Table of Contents
Advertisement
Quick Links
Contents
Get user manuals:
See SafeManuals.com
Q
S
G
UICK
TART
UIDE
Cabling the Cisco uBR10-MC5X20S/U/H Cable
Interface Line Card with Universal Cable
Holder—UCH2
Last Updated: May 14, 2009
OL-24878-01
This document contains the following information:
Feature Description
•
Installing the Cables
•
•
Installing the UCH
Removing the UCH
•
•
Removing the Cables
Troubleshooting
•
Related Documentation
•
Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Advertisement
Table of Contents
Related Manuals for Cisco uBR10-MC5X20S
Summary of Contents for Cisco uBR10-MC5X20S
- Page 1 Installing the Cables • • Installing the UCH Removing the UCH • • Removing the Cables Troubleshooting • Related Documentation • Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Get user manuals: See SafeManuals.com...
-
Page 2: Feature Description
Feature Description Feature Description The Cisco uBR10-MC5X20S, U and H cable interface line cards use 75–ohm precision video coax cables and 75–ohm MCX connectors to connect to the CMTS. This document describes how to install and remove cables and the second generation universal cable holder (UCH2). - Page 3 2 UCH2 Figure 3 shows the cable bundle for Cisco uBR10-MC5X20S/U/H cable interface line card to RF switch that has three UCH2 units attached to one end and two RF switch header blocks attached to the other end. This cable is 3.2 feet (1 m) long and the part number is CAB-RFSW520QTIMM2.
-
Page 4: Installing The Cables
Cisco preconfigured cable bundles. Installing the Cables The UCH must be used for all Cisco uBR10-MC5X20S/U/H line card cable connections. Failure to use the UCH may cause permanent damage to the line card connectors and result in low or no RF output. - Page 5 Precision miniature video coaxial cables come in various colors, and you can use any cable color Note combination. However, when you are connecting the Cisco uBR10-MC5X20S/U/H cable interface card to the Cisco RF switch, we recommend that you install the cables in the UCH as listed in Table Table 1...
- Page 6 Attach a jumper cable to the ground point on the chassis. Briefly touch each cable’s center connector with the jumper cable to remove any built-up ESD potential. Step 3 Cabling the Cisco uBR10-MC5X20S/U/H Cable Interface Line Card with Universal Cable Holder—UCH2 OL-24878-01 Get user manuals:...
- Page 7 If the UCH does not easily pull away from the card, loosen the lead screw until it completely disengages Note from the faceplate. Cabling the Cisco uBR10-MC5X20S/U/H Cable Interface Line Card with Universal Cable Holder—UCH2 OL-24878-01 Get user manuals: See SafeManuals.com...
-
Page 8: Removing The Cables
Be careful not to bend the cables. Caution Carefully pull the cable out of the hole. Step 3 Figure 8 Sliding Open the Lock Bar Cabling the Cisco uBR10-MC5X20S/U/H Cable Interface Line Card with Universal Cable Holder—UCH2 OL-24878-01 Get user manuals: See SafeManuals.com... -
Page 9: Troubleshooting
MCX connector strip tool: Dual-shielded cables PN–CPT-7538-125 Quad-shielded cables PN–CPT-7538-200Q Dual-shielded F connector strip tool CPT-7538 Quad-shielded F connector strip tool CPT-7538Q Cabling the Cisco uBR10-MC5X20S/U/H Cable Interface Line Card with Universal Cable Holder—UCH2 OL-24878-01 Get user manuals: See SafeManuals.com... -
Page 10: Related Documentation
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company.