Table of Contents
Advertisement
SQUARING THE SAW BLADE TO THE FENCE
Remove the battery pack from the product.
Pull the saw arm all the way down and lock in transport position.
Lift the mitre lock lever to unlock the turning table.
Press the mitre detent release button and rotate the turning
table until the pointer on the mitre scale is positioned at 0°.
Release the mitre detent release button and allow the turning
table to engage the 0° detent position.
Push the mitre lock lever down to lock the turning table.
Loosen the bevel lock knob and set the product at the 0° bevel
angle.
Securely tighten the bevel lock knob.
NOTE:
saw blade, not the blade teeth.
See figure 8.
If the front or back edge of the saw blade angles away from the
Lift the mitre lock lever to unlock the turning table.
Press the mitre detent release button and rotate the turning
table until the pointer is at the left 30° position on the mitre scale
detent plate. See figure 8.
Loosen the 3 screws that hold the mitre scale detent plate in
place.
Press the mitre detent release button and rotate the turning
table to the 0° position on the mitre scale or until the detent
engages in the detent plate.
Adjust the mitre angle until the blade is parallel with the framing
If adjustments are needed, refer to To adjust the mitre
angle in the Adjustments section.
Push the mitre lock lever down to lock the turning table.
Tighten the 2 visible screws that secure the mitre scale detent
plate.
Lift the mitre lock lever to unlock the turning table.
Press the mitre detent release button and rotate the turning
table to the left 30° position on the mitre scale. See figure 8.
Tighten the remaining screw to secure the mitre scale detent
plate.
SQUARING THE BLADE TO THE TURNING TABLE
To square the blade at 0°:
Remove the battery pack from the product.
Pull the saw arm all the way down and engage the head lock pin
to hold the saw arm in transport position.
Lift the mitre lock lever, then depress and hold the mitre detent
release button to release the turning table.
Rotate the turning table until the scale indicator is positioned
at 0°.
Release the mitre detent release button and allow the turning
table to engage the 0° detent position. Push the mitre lock lever
down to secure the turning table.
Push the single/ dual bevel selector inward. See figure 4.
Loosen bevel lock knob and tilt saw arm until it is seated in the
positive 0° bevel stop (blade set 90° to turning table). Tighten
bevel lock knob.
flat part of saw blade.
18
NOTE:
saw blade, not the blade teeth.
Rotate the blade by hand and check the blade-to-table
alignment at several points.
shown in figure 13.
If the top or bottom of the saw blade angles away from the
Loosen the bevel lock knob.
Adjust 0° bevel stop screw to bring saw blade into alignment
section.
Retighten bevel lock knob. Recheck blade-to-table alignment.
To square the blade at 45°:
Loosen the bevel lock knob and set the saw arm at 45° bevel.
Tighten bevel lock knob.
NOTE: To obtain right bevel angles, pull the single/ dual bevel
selector out and tilt the saw to the desired angle.
as described earlier.
If adjustments are needed, refer to 45° Bevel Adjustment in the
Adjustments section.
adjustments have been made, it may be necessary to loosen
the indicator screws and reset them to zero. See figures 6-7.
OPERATION
Do not allow familiarity with products to make you careless.
Always wear eye protection with side shields. Failure to do so
could result in objects being thrown into your eyes, resulting in
possible serious injury.
Do not use any attachments or accessories not recommended
by the manufacturer of the product. The use of attachments or
accessories not recommended can result in serious personal
injury.
To avoid serious personal injury, always push the mitre lock lever
down and tighten the bevel lock knob securely before making a
cut. Failure to do so could result in movement of the control arm
or turning table while making a cut.
Do not start the product without checking for interference
between the blade and the mitre fence. Damage could result
to the blade if it strikes the mitre fence during operation of the
product. Failure to heed this warning can also result in serious
personal injury.
18
WARNING
WARNING
WARNING
WARNING
WARNING
Advertisement
Table of Contents
