SONY SS-CS310CR - Speaker System Operating Instructions

Precautions

On safety

• Before operating the system, be sure that the operating voltage of the system is identical with that of your local power supply.
• Should any liquid or solid object fall into the system, unplug the system's power cord and have the system checked by qualified personnel before operating it any further.

On operation

• Do not drive the speaker system with a continuous wattage exceeding the maximum input power of the system.
• If the polarity of the speaker connections are not correct, the bass tones will be weak and the position of the various instruments obscure.
• Contact between bare speaker wires at the speaker terminals may result in a short-circuit.
• Before connecting, turn off the amplifier to avoid damaging the speaker system.
• (For center and surround speakers only) The speaker grille cannot be removed. Do not attempt to remove the grille on the speaker system. If you try to remove it, you may damage the speaker.
• The volume level should not be turned up to the point of distortion.

On placement

• Do not install the speakers in an inclined position.
• Do not place the speakers in locations that are:
  • Extremely hot or cold
  • Dusty or dirty
  • Very humid
  • Subject to vibrations
  • Subject to direct sunlight
  • Near magnetic cards (credit cards, commuter passes, etc.)
    Magnetic cards may fail due to the magnets in the speaker units.
  • Near televisions
    The speakers are not magnetically shielded. Therefore, if you use the speakers near CRT-based televisions, color shading occurs on the television screen.
• Use caution when placing the speaker on a specially treated (waxed, oiled, polished, etc.) surfaces, as staining or discoloration may result.

On cleaning

Clean the speaker cabinets with a soft cloth lightly moistened with a mild detergent solution or water. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine.

If you have any questions or problems concerning your speaker system, please consult your nearest Sony dealer.

Positioning the speakers (A)

Each speaker should face the listening position. Better surround effect will result if all speakers are set at the same distance from the listening position.

Place the speakers as follows:

Front speakers: suitable distance to the left and right of the television.

Subwoofer (not supplied): on either side of the television.

Center speaker: in front of the television.

Surround speakers: depends on the configuration of the room. The surround speakers may be placed slightly behind the listening position.

Note
Be sure to place the speaker in a flat, horizontal place.

Assembly

Attaching the foot pads (B)

Be sure to attach the supplied foot pads to the bottom of the speakers to stabilize the speakers and prevent them from slipping.

Installing the surround speakers on the wall (C)

You can hang the surround speaker with a hook (not supplied) on the wall.

Before install the speakers on the wall, connect the speaker cord to the speaker.

1. Prepare screws (not supplied) that are suitable for the hole on the back of the speakers.
2. Fasten the screws to the wall. The screws should protrude 7 mm to 10 mm.
3. Hang the speakers on the screws.

Notes

• Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach the screws securely to a beam and fasten them to the wall. Install the speakers on a vertical and flat wall where reinforcement is applied.
• Contact a screw shop or installer regarding the wall material or screws to be used.
• Sony is not responsible for accident or damage caused by improper installation, insufficient wall strength or improper screw installation, natural calamity, etc.

Hooking up the system (D)

Be sure to turn off the power of the amplifier and the subwoofer (not supplied) before making any connection.

Connect the front, center and the surround speakers to the speaker output terminals of an amplifier and use the LINE IN jack of the subwoofer (not supplied) to connect to the amplifier.

Be sure to use the long speaker cord to connect the surround speakers and the short speaker cord to connect the front and center speakers.

Notes (E)

• Make sure the plus (+) and the minus (–) terminals on the speakers are matched to the corresponding plus (+) and minus (–) terminals on the amplifier.
• Make sure all connections are firm. Contact between bare speaker wires at the speaker terminals may cause a short-circuit.
• For details on the amplifier connections, refer to the operating instructions supplied with the amplifier.

Tip

Black or black striped wires are minus (–) in polarity, and should be connected to the minus (–) speaker terminals.

Setting the amplifier

When connecting to an amplifier with internal multi channel decoders (Dolby Digital^a), DTS^b), etc.), you should use the setup menus for the amplifier to specify the parameters of your speaker system.

The setup menus for the amplifier differ depending on whether or not a subwoofer (not supplied) is used. See the table below for the proper settings. For details on the setting procedure, refer to the operating instructions supplied with your amplifier.

Speaker setup (Subwoofer is used)

Speaker setup (Subwoofer is not used)

^a) "Dolby" and the double-D symbol are trademarks of Dolby Laboratories.

^b) "DTS" and "DTS Digital Surround" are registered trademarks of DTS, Inc.

^c) If you use a subwoofer, we recommend you set the front speakers to "LARGE". However, if distortion occurs, set the front speakers to "SMALL".

Troubleshooting

Should you encounter a problem with your speaker system, check the following list and take the indicated measures. If the problem persists, consult your nearest Sony dealer.

There is no sound from the speaker system.

• Make sure all the connections have been correctly made.
• Make sure the volume on the amplifier has been turned up properly.
• Make sure the program source selector on the amplifier is set to the proper source.
• Make sure the headphones are not connected.

There is hum or noise in the speaker output.

• Make sure all the connections have been correctly made.
• Make sure none of the audio components are positioned too close to the TV set.

The sound has suddenly stopped.

• Make sure all the connections have been correctly made. Contact between bare speaker wires at the speaker terminals may cause a short-circuit.

Specifications

SS-CS3 (Front speakers)

Speaker system: 3-way 4-driver speaker system, Bass reflex

Speaker units:
Woofer: 130 mm, cone type (2)
Tweeter: 25 mm, soft dome type (1)
Super tweeter: 19 mm, soft dome type (1)

Rated impedance: 6 ohms

Power handling capacity: Maximum input power: 145 W

Sensitivity level: 88 dB (2.83 V, 1 m)

Frequency range: 45 Hz - 50,000 Hz

Dimensions (width/height/depth): Approx. 230 × 922 × 260 mm including front grille

Mass: Approx. 11.5 kg including front grille

SS-CS10C (Center speaker)

Speaker system: Full range, Bass reflex

Speaker units: 70 mm, cone type (2)

Rated impedance: 6 ohms

Power handling capacity: Maximum input power: 145 W

Sensitivity level: 82 dB (2.83 V, 1 m)

Frequency range: 150 Hz - 20,000 Hz

Dimensions (width/height/depth): Approx. 411 × 87 × 93 mm including front grille

Mass: Approx. 1.7 kg including front grille

SS-CS10S (Surround speakers)

Speaker system: Full range, Bass reflex

Speaker units: 70 mm, cone type (1)

Rated impedance: 6 ohms

Power handling capacity: Maximum input power: 145 W

Sensitivity level: 80 dB (2.83 V, 1 m)

Frequency range: 150 Hz - 20,000 Hz

Dimensions (width/height/depth): Approx. 96 × 171 × 113 mm including front grille

Mass: Approx. 0.9 kg including front grille

Supplied accessories

Speaker cord (short) (3)

Speaker cord (long) (2)

Foot pads (large) (8): for front speakers (SS-CS3)

Foot pads (small) (12): for center (SS-CS10C) and surround (SS-CS10S) speakers

Design and specifications are subject to change without notice.

Disposal of Old Electrical & Electronic Equipment

(Applicable in the European Union and other European countries with separate collection systems)

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.

Notice for customers: The following information is only applicable to equipment sold in countries applying EU Directives.

This product has been manufactured by or on behalf of Sony Corporation, 1-7-1 Konan Minato-ku Tokyo, 108-0075 Japan. Inquiries related to product compliance based on European Union legislation shall be addressed to the authorized representative, Sony Belgium, bijkantoor van Sony Europe Limited, Da Vincilaan 7-D1, 1935 Zaventem, Belgium. For any service or guarantee matters, please refer to the addresses provided in the separate service or guarantee documents.

http://www.sony.net/

© 2014 Sony Corporation Printed in Malaysia