Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Honeywell CM4680
Summary of Contents for Honeywell CM4680
- Page 1 CM4680 2D Imager Module Quick Start Guide CM4680-EN-QS Rev a 6/21...
-
Page 2: Additional Documentation
What is the CM4680 2D Imager Module The CM4680 is an encased compact 2D imager module for fixed mount applications. The CM4680 2D imager module includes the following features: • USB interface (micro USB connector) • Exit window • Beeper •... - Page 3 CM4680 2D Imager Module Views Mounting holes (x10) Status indicator Exit Mounting window holes (x10)
- Page 4 Mounting holes (x10) USB cable Beeper Slider to secure cable Mounting holes (x10)
-
Page 5: Connecting To A Host
Connecting to a Host By default, the scanner is in USB serial interface. Remove slider from module by pressing the ends and slid- ing it off. Connect a standard USB cable (standard USB-A to micro USB) to the module. USB cable... - Page 6 Secure the cable to the module using the slider: Place the cable through the center of the slider. Press the ends of the slider and slide it back on to the mod- ule until tight. Connect the USB cable to the host. Power-up the host.
-
Page 7: Configuration Bar Codes
Configuration Bar Codes Scan configuration bar codes to set up your scanner. All avail- able configuration bar codes are available in the N4680/ CF4680/CM4680 User Guide. Contact your local Honeywell OEM representative for more information. EZConfig for Scanning Tool Use the EZConfig for Scanning tool to configure your scanner Online: Go to the Honeywell https://hsmftp.honeywell.com. -
Page 8: Basic Setup
Basic Setup Here are some basic menu bar codes that may be useful for test- ing. For more setup options see the N4680/CF4680/CM4680 User Guide (available from your local Honeywell OEM represen- tative). Note: The * symbol indicates the default value. -
Page 9: Keyboard Country Layout
Keyboard Country Layout the default keyboard is United States. United States * French German Italian... -
Page 10: Beeper Volume
Beeper Volume Medium High *... -
Page 11: Presentation Mode
Presentation Mode The scanner LEDs remain dim and aimer off until a movement is detected, then the aimer turns on and LEDs light up to read the bar code. There are 2 types: Presentation Mode or Presentation Mode— Extended Reading Range. Presentation Mode: Optimized scan speed, limited reading range. -
Page 12: Reset Factory Defaults
Streaming Presentation The scanner LEDs are on all the time (continuous) and the aimer is off until a movement is detected, then the aimer turns on to read the bar code. There are 2 types: Normal or Enhanced. Streaming Presentation—Normal: Fast scan speed, limited reading range. -
Page 13: Mechanical Dimensions
Mechanical Dimensions USB cable 13.2 24.4 Units are in millimeters. Tolerances: ±0.5 mm. -
Page 14: Mounting Holes
Mounting Holes Use M3 screws with a maximum depth of 5.8 mm/0.23 in. Max torque 4.5kgf.cm/3.9 lbf.in and pull out resistance 736N. 12.5 30.5 13.5 42.5 Units are in millimeters. Tolerances ±0.5 mm. -
Page 15: Technical Specifications
Recommendations • Do not add an exit window over the existing exit window. • For best beeper performance, do not fully cover the beeper opening. • Be sure the cable is fitted tightly in the connector using the cable slider. The cable over mold should not be more than 23 mm/0.90 in. - Page 16 Environmental Storage Temperature -40°C to 85°C / -40°F to 185°F Humidity 5% to 95% RH, non-condensing Scanning Performance Sensor Global Shutter Resolution 640 x 480 Illumination White LED Illumination Aimer 625 nm visible red LED Motion Tolerance 6 m/s max Field of View Horizontal = 40°...
-
Page 17: Reading Distances
Reading Distances • Measured from the front center of the housing • 25°C, 200 lux for typical, 0 lux for guaranteed • Photographic barcodes • Serial Trigger mode Typical Symbology Near 13 mil UPC-A 4.3 cm / 1.7 in 38.5 cm / 15.2 in 10 mil Code 39 3.3 cm / 1.3 in 35.5 cm / 14 in... -
Page 18: Customer Support And Technical Assistance
If warranted goods are returned to Honeywell during the period of cover- age, Honeywell will repair or replace, at its option, without charge those items that Honeywell, in its sole discretion, finds defective. The forego- ing is buyer’s sole remedy and is in lieu of all other warranties,... - Page 19 The information we supply is believed to be accurate and reliable as of this writing. However, Honeywell assumes no responsibility for its use. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be pho- tocopied, reproduced, or translated into another language without the prior written consent of HII.