Table of Contents
Advertisement
Always wear goggles and ear protection when using the machine. It
is recommended to wear gloves, sturdy non-slip shoes and apron.
Before using any accessory, consult the instruction manual. The
improper use of an accessory can cause damage and increase the
potential for injury.
Observe the maximum speed marked on the saw blade. Ensure
marked on the saw.
Always use blades with correct size and shape of arbour holes.
Blades that do not match the mounting hardware of the saw will run
eccentrically, causing loss of control.
Do not use blades of larger or smaller diameter other than
the spindle.
Check the tips of the saw blade for damage or abnormal appearance
objects in use and increase the chance of personal injury.
Do not use cracked or distorted saw blades. Do not use saw blades
that are damaged or deformed.
Scrap the saw blade if damaged, deformed, distorted or cracked,
repairing is not permitted.
Do not use HSS blades.
Ensure the saw blade is mounted correctly, tighten the arbor nut
Fastening screw and nuts shall be tightened using the appropriate
spanner, etc.
Extension of the spanner or tightening using hammer blows is not
permitted.
of the collar are against the blade.
Make sure the blade rotates in the correct direction.
Before work, make a dummy cut without the motor turned on so the
position of the blade, operation of the guards with respect to other
machine parts and workpiece may be checked.
Never leave the machine unattended.
Do not apply lubricants on the blade when it is running.
Never perform any cleaning or maintenance work when the machine
is still running and the head is not in the rest position.
Never attempt to stop a machine in motion rapidly by jamming a tool
or other means against the blade, serious accidents can be caused
unintentionally in this way.
Disconnect the saw from the mains supply or remove battery pack
before changing blades or carrying out maintenance.
Pay attention to blade packing and unpacking, it is easy to be
injured by the sharp blade tips.
Use a blade holder or wear gloves when handling a saw blade.
Keep and store the blade in original packaging or other suitable
packaging, keep in dry conditions and away from chemicals which
may damage the blade.
SPECIFIED CONDITIONS OF USE
The dual bevel slider mitre saw is intended for sawing solid and
bonded wood with or without glued veneer, plastics, and materials
similar to wood.
The dual bevel slider mitre saw is intended to be used only by adult
operators who have read the instruction manual and understand the
risks and hazards.
machine may move during cutting operations, which increases the
possibility of serious personal injury.
The dual bevel slider mitre saw is designed make bevel and mitre
cuts. The capacities for the various cuts are provided in the product
16
The dual bevel slider mitre saw is to be used in dry conditions, with
The dual bevel slider mitre saw is intended for consumer use and
should only be used as described above and is not intended for any
other purpose.
RESIDUAL RISKS
Even when the dual bevel slider mitre saw is used as prescribed,
it is still impossible to completely eliminate certain residual risk
factors. The following hazards may arise and the operator should
pay special attention to avoid the following:
Risk of contact with uncovered parts of the rotating saw blade.
Kick-back of work pieces or parts of work pieces due to improper
adjustment or handling.
Catapulting of faulty carbide tips from the saw blade. Wear Eye
protection at all times.
Damage to the respiratory system. Wear respiratory protection
masks containing filters appropriate to the materials being
drink or smoke in the work area.
Damage to hearing if effective hearing protection is not worn.
Dust from certain paints, coatings, and materials may cause
irritation or allergic reactions. Dust from wood such as oak,
beech, MDF, and others are carcinogenic. Materials containing
specialist operators.
Injuries may be caused or aggravated by prolonged use of a
tool. When using any tool for prolonged periods, ensure you take
regular breaks.
ASSEMBLY
UNPACKING
Packing list
Dust bag x 1
Work clamp x 1
Sliding fence x 1
Carrying handle x 1
Nylon nut x 2
Hex socket bolt x 2
Operation manual x 1
Carefully lift saw from the carton by the carrying handle and the saw
base, and place it on a level work surface.
The product has been shipped with the saw arm secured in the
down position. To release the saw arm, push down on the top of the
saw arm, cut the tie-wrap, and pull out the head lock pin.
The saw arm is spring loaded. Hold the handle down to prevent
saw arm from snapping up when cutting the tie-wrap. Failure to
do so could result in possible serious injury.
Lift the saw arm by the handle. Hand pressure should remain on
16
WARNING
WARNING
WARNING
Advertisement
Table of Contents
