 to 3830 Sets the start position (x-coordinate) to draw the rectangle (in increments of 2). V Position 0 to 2150 Sets the start position (y-coordinate) to draw the rectangle (in increments of 2). Width (dot) 10 to 3840 Sets the width of the rectangle (in increments of 2). Height (dot) 10 to 2160 Sets the height of the rectangle (in increments of 2). Mask Black Switches the mask color (in the marker). Half Line On, Off When [Mask] [Black] or [Half] Turns On/Off the outlines of the rectangular box. Line Width Thick When [Mask] [Off] or [Line] [On] Normal Sets the width of the area marker line.
  • Page 49 OSD Menu Sub Menu Setting Options (Factory default) Center Marker [Center Marker] shows the center of the image. Enable On, Off Switches the center marker On, Off. Size Large Sets the size of the center marker. Middle Small Line Width Thick Sets the width of the center marker line. Normal Thin Line Color White, Red, Green, Sets the color of the center marker line. Blue, Yellow, Cyan, Magenta, Gray Line Brightness High, Low, Half Sets the brightness of the center marker line. Grid Marker [Grid Marker] is marker used to check the horizontal and vertical position. When [Distance] [*** dots] When [Distance] [***% (UHD)] Enable On, Off Switches the grid marker On, Off.
  • Page 50 OSD Menu The marker is not displayed in the following cases: - When there is no signal, unsupported signal, or a channel with [Input Configuration] not set is selected - When an enlarged image is displayed - During the execution of [Playback File] under [Screen Capture] - When a [Test Pattern] is displayed - When using [Multi View (Quad)], [Multi View (Dual)], or [Single Input Dual View] The marker is not displayed in the following cases: - When an enlarged image is displayed - When using [Multi View (Quad)], [Multi View (Dual)], or [Single Input Dual View] The marker is not displayed in the following cases: - When an enlarged image is displayed ■ Details of the factory default settings for marker preset Factory default Item Marker 1 to 4 Marker 5 Aspect Marker Enable Mask...
  • Page 51 OSD Menu Factory default Item Marker 1 to 4 Marker 5 Area Marker 1, 2 Enable H Position 240 (3500**) V Position 120 (60**) Width (dot) Height (dot) 120 (240**) Mask Half Line Line Width Normal Normal Line Color White Gray Line Brightness Half Center Marker Enable Size Middle Small Line Width Normal Normal Line Color White White Line Brightness...

  • Page 52: Function Settings

    OSD Menu Function Settings This menu is used to set the image signal information display and the cinema camera link function. Sub Menu Setting Options (Bold: factory default) Time Code Display the time code superimposed on the signal. VITC  01:23:45.05 Enable On, Off Switches the time code display On, Off. Type VITC Selects the type. • This setting becomes invalid when HDMI signal is input and is fixed to [VITC]. VITC Field Flag On, Off Select whether or not to use the field flag when the VITC time code is displayed. Size Large Selects the size. Small Position Top Left Selects the display position. Top Right • When [Multi View (Dual)] or [Multi Information View] is selected, this setting is Bottom Left invalid. Bottom Right • When [Top Left] or [Top Right] is selected: When set to [Audio Level Meter] [Enable] [On], the time code will not be...
  • Page 53 OSD Menu Sub Menu Setting Options (Bold: factory default) Normal Channel Order Sets the order of channels. Grouping [Normal]: Odd-numbered channels are shown on the left side, even- numbered channels on the right side “([1, 3, 5, 7] etc.) on the left, ([2, 4, 6, 8] etc.) on the right”. [Grouping]: Channels are shown in sequence on the left and right sides “([1, 2, 3, 4] etc.) on the left, ([5, 6, 7, 8] etc.) on the right”. Large Size Sets the size of the display. Small • When [Channel Number (SDI)] is [16CH], and [Single Input Dual View] or [Multi Information View] is selected, this setting is invalid. Position Normal Selects the display position. Left [Normal]: Displays the audio level meter on both ends. [Left]: Indication on the right side is displayed toward the center of the screen. This prevents the indication from overlapping with the banner. • When [Multi Information View] is selected, this setting is invalid. Peak Hold On, Off One second of audio signal at the peak is kept. Reference Level -40 to 0 (-20) Sets the reference level. Brightness Normal Sets brightness for the audio level meter.
  • Page 54 OSD Menu Sub Menu Setting Options (Bold: factory default) Automatic Sets the scale of the wave form monitor. Scale SMPTE ST 2084 (PQ) [Automatic]: Sets in accordance with the [Gamma/EOTF] and [Color Hybrid Log-Gamma Range] settings. Canon Log • When [SMPTE ST 2084 (PQ)], [Canon Log], [Canon Log 2], or [Canon Log 3] is Canon Log 2 set (including [Automatic]): Canon Log 3 When [Gamma/EOTF] [SMPTE ST 2084 (PQ)], the item is displayed in S-Log2 accordance with the [Color Range] settings ([SDI Full (4-1019)] is set to [Full]). S-Log3 ARRI (Rec2100-PQ- 1K-100) ARRI (Rec2100-HLG- 1K-200) Reference Line 4 to 1023 A guide is displayed at the specified position. [Reference Line] is not displayed when [1023] is selected. Reference Level Automatic Sets the range of the reference level. Tints the outside of the range of the Manual reference level.
  • Page 55 OSD Menu Sub Menu Setting Options (Bold: factory default) Vector Scope Configures various settings for the vector scope. Vector scope displays the intensity of color signals and hue with the horizontal axis showing the color difference signal Cb and the vertical line showing (Cb, Cr) = (255, 255) Magenta Yellow Blue Green Cyan (Cb, Cr) = (0, 0) Enable On, Off Switches the vector scope On, Off. Target Sets the target. 100% 75%+100% Position Selects the display position. Bottom Left • When [Multi View (Dual)] or [Multi Information View] is selected, this setting is Bottom Right invalid. Bottom Left Bottom Right Size Sets the size of the display. Large, Middle, Small • When [Multi Information View] is selected, this setting is invalid.
  • Page 56 OSD Menu Sub Menu Setting Options (Bold: factory default) x1, x2, x3 Gain Increases the displayed graph size. HDR Range On, Off [On]: Areas that exceed the HDR range will be tinted. [Off]: Areas that exceed the HDR range will not be tinted. HDR/SDR Ratio On, Off Switches between displaying or not displaying the [HDR/SDR Ratio] when [Gamma/EOTF] is set to [SMPTE ST2084 (PQ)] or [Hybrid Log-Gamma]. Peak/Ave. Luminance On, Off Switches between displaying or not displaying the [Peak/Ave. Luminance] when [Gamma/EOTF] is set to [SMPTE ST2084 (PQ)] or [Hybrid Log- Gamma]. Size Large, Small Sets the size of the display. • When [Single Input Dual View] or [Multi Information View] is selected, this setting is invalid. Frame Luminance Monitor When [Gamma/EOTF] is set to [SMPTE ST 2084 (PQ)] or [Hybrid Log-Gamma], [Max./Ave. Luminance] for the entire screen (frame) is displayed. For other conditions, [Max./Ave. Gradation Values] is displayed. The frame luminance monitor can be used when the resolution is [4096x2160], [3840x2160], [2048x1080] or [1920x1080]. Current value for average luminance (cumulative maximum value) Current value for peak luminance (cumulative maximum value) Peak luminance Average luminance • Luminance graph...
  • Page 57 OSD Menu Sub Menu Setting Options (Bold: factory default) Enable On, Off Sets [Frame Luminance Monitor] on or off. Obtains the luminance value when valid. Display Sets whether each graph is displayed. Luminance Graph HDR/SDR Ratio Graph [All]: Displays [Luminance Graph (Including luminance value)] and [HDR/ Luminance Value SDR Ratio Graph]. [Luminance Graph]: Displays [Luminance Graph]. [HDR/SDR Ratio Graph]: Displays [HDR/SDR Ratio Graph (Including luminance value)]. [Luminance Value]: Displays the peak and average luminance values. [Off]: Does not display any graphs. Luminance Graph Sets [Luminance Graph] display method. Settings Luminance On, Off Switches between displaying and not displaying the luminance distribution Distribution graph. Reference Automatic [Automatic]: Works in conjunction with the [HDR Range] settings to Luminance Level - Manual automatically tint the areas that exceed the peak luminance. Peak [Manual]: Sets the upper limit for peak luminance. Areas that exceed the • When Manual is set value will be tinted.
  • Page 58 OSD Menu Sub Menu Setting Options (Bold: factory default) Pixel Value Check Measures and displays the RGB value of the specified pixel (cursor) position. When [Gamma/EOTF] is set to [SMPTE ST 2084 (PQ)] or [Hybrid Log-Gamma], the brightness value is also displayed. • The non-constant value is displayed even if [2020 Constant Luminance] is set to [Constant]. Enable On, Off Switches the pixel value check On, Off. H Position 1 to 4096 (960) Sets the pixel position (horizontal). V Position 1 to 2160 (540) Sets the pixel position (vertical). Reset Position Normal Sets operation when the RESET button is pressed. Around Peak Luminance [Normal]: Resets the value to the default value. [Around Peak Luminance]: Moves closer to the area of peak luminance inside the display image. Chromaticity Diagram On, Off Switches the chromaticity diagram On, Off. [On]: Displays the chromaticity diagram. The chromaticity diagram is displayed only when [Color Gamut] and [Gamma/EOTF] are set as shown below. ž [Color Gamut]: ITU-R BT.2020, ITU-R BT.709 ž [ Gamma/EOTF]: 1.0, 2.2, 2.35, 2.4, 2.6, SMPTE ST 2084 (PQ), Hybrid Log-Gamma Multi Information View On, Off...
  • Page 59 OSD Menu Sub Menu Setting Options (Bold: factory default) Signal Monitoring Monitors the input signal status. • [Signal Monitoring] cannot be used in the following cases: - When [Single Input Dual View] is displayed - When an enlarged image is displayed - During display of the test pattern - During execution of [Playback File] under [Screen Capture] - When [Channel Settings] [Input Configuration] [Multi View] - When [Function Settings] [Multi Information View] • When an error is displayed, [In Monitor Display] will not be shown. • The position the error is displayed can be adjusted with [In Monitor Display] [Position]. Control On, Off Sets whether [Signal Monitoring] is used or not. Error Hold On (No time out) Sets the length of time for displaying errors, when they are detected. On (5 sec.) [On (No time out)]: Errors continue to be displayed. To hide the displayed error, press the RESET button when closing the OSD menu.
  • Page 60 Rec2100-PQ-1K-100 When [Automatic Adjustment (ARRI)] [On] Rec2100-HLG-1K-200 Sets the color gamut and gamma/EOTF shown in the display. 3D-LUT 1-8 Automatic Adjustment When [Picture Mode] [User 6] to [User 7], [Input Configuration] [12-3G/HD-SDI] (VARICAM) Sets whether or not to link to the camera's image quality setting. On, Off Refer to the Setting Values Correspondence Table. ( User LUT V-Log to V-709 When [Automatic Adjustment (VARICAM)] [On] 3D-LUT 1-8 Sets the color gamut and gamma/EOTF shown in the display. Anamorphic On, Off When a Canon camera is connected, displays in accordance with the settings when anamorphic lens display settings are included in the camera metadata. This is executed when [Channel Settings] [Input Configuration] [12-3G/HD-SDI] is selected. Camera Information Automatic Camera information display is set when [Channel Settings] [Input Configuration] [12-3G/HD-SDI] is selected. [Automatic]: Camera information is displayed for 4 seconds when the information has changed. [On]: Camera information is always displayed. [Off]: Camera information is not displayed.
  • Page 61 OSD Menu T he information display functions that can be displayed vary depending on the video display's settings or the input signal status. Audio Wave Frame Pixel Multi Time Vector Chromaticity Level Form Histogram Luminance Value Information Code Scope Diagram Meter Monitor Monitor Check View When [Frame Hold] is [On] — — — During execution of [Playback File] — — — — — — — — — under [Screen Capture] When [Test Pattern] is displayed —...
  • Page 62 OSD Menu ■ Parameter of Cinema EOS cameras and Canon displays Cinema EOS cameras Canon display Color Space Color Gamut Color Temperature BT.709 ITU-R BT.709 BT.2020 ITU-R BT.2020 DCI-P3 DCI-P3 DCI-P3 Cinema Gamut Cinema Gamut to 709 Cinema Gamut to 2020 Cinema Gamut to DCI DCI-P3 Cinema EOS cameras Canon display Gamma/EOTF Gamma/EOTF HDR Range Canon Log Canon Log (HDR) Canon Log 2 Canon Log 2 (HDR) — Canon Log 3...
  • Page 63 OSD Menu ■ Parameter of ARRI Cinema camera and Canon displays ARRI Cinema camera Canon display Color Space Display Color CDL/User LUT Color Gamut Gamma/EOTF HDR Range Gamut REC 709 — — ITU-R BT.709 — REC 2020 — — ITU-R BT.2020 — Wide Gamut Log C Rec2100-PQ- ARRI (Rec2100- ITU-R BT.2020 SMPTE ST 2084 1000 1K-100 PQ-1K-100) (PQ) Rec2100-HLG- ARRI (Rec2100- ITU-R BT.2020...

  • Page 64: Picture Function Settings

    OSD Menu Picture Function Settings This menu is used to set video assistance functions, for example. Sub Menu Setting Options (Bold: factory default) Peaking The outline is displayed in a color, used to check the focus. Customizes peakings which are assigned to Peaking 1 or Peaking 2. Enable Peaking 1 Switches the peaking display mode and also sets peaking to Off. Peaking 2 Monochrome When [Peaking 1] Displays video in monochrome. On, Off When [Peaking 2] On, Off Frequency When [Peaking 1] Sets the central frequency of contour enhancement signals. Low, Middle, High When [Peaking 2] Low, Middle, High Range -3 ~ 3 (0) Sets the width of the range to be colored. Color White, Red, Green, Sets the color to be used. Blue, Yellow, Cyan, Magenta False Color Displays different colors for the video's brightness levels to make it easier to check the exposure and brightness distribution. Customizes the false color and sets it to false color 1 or false color 2.
  • Page 65 OSD Menu Sub Menu Setting Options (Bold: factory default) Sets the tint color range. Range - HDR When [False Color 1] Automatic Automatic (Over Range) [Automatic]: Sets the upper limit automatically in accordance with the Manual [Gamma/EOTF] settings. When [False Color 2] Automatic When [Manual] or [Automatic (Over Range)] is selected, sets the size of Automatic (Over Range) the area to be colored. Manual Range Check Displays video in monochrome, with the areas where the set range is exceeded are shown tinted. Customizes Range Check and sets it to Range Check 1, 2. Enable Range Check 1 Switches the Range Check display mode On, Off. Range Check 2 Over Range Automatic, Manual Displays video in monochrome, with the areas where the set range is exceeded are shown tinted. [Automatic]: Outside the range of the [Color Range] settings is tinted. When [Gamma/EOTF] [SMPTE ST 2084 (PQ)] or [Hybrid Log- Gamma], outside the range of the [Color Range] and [HDR Range] settings is tinted. [Manual]: Only areas that exceed the range set at [SMPTE ST 2084 (PQ)] or [Hybrid Log-Gamma] are tinted.
  • Page 66 Sets Comparison mode On or Off. Type Automatic Sets the type of the image to compare. HDR/SDR CDL/User LUT [Automatic]: [HDR/SDR] when [Adjustment] [CDL/User LUT] is [Off], otherwise set at [CDL/User LUT]. [HDR/SDR]: HDR and SDR images are displayed. [CDL/User LUT]: The image on which [CDL] or [User LUT] is applied is displayed only in the left screen. • Not settable in the following cases: When [Color Gamut] is set to [Cinema Gamut to XXX] or [S-GamutXXX] When [Gamma/EOTF] is set to [Canon Log], [Canon Log 2] or [Canon Log 3] HDR/SDR Convert 2020 HDR to 709 SDR When [Type] is set to [HDR/SDR] or [Automatic ([HDR/SDR])] Method 2020 HDR to 2020 SDR Sets the display method of the screen set to SDR. User LUT 1-User LUT 8 [2020 HDR to 709 SDR], [2020 HDR to 2020 SDR]: Setting differs according to the [Gamma/EOTF] settings. [SMPTE ST 2084 (PQ)]: The [User LUT] corresponding to each setting is applied. [Hybrid Log-Gamma]: The [User LUT] corresponding to each setting is applied. [Canon Log(HDR)], [Canon Log 2(HDR)], [Canon Log 3(HDR)]: [Canon Log], [Canon Log 2] or [Canon Log 3] is applied. [S-Log2 (HDR)], [S-Log3 (HDR)]: [HDR Range] setting [100] is set. [User LUT 1-8]: The specified [User LUT] is applied. After applying [User LUT] the adjustment inside the display fixes [Color Gamut] at [ITU-R BT.709] and [Gamma/EOTF] at [2.4]. [Off]: Only brightness is lowered.
  • Page 67 OSD Menu Sub Menu Setting Options (Bold: factory default) Luminance (SDR) 50.0 to 200.0 (100.0) When [Type] is set to [HDR/SDR] or [Automatic ([HDR/SDR])] Sets the luminance of the SDR side. Color Temperature Normal, When [Type] is set to [HDR/SDR] or [Automatic ([HDR/SDR])] (SDR) D93, D65, Sets the SDR color temperature. D65 Custom, DCI-P3 Gain (SDR) -15 to 15 (0) When [Type] is set to [HDR/SDR] or [Automatic ([HDR/SDR])] Sets the SDR gain. User LUT Target 1 User LUT 1 to When [Type] is set to [CDL/User LUT] or [Automatic ([User LUT])] Target 2 (Quad) User LUT 8, Off Sets the comparison target. Target 3 (Quad) [Target 2 (Quad)], [Target 3 (Quad)]: When [Multi View (Quad)] is displayed, the User LUT is applied to each quarter of the screen for Compare View. • [Peaking], [False Color], [Range Check], [2020 Outside of Gamut View], [Compare View]: Operation in accordance with the configuration of the video display 2020 Outside of Peaking False Color Range Check...

  • Page 68: Network/Imd Settings

    Adjustment Settings are linked between displays connected via LAN. This device's Channel setting values are applied to all linked displays. Adjustment/Channel * Before linking settings, check that the following conditions are met. Off a Turn on the power to this display and the display(s) to link with, and check that they are all recognized on the network b Change the adjustment or channel and check that the other display(s) also change The devices and firmware versions that can be linked are shown below. DP-V1830: Version 1.1 or higher DP-V2730: Version 1.0 or higher Displays not connected can be removed with the RESET button. • Operating the buttons on this display will reflect setting value changes in all. Linked operations using Payload ID, HDMI, Camera, etc. will not reflect the settings changes. • If a display model has functions with different menu settings or setting ranges, some settings will not be correctly exported (settings will not be changed, will revert to factory defaults, etc.) • In an environment where communication cannot be done properly, such as when the network environment is unstable or the bandwidth is insufficient, settings may not link properly. Only connect displays to be controlled to the LAN. If a Display Controller is connected, it may not operate properly. • If the setting of the display to link with is [Picture Mode] [Type] [Quad] or [Dual], it may not operate.
  • Page 69 OSD Menu Sub Menu Setting Options (Bold: factory default) In Monitor Display The video display supports Television Systems Ltd.’s “TSL UMD Protocol Ver. 5.0”. You can operate the video display using an external device connected to the LAN terminal and display characters and tally lights on the screen. You can input any characters you like directly from this video display ( 17). When [Function Settings] [Multi Information View] [On] is selected, they are not displayed. Control TSL Ver. 5.00 Sets whether or not to receive the control signal from the connected Manual device. [Manual]: Select to input the characters on this video display. Does not receive a control signal from the connected device. Position This sets whether the characters and tally lights will be displayed at the Bottom top or the bottom. Manual Display Type Automatic [Automatic]: Changes display in accordance with the Input Configuration. Single [Single]: Single-screen display. Dual A,B, Dual C,D [Dual A,B], [Dual C,D]: Dual-screen display. Quad A,B,C,D [Quad A,B,C,D]: Quadruple-screen display. • When [Function Settings] [Signal Monitoring] [Control] is set to [On] then [Manual Display Type] is fixed to [Automatic].

  • Page 70: System Settings

    OSD Menu System Settings This menu is used to configure system settings related to the video display. Sub Menu Setting Options (Bold: factory default) Function/Channel Button Sets the function or channel to assign to the F buttons or CH button. Function Button Sets the function to assign to the F buttons of the main unit ( 13). Select an F button and assign a function from the following list ( 74). Function Button (ALT) Channel Button Sets the channel to assign to the CH button on the display. CH1 to CH20 (CH1) Select a CH button and register a channel number. A list of settings under the menu [Channel Settings] ( 36) is displayed. CH1 to CH20 (CH2) CH1 to CH20 (CH3) You can operate the video display using an external controller such as a switcher that has been connected to the GPI terminal. Operates by connecting (shorting) the GND (No. 8 Pin) to No.s 1 to 7. • This function will not work correctly in the following cases. - If the same function is assigned to multiple pins. If the changes to this menu item setting and the pin assignments were made when the pins were shorted Type Level, [Level]: Operates while shorted. Short Edge [Short Edge]: Switches between “operate”/”do not operate” for each short.
  • Page 71 OSD Menu Sub Menu Setting Options (Bold: factory default) Display Name Sets the name of the main unit. You can input up to 16 alphanumeric characters. OSD Settings Banner Sets the banner display method for the channel name, signal information, and status of the video display. Automatic Display On, Off Automatically displays the banner when the input signal or picture mode are changed. Picture Mode On, Off Sets whether to display [Picture Mode]. Time Out On, Off The banner automatically disappears. On, Off Function Button Guide [On]: When all OSD are hidden, you can display the list of functions assigned to an F button on the video display by operating the jog dial. [Off]: Function Button Guide is not displayed. OSD Brightness Automatic Sets the brightness of the OSD. (High - Middle) Automatic The brightness is automatically adjusted to suit the luminance when (High - Low) [Automatic] is selected. You can choose between [High - Low] and High [High - Middle] adjustment ranges.
  • Page 72 Setting Options (Bold: factory default) Power Indicator/Button LED Settings Power Indicator Adjusts the brightness of the power indicator on the main unit. The greater Brightness 1 to 5 (3) the number, the higher the brightness. Display Button LED On, Off Sets the F buttons and the lamp on the face. Button Name Lighting Always, 60 sec., Sets the time (sec) until the lamp on the face goes out, if no operation is Time 30 sec., 10 sec., 5 sec. performed. [Always]: The lamp on the face is always lit. Firmware/License Update This function is used to update the video display firmware. Refer to the Canon website for detailed information. Export/Import Sets the export/import OSD menu settings. Export Target Select the export destination. User 1 to User 3 [USB]: Export to a USB memory. [User 1] to [User 3]: Export to the built-in memory of the main unit. [LAN]: Exports to a display connected via LAN. Filename When [Target] [USB] Factory default is "dinfo_dpv****.dat" (****: number of the product name). You can change the name of the file to be exported to the USB memory within 16 one-byte characters including alphabetical characters, numbers, and symbols. Execute Performs export.
  • Page 73 OSD Menu Sub Menu Setting Options (Bold: factory default) Last memory Power on Setting You can select the state of the display when the power is turned on. User 1 to User 3 [Last memory]: Launches with the same settings as when the power was turned off the previous time. [User 1] to [User 3]: It starts up with the settings saved in [User 1] to [User 3] under [Export]. Reset All Settings Returns all settings to factory default. When selected, the message [Reset Cancel all settings to factory defaults?] appears. [OK]: Performs reset. [Cancel]: Returns to the previous screen without resetting. • The following settings cannot be exported or imported. Adjustment CDL/User LUT Bypass Zoom Preset, Frame Hold Display Settings Audio Settings Audio Mute Test Pattern Function Settings Picture Function Settings Peaking (Enable), False Color (Enable), Range Check (Enable), 2020 Outside of Gamut View (Enable), Monochrome, Blue Only, Red Off, Green Off, Blue Off, Compare View (Enable) Network/IMD Settings...
  • Page 74 OSD Menu ■ Function to allow registration for the display F buttons ( Item Options Item Options Adjustment Picture Mode Channel Settings Channel List Luminance Select Input Signal Brightness Audio Input Chroma Single Input Dual View Chroma Up Switch Out (SDI Input A) ~ Switch Out (SDI Input D) Backlight Control HDR Range CH1 to CH20 Gain Display Settings Screen Scaling Bias Anamorphic Zoom Preset Picture Mode ITU-R BT.709 Zoom 1 ITU-R BT.2020...
  • Page 75 OSD Menu Item Options Function Settings TC/ALM Time Code Audio Level Meter WFM/VEC Wave Form Monitor WFM Select Signal Vector Scope Histogram/Frame Luminance Histogram Frame Luminance Monitor Chroma Diagram/Pixel Value Chromaticity Diagram Pixel Value Check Multi Information View Signal Monitoring Log Capture Camera Information Picture Function Settings Peaking Peaking 1 Peaking 2 False Color False Color 1 False Color 2 Range Check Range Check 1 Range Check 2 2020 Outside of Gamut View Monochrome Blue Only Red Off Green Off Blue Off Compare View System Settings Signal Information Hide OSD The chroma value is set to 2000.

  • Page 76: Signal Information

    OSD Menu Signal Information Shows the signal information. When [Select Input Signal] is [Quad Input], information for the entire signal and each input is displayed. Select a signal with the jog dial according to the guide at top right corner of the menu. When signal information has been obtained although it is not displayed on the screen, the content of the information is grayed out. SDI Signal HDMI Signal Item Display Example Item Display Example Channel Channel Input Configuration 12-3G/HD-SDI (3G-A) Input Configuration HDMI Select Input Signal Quad Input Format Automatic Image Division Automatic Resolution 4096x2160 Picture Rate, I/P/PsF Format Automatic 60.00P Resolution 4096x2160 Pixel Encoding, Color Depth 4:2:2 YCbCr 10-bit Picture Rate, I/P/PsF* 24.00P Matrix ITU-R BT.709...

  • Page 77: Supported Signal Format

    Supported Signal Format Transmission method Signal format Color format Color depth Standards SD-SDI 720x487i 59.94 Hz* 4:2:2 YCbCr 10-bit SMPTE-259M 720x576i 50 Hz HD-SDI 1280x720P 59.94/60.00 Hz 4:2:2 YCbCr 10-bit SMPTE 292-1 SMPTE 296 1280x720P 50.00 Hz 1280x720P 29.97/30.00 Hz 1280x720P 25.00 Hz 1280x720P 23.98/24.00 Hz 1920x1080i 59.94/60.00 Hz SMPTE 292-1 SMPTE 274M 1920x1080i 50.00 Hz 1920x1080P 29.97/30.00 Hz 1920x1080PsF 29.97/30.00 Hz 1920x1080P 25.00 Hz 1920x1080PsF 25.00 Hz 1920x1080P 23.98/24.00 Hz 1920x1080PsF 23.98/24.00 Hz 2048x1080P 29.97/30.00 Hz SMPTE 292-1 SMPTE 428-9 2048x1080PsF 29.97/30.00 Hz SMPTE 428-19 2048x1080P 25.00 Hz SMPTE 2048-2...
  • Page 78 Supported Signal Format Transmission method Signal format Color format Color depth Standards 3G-SDI 1920x1080i 59.94/60.00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 (Level A) 4:4:4 YCbCr SMPTE 274M 4:2:2 YCbCr 12-bit 1920x1080P 50.00 Hz 4:2:2 YCbCr 10-bit 1920x1080i 50.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 1920x1080P 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 1920x1080PsF 29.97/30.00 Hz 4:4:4 RGB 10-bit 12-bit 4:4:4 YCbCr 12-bit...
  • Page 79 Supported Signal Format Transmission method Signal format Color format Color depth Standards 3G-SDI 2048x1080P 47.95/48.00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 (Level A) SMPTE 2048-2 2048x1080P 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 428-9 SMPTE 428-19 4:4:4 X'Y'Z' 12-bit SMPTE 2048-2 4:4:4 YCbCr 12-bit/10-bit SMPTE 425-1 SMPTE 2048-2 4:2:2 YCbCr 12-bit 2048x1080PsF 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 428-9 4:4:4 X'Y'Z' 12-bit SMPTE 428-19 SMPTE 2048-2...
  • Page 80 Supported Signal Format Transmission method Signal format Color format Color depth Standards 3G-SDI 1920x1080P 59.94/60.00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 (Level B) SMPTE 372 1920x1080i 59.94/60.00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 274M 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 1920x1080P 50.00 Hz 4:2:2 YCbCr 10-bit 1920x1080i 50.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 1920x1080P 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 1920x1080PsF 29.97/30.00 Hz 4:4:4 RGB...
  • Page 81 Supported Signal Format Transmission method Signal format Color format Color depth Standards 3G-SDI 2048x1080P 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 (Level B) SMPTE 372 SMPTE 428-9 4:4:4 X'Y'Z' 12-bit SMPTE 428-19 SMPTE 2048-2 4:4:4 YCbCr 12-bit/10-bit SMPTE 425-1 SMPTE 372 4:2:2 YCbCr 12-bit SMPTE 2048-2 2048x1080PsF 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 372 4:4:4 X'Y'Z' 12-bit SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2 4:4:4 YCbCr 12-bit/10-bit...
  • Page 82 Supported Signal Format Transmission method Signal format Color format Color depth Standards 3G-SDI 2048x1080PsF 23.98/24.00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 (Level B) SMPTE 372 4:4:4 X'Y'Z' 12-bit SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2 4:4:4 YCbCr 12-bit/10-bit SMPTE 425-1 SMPTE 372 4:2:2 YCbCr 12-bit SMPTE 2048-2 Dual Link 3G-SDI 3840x2160P 29.97/30.00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-3 2 Sample Interleave SMPTE 372 3840x2160P 25.00 Hz (Level B) SMPTE 274M 3840x2160P 23.98/24.00 Hz 4096x2160P 29.97/30.00 Hz...
  • Page 83 Supported Signal Format Transmission method Signal format Color format Color depth Standards Quad Link 3G-SDI 3840x2160P 59.94/60.00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 (Level A) SMPTE 274M 3840x2160i 59.94/60.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 3840x2160P 50.00 Hz 4:2:2 YCbCr 12-bit 3840x2160i 50.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 3840x2160P 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 3840x2160PsF 29.97/30.00 Hz 4:4:4 RGB 10-bit...
  • Page 84 Supported Signal Format Transmission method Signal format Color format Color depth Standards Quad Link 3G-SDI 4096x2160P 50.00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 (Level A) SMPTE 2048-2 4096x2160P 47.95/48.00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-1 SMPTE 2048-2 4096x2160P 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 428-9 4:4:4 X'Y'Z' 12-bit SMPTE 428-19 SMPTE 2048-2 4:4:4 YCbCr 12-bit/10-bit SMPTE 425-1 SMPTE 2048-2 4:2:2 YCbCr 12-bit 4096x2160PsF 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1...
  • Page 85 Supported Signal Format Transmission method Signal format Color format Color depth Standards Quad Link 3G-SDI 3840x2160P 59.94/60.00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-5 2 Sample Interleave SMPTE 274M 3840x2160P 50.00 Hz 4:2:2 YCbCr 10-bit (Level A) 3840x2160P 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 3840x2160P 25.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 3840x2160P 23.98/24.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 4096x2160P 59.94/60.00 Hz 4:2:2 YCbCr...
  • Page 86 Supported Signal Format Transmission method Signal format Color format Color depth Standards Quad Link 3G-SDI 3840x2160i 50.00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 (Level B) 4:4:4 YCbCr SMPTE 372 SMPTE 274M 4:2:2 YCbCr 12-bit 3840x2160P 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 3840x2160PsF 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 3840x2160P 25.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 3840x2160PsF 25.00 Hz 4:4:4 RGB...
  • Page 87 Supported Signal Format Transmission method Signal format Color format Color depth Standards Quad Link 3G-SDI 4096x2160P 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 (Level B) SMPTE 372 SMPTE 428-9 4:4:4 X'Y'Z' 12-bit SMPTE 428-19 SMPTE 2048-2 4:4:4 YCbCr 12-bit/10-bit SMPTE 425-1 SMPTE 372 4:2:2 YCbCr 12-bit SMPTE 2048-2 4096x2160PsF 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 SMPTE 372 4:4:4 X'Y'Z' 12-bit SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2 4:4:4 YCbCr 12-bit/10-bit...
  • Page 88 Supported Signal Format Transmission method Signal format Color format Color depth Standards Quad Link 3G-SDI 4096x2160PsF 23.98/24.00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 425-1 (Level B) SMPTE 372 4:4:4 X'Y'Z' 12-bit SMPTE 428-9 SMPTE 428-19 SMPTE 2048-2 4:4:4 YCbCr 12-bit/10-bit SMPTE 425-1 SMPTE 372 4:2:2 YCbCr 12-bit SMPTE 2048-2 Quad Link 3G-SDI 3840x2160P 59.94/60.00 Hz 4:2:2 YCbCr 10-bit SMPTE 425-5 2 Sample Interleave SMPTE 372 3840x2160P 50.00 Hz 4:2:2 YCbCr 10-bit (Level B) SMPTE 274M...
  • Page 89 Supported Signal Format Transmission method Signal format Color format Color depth Standards Dual Link 6G-SDI 3840x2160P 59.94/60.00 Hz 4:2:2 YCbCr 10-bit SMPTE 2081-11 2 Sample Interleave 3840x2160P 50.00 Hz 12G-SDI 3840x2160P 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit SMPTE 2082-10 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 3840x2160P 25.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 3840x2160P 23.98/24.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr 4:2:2 YCbCr 12-bit 4096x2160P 25.00 Hz 4:4:4 RGB 12-bit/10-bit 4:4:4 YCbCr...
  • Page 90 Supported Signal Format HDMI Signal format Color format/Color depth 640x480P 59.94/60.00 Hz 4:4:4 RGB 8-bit 800x600P 60.00 Hz 1024x768P 60.00 Hz 720x480P 59.94/60.00 Hz 4:4:4 RGB 12-bit/10-bit/8-bit 4:4:4 YCbCr 12-bit/10-bit/8-bit 720x576P 50.00 Hz 4:2:2 YCbCr 12-bit 1280x720P 59.94/60.00 Hz 1280x720P 50.00 Hz 1920x1080P 59.94/60.00 Hz 1920x1080i 59.94/60.00 Hz 1920x1080P 50.00 Hz 1920x1080i 50.00 Hz 1920x1080P 29.97/30.00 Hz 1920x1080P 25.00 Hz 1920x1080P 23.98/24.00 Hz 2048x1080P 59.94/60.00 Hz 2048x1080P 50.00 Hz 2048x1080P 29.97/30.00 Hz 2048x1080P 25.00 Hz 2048x1080P 23.98/24.00 Hz 3840x2160P 59.94/60.00 Hz 4:4:4 RGB 8-bit 4:4:4 YCbCr 8-bit 3840x2160P 50.00 Hz 4:2:2 YCbCr 12-bit 4:2:0 YCbCr 12-bit/10-bit/8-bit 3840x2160P 29.97/30.00 Hz 4:4:4 RGB 12-bit/10-bit/8-bit 4:4:4 YCbCr 12-bit/10-bit/8-bit 3840x2160P 25.00 Hz 4:2:2 YCbCr 12-bit...

  • Page 91: Image/Frame Display

    Image/Frame Display Signal system Display Method 720×487 59.94 59.94 720×576 50.00 50.00 1280x720 23.98/24.00 47.96/48.00 25.00 50.00 29.97/30.00 59.94/60.00 50.00 50.00 59.94/60.00 59.94/60.00 1920x1080 50.00 50.00 59.94/60.00 59.94/60.00 23.98/24.00 47.96/48.00 25.00 50.00 29.97/30.00 59.94/60.00 23.98/24.00 47.96/48.00 25.00 50.00 29.97/30.00 59.94/60.00 50.00 50.00 59.94/60.00 59.94/60.00...
  • Page 92 Image/Frame Display Signal system Display Method 3840x2160 50.00 50.00 59.94/60.00 59.94/60.00 23.98/24.00 47.96/48.00 25.00 50.00 29.97/30.00 59.94/60.00 23.98/24.00 47.96/48.00 25.00 50.00 29.97/30.00 59.94/60.00 50.00 50.00 59.94/60.00 59.94/60.00 4096x2160 23.98/24.00 47.96/48.00 25.00 50.00 29.97/30.00 59.94/60.00 23.98/24.00 47.96/48.00 25.00 50.00 29.97/30.00 59.94/60.00 47.95/48.00 47.95/48.00 50.00...
  • Page 93 Image/Frame Display HDMI Signal system Display Method 640x480 59.94/60.00 59.94/60.00 800x600 60.00 60.00 720x480 59.94/60.00 59.94/60.00 720x576 50.00 50.00 1024x768 60.00 60.00 1280x720 59.94/60.00 59.94/60.00 1280x720 50.00 50.00 1920x1080 59.94/60.00 59.94/60.00 1920x1080 59.94/60.00 59.94/60.00 1920x1080 50.00 50.00 1920x1080 50.00 50.00 1920x1080 29.97/30.00 59.94/60.00...

  • Page 94: Error Messages

    Error Messages Message Description and Action Network Communication error. IP address may be in conflict or there may be a network communication error. Check the network environment. Invalid IP Address. Enter the correct IP address. Invalid Subnet Mask. Enter the correct subnet mask. Various settings, The USB memory is full. Use another USB memory or delete the content of CDL export the memory. Failed to write file. The USB memory may be defective or protected. Check the USB memory. LUT, Various settings, (LUT Import) "LUT Type" is different. Select the correct file format. CDL import (CDL Import) "File Type" is different. Failed to read file. The USB memory may be defective or protected. Check the USB memory. Failed to import. There is an error in the file to be imported. Check the file. No import file. Check and ensure that the file has been saved to the USB memory or imported to [User 1] to [User 3]. Screen Capture Failed to capture. The USB memory may be defective or protected. Check the USB memory. Invalid Signal.
  • Page 95 Error Messages Message Description and Action Hardware error Backlight error. Disconnect the power cord, reconnect it, and then turn on the power. Fan error. If the message persists, contact Canon Customer Panel error. Center. I/F error. Audio I/F error. System error. Input signal No Signal Displayed when there is no video signal input. Unsupported Unsupported video signal is input. Check the supported signal format ( 77). Operation Invalid operation. Operation is disabled. Check the setting items. "Protect Settings" is on. To use the OSD menu, move the selection frame to [Protect] and press the jog dial for approximately 3 seconds. "CDL/User LUT Bypass" is on. When [CDL/User LUT] [Bypass] is turned [On], you cannot adjust [Power], [Saturation], [Offset], or [Slope]. Invalid Password. Enter the correct password. No license. This function cannot be used as the license file has not been applied. Refer to the Canon website for...
  • Page 96 Error Messages Message Description and Action Low Voltage. The battery charge level drops if using the battery. DC power supply If you use another power source, check the input voltage of the DC power supply. Low Voltage, Turn off power. The power has shut off as DC power voltage became insufficient for continued operation. There may not be enough energy left if you are using the battery. Connect a charged battery and turn the video display power on. If you use another power source, check the input voltage of the DC power supply. Invalid Voltage, Turn off power. The power has shut off as the DC power input voltage exceeded the operational threshold. Check the input voltage of the DC power supply. Power Saving No Signal, Turn off power by Power Save function. This indicates that there have not been any signals for the time set to [Power Save]. The power will be turned off approximately 5 minutes later. Check the input signal. No Signal, Turn off power. This indicates that the power is turned off after approximately 5 minutes as there has been no signal. Check the input signal.

  • Page 97: Troubleshooting

    (Power indicator does not turn on.) • Check that the power cord is connected correctly. • Brightness of the power indicator may be turned off. Turn it on and check once more. The screen is dark. When the power indicator does not turn on: — • Press the button. • Check that the power cord is connected correctly. When the power indicator is lit orange: — • Press the button. When the power indicator is flashing orange: — • Flashing once every 3 seconds : Contact Canon Customer Center. • Flashing twice every 3 seconds : - Turn on the power with the button. - The temperature of the display rises (or falls) depend on operation environment. Check the environmental conditions and do not use in direct sunlight. - If the power still does not turn on, contact Canon Customer Center. The power was turned off when there When [Power Save] is set to an option other than [Off], the video display’s were not any signals. power is automatically turned off if the no video signal is input for a certain period of time. Turn on the power again. • Depending on the model of DC power supply used, the output voltage The power suddenly goes off when a DC may decrease suddenly and even turn off (0 V output) when a threshold power supply is used.
  • Page 98 Troubleshooting Symptom Cause and Action Burn-in image appears. • This is a characteristic of the LCD panel and you should avoid displaying stationary image for a long time. — • When burn-in image appears with the interlaced signal displayed, try changing setting to: [Channel Settings] [I/P Conversion] [Normal]. There is an unlit or red, blue, green, or • LCD display is made of very high precision technology. It has effective white dot on screen. pixels of 99.99% or more, but there may be black dots or red, blue, or — green dots that may be always on. This is not a failure. There is an interference pattern or trace • The symptom may be resolved by displaying a white or black image on that remains when the LCD panel is the entire screen. — pressed. OSD menu cannot be used. • Check that [Protect Settings] is not set. [Aspect Marker], [Safety Zone Marker] or • A channel with no signal, unsupported signal, or with [Input [Area Marker] does not appear. Configuration] not set may be selected. Check the signal. You forgot the password for [Protect • Press the jog dial and the button while the video display is in standby. —...

  • Page 99: Software Used In This Product

    Software Used in This Product Software installed with this product includes software modules from Canon or third parties. Software Developed by Canon and Free Software Software developed or created by Canon and accompanying document is protected by copyright law, terms of an international convention and any other governing laws. This product uses software modules under copyright by third parties and distributed as free software. Some of these software modules are subject to the GNU General Public License v2 and v3 (GPL), GNU Lesser General Public License v2.1 (LGPL) or any other license. Free software modules installed with this product • libupnp • libxml2 • libpng • lz4 • zlib • FreeRTOS • u-boot-xlnx • attr • avahi • base-files • base-passwd • bridge-utils • busybox • eudev • exfat-utils • fuse • fuse-exfat • gcc-runtime • glibc • init-ifupdown...
  • Page 100 Software Used in This Product THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL INTEL OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ■libxml2 License Copyright (C) 1998-2003 Daniel Veillard. All Rights Reserved. Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions: The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software. THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE DANIEL VEILLARD BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. Except as contained in this notice, the name of Daniel Veillard shall not be used in advertising or otherwise to promote the sale, use or other dealings in this Software without prior written authorization from him. ■lz4 LZ4 Library Copyright (c) 2011-2016, Yann Collet All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: * Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. * Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
  • Page 101 Software Used in This Product ■FreeRTOS Copyright (C) 2017 Amazon.com, Inc. or its affiliates. All Rights Reserved. Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions: The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software. If you wish to use our Amazon FreeRTOS name, please do so in a fair use way that does not cause confusion. THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. ■packagegroup-core-boot, shadow-securetty, udev-extraconf Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions: The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software. THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE ■shadow Copyright (c) The Regents of the University of California. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
  • Page 102 Software Used in This Product THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

  • Page 103: Index

    Firmware/License Update .......... 72 Firmware/License Ver. ..........76 Format ............... 38 Camera Information ........... 60 Frame Hold ............... 42 Camera Link .............. 60 Frame Luminance Monitor ......... 56 Canon Log, CanonLog 2, Canon Log 3 ..... 23 Function Button/Function Button (ALT) ...... 70 CDL Export/CDL Import ..........11 Function Button Guide ..........71 CDL/User LUT ............26 Function Settings ............52 Center Marker ............49...
  • Page 104 Gain R/G/B ..............22 MAC Address ............76 Gamma/EOTF ............23 Marker Preset ............45 GPI ..............16, 70 Marker Settings ............45 Green Off ..............66 MENU button .............. 4 Grid Marker ............... 49 Metadata ..............8 Monochrome ............. 66 Multi Information View ..........58 HDMI ..............90, 93 Multi View (Dual/Quad) ..........
  • Page 105 Range Check ............65 Vector Scope ............. 55 Red Off ..............66 Video Position (Multi View) ......... 42 Reduce Backlight Flash ........29 VITC ................52 Reset ................. 30 Volume ..............44 Reset All Settings ............73 RESET button .............. 4 Wave Form Monitor ........... 53 Web ..............18, 68 Safety Zone Marker ........... 46 Saturation ..............26 YCbCr Color Matrix ........... 28 Screen A ~ D .
  • Page 106 Canon Inc. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan Canon Europa N.V. Bovenkerkerweg 59, 1185 XB Amstelveen, The Netherlands http://www.canon-europe.com USA http://pro.usa.canon.com UNITED KINGDOM CANON U.S.A., INC. Canon UK Ltd http://pro.usa.canon.com/support Unit 160, Centennial Park, Centennial Avenue, (855) 4K-CANON (855-452-2666)

This manual is also suitable for:

Dp-v1830

Table of Contents