Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HIKVISION C30 Series
Summary of Contents for HIKVISION C30 Series
- Page 1 C30 Series Video Wall Controller User Manual...
- Page 2 The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version of this Manual at the Hikvision website (https://www.hikvision.com/).
- Page 3 Video Wall Controller • User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
- Page 4 Video Wall Controller • User Manual Preface Applicable Models This manual is applicable to C30 series video wall controllers. About the Default This device has the following defaults. Category Parameter Default Value User name: admin Device Login username and IP address IP Address: 192.0.0.64...
- Page 5 Video Wall Controller • User Manual Safety Instructions In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. During the operations such as wring and dismounting, make sure to disconnect the power supply of the device.
-
Page 6: Table Of Contents
Video Wall Controller • User Manual TABLE OF CONTENTS Chapter 1 Introduction ....................... 1 Overview ................................1 Operation Instructions ............................1 1.2.1 Introduction of Smart Wall Configuration Client ..................1 1.2.2 Introduction of Smart Wall Control Client ....................1 Chapter 2 Device Activation ....................... 2 Activate Device via SADP Software ........................ -
Page 7: Chapter 1 Introduction
Video Wall Controller • User Manual Chapter 1 Introduction Overview The DS-C30S series video wall controller is a new-generation pure hardware image processing device based on Field Programmable Gate Array (FPGA). Compared with the traditional controller, the device has a brand-new system architecture and adopts data dual exchange technology to support large-capacity data transmission and processing. -
Page 8: Chapter 2 Device Activation
Video Wall Controller • User Manual Chapter 2 Device Activation Please activate your device when using it for the first time. Activate Device via SADP Software Open SADP. Activate Device Select the device that is not activated. Enter the password and confirm it on the right corner. Click Activate. - Page 9 Video Wall Controller • User Manual The factory IP address of the device is 192.0.0.64. The computer IP address can be set to anywhere between 192.0.0.2 to 192.0.0.253 such as 192.0.0.100. Enter 192.0.0.64 in the browser to view the activation interface. Set the device activation password.
-
Page 10: Chapter 3 Web Configuration
Video Wall Controller • User Manual Chapter 3 Web Configuration Log in to the Web After the device is activated, enter the IP address of the device in the browser. Enter the account number and the password to log in to the Web of the device. The account number is admin and the password is the activation password. - Page 11 Video Wall Controller • User Manual 2. According to the cabinet number on site, click the frame on the right to connect the sending card with the cabinet screen. 3. Click OK. The following figure shows an example: The sending port numbered 1 is connected to the cabinet screen numbered 1-1 and 1-2 from left to right.
- Page 12 Video Wall Controller • User Manual View the Receiving Card Status Enter Video Wall Configuration → Decoding Output. Select LED sending card in the Output List (Example of naming the LED sending card: LEDSendCard_Board19_1). Right-click and select Signal Cable Configuration. 1.
- Page 13 Video Wall Controller • User Manual Reset All Sending Ports: Reset the connection settings of all sending ports. 6. Click OK. Set On-Site Connection After the setting, the cabinet screen on site will display black. Set Basic Parameters Set basic parameters of the receiving card display. Enter Video Wall Configuration →...
- Page 14 Video Wall Controller • User Manual Basic Control Set basic parameters. Eye Protection: Turn on to filter blue light. Please operate according to the requirement. Brightness Adjustment: When turned on, the screen will automatically adjust the screen brightness according to the ambient brightness. Please operate according to the requirement. Set Image Adjustment.
- Page 15 Video Wall Controller • User Manual Manual Correction Select the correction range. Click to correct the entire cabinet screen. Select the screen as required. Click to correct part of the cabinet screen. Set the start and end coordinates as required.
- Page 16 Video Wall Controller • User Manual − Click Horizontal Line, correct all the horizontal seams. − Click Vertical Line, correct all the vertical seams. 3. Adjust the process bar of Seam Width. 4. Adjust the red, green, and blue progress bars and the RGB value. When the value of the on-site screen is greater than the parameter value of the progress bar, the correction will be carried out.
-
Page 17: Configure Virtual Led
Video Wall Controller • User Manual Click Browse, select the correction file to Upload. (Optional) If you need to back up the correction file, click Export, and select the download path to export the correction file. Configure the Receiving Card It is used to configure the display parameters of the receiving card. - Page 18 Video Wall Controller • User Manual Virtual LED Select a virtual LED. Click to set the following parameters.
- Page 19 Video Wall Controller • User Manual Modify Virtua LED The Meanings of Virtual LED Parameters Parameter Item Parameter Name Meaning Text Settings The text of the virtual LED frame. Time Settings The time displayed in the virtual LED frame. Text and Background Display Mode The transparency degree of the Settings...
-
Page 20: Configure Signal Source
Video Wall Controller • User Manual Parameter Item Parameter Name Meaning Background Color The default color is red. It is adjustable. Font Direction Horizontal or vertical. Multiple virtual LED frames can only apply the same font direction, which cannot be mixed. Alignment Align Left, Center, or Right. -
Page 21: Image Fine Tuning
Video Wall Controller • User Manual It is used to fine tune the image pixels and crop the signal source. Enter Configuration → Signal Source Configuration → Image Fine Tuning. Image Fine Tuning Select a signal source. Set the unit of fine tuning. Up to 10 pixels are supported in each direction. Click the direction keys to adjust the direction of the image. -
Page 22: Signal Source Splicing
Video Wall Controller • User Manual Select a signal source. Set the cropping pixels of four edges. The pixel range of cropping in all directions is between 0 and 200. It is required to be a multiple of 2, and 4 × 2 alignment. Click Save. -
Page 23: Custom Resolution
Video Wall Controller • User Manual Add Signal Source Splicing Customize the name and scale of the signal source. Drag the channel in the signal source list on the left to the splicing grid on the right. Click OK. (Optional) Select a spliced signal source to perform the following operations. ... -
Page 24: Osd
Video Wall Controller • User Manual Custom Resolution Enable Custom Resolution. Select a signal source. Set the refresh rate and resolution. The resolution supports down to 1280 × 720 and up to 4092 × 2160. And the width must be a multiple of 4, the height a multiple of 2. -
Page 25: Configure Display On Client
Video Wall Controller • User Manual Set OSD Select a signal source. Set the OSD ID. Up to 4 pieces of OSD information can be superimposed. Set the parameters such as OSD font size, font color, X coordinate and Y coordinate as required. Enable String, and enter the OSD information to be displayed. -
Page 26: Set Sub-Stream For Window Division
Video Wall Controller • User Manual Configure Display on Client Select a video wall. Set parameter values. Resolution: Select the resolution according to the requirement for video clarity. The higher the resolution, the higher the required network bandwidth. Frame rate: It refers to the number of frames per second of the video. The higher the frame rate, the smoother and more vivid the picture, which also means higher bandwidth and more storage space. -
Page 27: Configure The Network
Video Wall Controller • User Manual decoding. The sub-stream is suitable for low bandwidth networks, with smooth images and small bandwidth. Enter Configuration → Decoding Configuration → Sub-Stream for Window Division. Select Enable, set the Threshold Value of Sub-Stream Divisions, and click Save. Set the Sub-Stream for Window Division Example: When the threshold value of sub-stream divisions is set to 6, the sub-stream will be automatically selected for decoding when the number of screen divisions is greater than or equal... -
Page 28: Set Port
Video Wall Controller • User Manual Please do not modify the default port parameters randomly, otherwise the device will be unable to access. Enter Configuration → Network → Port. Set the port parameters and click Save to take effect. Set Port ... -
Page 29: Upgrade Led Receiving Card
Video Wall Controller • User Manual Illegal Login Exception: It means that the device will trigger the linkage action when the wrong user name or password is entered. Network Disconnection Exception: It means that the linkage action will be triggered if the device is not connected to the network cable or the network cable falls off. -
Page 30: Set Up Security Service
Video Wall Controller • User Manual Please do not turn off the power during the upgrade. The device will automatically restart after the upgrade. Set up Security Service Enter Configuration → Security Control → Security Service. Turn on or off the security service of the device according to the requirement. -
Page 31: Set Time
Video Wall Controller • User Manual The device name can be customized according to the requirement. Set the time zone, timing and daylight saving time of the device. Set Time Set Time Manually It is used to manually set the device time. Enter Configuration →... -
Page 32: Set Rs-485/Rs-232
Video Wall Controller • User Manual Click NTP. Fill in the Server Address and NTP port. The server address is the IP address or the domain name of the NTP server. Click Save. RS-485/RS-232 is used to access control signals. Use RS-485 cable to connect the device to the computer or the terminal.。... -
Page 33: Configure Font
Video Wall Controller • User Manual Configure Font Only Chinese TTF fonts are supported. The file size cannot exceed 15m, and the font file name cannot be repeated. It is used to view the open source software licenses of the device. Enter configuration →... - Page 34 Video Wall Controller • User Manual Default Enter Configuration → System → Maintenance → Upgrade & Maintenance. Click Default according to the requirement. All parameters of the device will be restored to the factory state. Please click with caution. Import/Export Configuration Parameters The configuration parameters of the device can be obtained by importing/exporting the configuration file of the device.
-
Page 35: Diagnosis
Video Wall Controller • User Manual Set Diagnosis Configure the syslog server. When the device generates logs, upload the logs to the syslog server. Please complete the deployment and configuration of the syslog server first.。 Enter Configuration → System → Maintenance → syslog. Set syslog Check Enable syslog. -
Page 36: User Management
Video Wall Controller • User Manual In order to improve the security of product network usage, please change your username and password regularly. It is recommended to update and maintain it every 3 months. If the device is used in a higher security risk environment, it is recommended to update it once a month or a week. -
Page 37: Log Management
Video Wall Controller • User Manual IP Filter Setting White User: It indicates that the IP addresses in the list are allowed to access the device. Black User: It indicates that none of the IP addresses in the list can access the device. Only admin users can add white user and black user. - Page 38 UD26426B...