Download Print this page

Honeywell PEHA Easyclick 453 FU-RPP o.T Installation And Operating Instructions page 2

2-level repeater

Advertisement

Available languages

Available languages

PEHA Elektro GmbH & Co. KG
Postfach 1727 • D-58467 Lüdenscheid • Tel.: (02351)185-0 • Fax: (02351)27666 • e-mail: peha@peha.de • Internet: www.peha.de
Installation and Operating Instructions
Easyclick 2-level repeater
453 FU-RPP o.T.
1. General
1.1 Application
This repeater is used to increase the range between Easy-
click transmitters and receivers. In 1-level operation, a radio
signal received from a transmitter will be passed on to the
respective receiver. In 2-level operation a radio signal can
be passed over a maximum of two repeaters to a receiver!
Notes:
– The repeater is factory preset for 1-level operation
when delivered.
– Read through the operating instructions carefully
before putting the unit into service.
1.2 Guarantee conditions
These operating instructions are an integral part of both
the device and our terms of warranty. They must be furnis-
hed to the user. The technical design of the appliance is
subject to change without prior notification. PEHA products
are manufactured and quality-checked with the latest tech-
nology according to applicable national and international
regulations. Nevertheless, if a product should exhibit a de-
fect, PEHA warrants to make remedy as follows (regard-
less of any claims against the dealer to which the end-user
may be entitled as a result of the sales transaction):
In the event of a justified and properly-established claim,
PEHA shall exercise its prerogative to either repair or
replace the defective device. Further claims or liability
for consequential damages are explicitly excluded. A ju-
stifiable deficiency is one in which the device exhibits a
structural, manufacturing, or material defect that makes it
unusable or substantially impairs its utility at the time it is
turned over to the end-user.The warranty does not apply
to natural wear, unintended usage, incorrect connection,
device tampering or the effects of external influences. The
Vorsicht! Kontamination
warranty period is for 24 months from the date of purchase
Vorsicht! Kontamination
by the end-user from a dealer and ends not later than 36
months after the device's date of manufacture. German
law is applicable for the settlement of warranty claims.
1.3 Disposal of the device
Do not dispose of old devices in the household wa-
Vorsicht, Gefahr durch
Vorsicht, Gefahr durch
elektrischen Strom
elektrischen Strom
ste! The device must be disposed of in compliance
with the laws and standards of the country in which
it is operated! The device contains electrical compo-
nents that must be disposed of as electronics waste.
The enclosure is made from recyclable plastic
Vorsicht, Gefahr durch
Vorsicht, Gefahr durch
heiße Oberfläche
Laserstrahlung
2. Safety
CAUTION! Danger of electrical shock!
Current-carrying components are present
inside the housing. Contact can lead to
personal injury! All work on the mains net-
work and the device may only be done by an
Vorsicht, Warnung vor
Vorsichtig verschieben!
einer Gefahrstelle
- veraltet -
authorised electrician.
• Remove power from the device.
• Secure the device against being powered on again.
• Check that the device is powered off.
• Close the housing securely before applying power.
Wandhydrant (2.
Wandhydrant, mit Angabe
Vorschlag)
des Anschlusses
The following must be observed:
• Prevailing statutes, standards and regulations.
• State of the art technology at the time of installation.
• The device's operating instructions.
• Operating instructions can only cite general stipulations.
These are to be viewed in the context of a specific system.
Zust.
This device is only intended to be used for its stated appli-
cation. Unauthorised conversions or changes are forbidden!
This device may not be used in conjunction with other de-
vices whose operation could present a hazard to persons,
animals or property.
PEHA_M_453FU_RPP_oT (Rev03_130603)
3. Technical specifications
GB
Transmit frequency
Power supply
Power line protection
Ambient temperature
Storage temperature
Test specifications
Certifications
Protection type
4. Installation and commissioning
4.1 Safety notices
Assembly, installation and commissioning may only be done
by an authorised electrician. Mains power (230V / 50Hz ~)
to electrical equipment must be switched off during installa-
tion. Applicable laws and standards of the country in which
the device is operated must be observed!
4.2 Installation
This device is intended for installation in a flush-mount,
60 mm Ø installation box. It should be installed in an area
between the Easyclick sender and receiver. Radio signals
received from the sender can then be optimally passed on
to the receiver.
Note: NEVER install the repeater in a metal housing or in
the immediate vicinity of large metal objects. Installation
close to floor level or on the floor is not recommended.
Vorsicht, Gefahr durch
Vorsicht, Gefahr durch
Abquetschen
Abschneiden
Repeater
Vorsicht, Gefahr durch
Vorsicht, Gefahr durch
elektromagnetische
explosionsgefährliche
230V/50Hz~
Strahlung
Stoffe
Vorsicht, Gefahr durch
Vorsicht, Gefahr durch
Radioaktivität
Rutschen
• Install flush-mounted installation box in a suitable position.
Während der
Wandbrände nicht von
• Protect power supply cable with a circuit breaker
Schweißarbeiten,
oben löschen
Arbeitsstelle beobachten
or fuse (max. 10 A) !
• Install the connecting wires.
• Insert the device into the flush-mount installation box
and screw-fasten it securely in place.
• Affix the blind cover (Art. no.: xx.477.xx) to the device.
• Switch on electric power after installation.
D a t u m
Wareneingang -
Wareneingang - Gesperrt
• The repeater is factory preset for 1-level operation
Freigegeben
Bearb.
G e p r.
when delivered. Change the repeater to 2-level
N o r m
operation if this is desired (see Point 5.3).
Infratec
Datentechnik GmbH
Format DIN A4H
Ä n d e r u n g
Datum
Name
Urspr.:
126231-05
868,3 MHz
230V~ / 50 Hz
Circuit breaker or fuse
rated for 10 A, maximum
- 20° to + 40° C
- 40° to + 85° C
EN 60669-2-1
CE
IP 20
453 FU-RPP o.T.
Vorsicht, Gefahr durch
Button 1 LEV
Abstürzen
1 LEV
with LED 1
Activates 1-level
230V~
50Hz
operation
2 LEV
N N L L
Button 2 LEV
with LED 2
Activates 2-level
Vorsicht, Gefahr durch
operation
feuergefährliche Stoffe
N N L L
Receive radio signal:
LED 1 or 2 blinks red
F
N
L
Vorsicht, Gefahr durch
Accessories: blind cover (xx.477.xx)
Stolpern
Wandbrände von unten
nach oben löschen
N a m e
Wärmeabzugseinrichtung
Gehäusebedruckung
Dateiname:
5. Operating and functions
5.1 Operating
Manual operation of this device is not possible. The recei-
ving and sending of Easyclick radio signals is done auto-
matically.
5.2 1-level operation
In 1-level operation, a radio signal received from a trans-
mitter (LED 1 blinks red) will be passed on to the respec-
tive receiver.
453 FU-RPP o.T.
451 FU-BEP
1 LEV
1
230V~
µ
50Hz
Repeater
2 LEV
N N L L
L max.2500W
230V~/50Hz
230V~50Hz
N
Transmitter 1-level operation
Receiver
Activating 1-level operation:
453 FU-RPP o.T.
Press button 1 LEV a LED 1 lights up for about 3s
1 LEV
230V~
50Hz
longer than 2s
(1-level operation is active)
Repeater
2 LEV
Repeater
N N L L
453 FU-RPP o.T.
451 FU-BEP
5.3 2-level operation
1 LEV
1
230V~
In 2-level operation (LED 2 blinks red) a sender's radio
µ
50Hz
Repeater
D a t u m
N a m e
D a t u m
N a m e
2 LEV
Bearb.
Bearb.
N N L L
L max.2500W
signal will be received and passed on over a maximum of
G e p r.
G e p r.
N o r m
Gehäusebedruckung
N o r m
230V~/50Hz
230V~50Hz
N
two repeaters to the respective receiver.
Infratec
Infratec
Datentechnik GmbH
Datentechnik GmbH
Zust.
Ä n d e r u n g
Datum
Name
Urspr.:
Format DIN A4H
Zust.
Ä n d e r u n g
Dateiname:
Datum
Name
Urspr.:
Format DIN A4H
453 FU-RPP o.T.
1 LEV
230V~
50Hz
Repeater
Repeater
2 LEV
D a t u m
N a m e
D a t u m
N N L L
Bearb.
Bearb.
G e p r.
G e p r.
Gehäusebedruckung
N o r m
N o r m
Infratec
Infratec
Transmitter
2-level operation
2-level operation
Datentechnik GmbH
Datentechnik GmbH
Ä n d e r u n g
Datum
Format DIN A4H
Dateiname:
Format DIN A4H
Zust.
Name
Urspr.:
Zust.
Ä n d e r u n g
Datum
Name
Urspr.:
Zust.
Activating 2-level operation:
D a t u m
N a m e
D a t u m
N a m e
Bearb.
Bearb.
G e p r.
G e p r.
Press button 2 LEV a LED 2 lights up for about 3s
Gehäusebedruckung
N o r m
N o r m
longer than 2s
(2-level operation is active)
Infratec
Infratec
Datentechnik GmbH
Datentechnik GmbH
Zust.
Ä n d e r u n g
Datum
Urspr.:
Format DIN A4H
Zust.
Ä n d e r u n g
Dateiname:
Datum
Urspr.:
Format DIN A4H
Name
Name
6. Troubleshooting & remedies
D a t u m
N a m e
D a t u m
Bearb.
Bearb.
G e p r.
G e p r.
Gehäusebedruckung
N o r m
N o r m
Infratec
Infratec
6.1 New system or existing system
Datentechnik GmbH
Datentechnik GmbH
Ä n d e r u n g
Datum
Format DIN A4H
Dateiname:
Format DIN A4H
Zust.
Name
Urspr.:
Zust.
Ä n d e r u n g
Datum
Name
Urspr.:
Zust.
• Check circuit breaker and power supply
(electrician only).
• Check connection cables (electrician only).
• Check the system's surroundings for changes that could
cause interference (e.g. metal cabinets, furniture or walls
which have been moved).
• Use the repeater at a better location.
6.2 Radio signal range limitations
• Use of the repeater in the vicinity of metal objects or
materials with metal components. Maintain a distance
of at least 10 cm.
• Moist materials.
• Devices which emit high-frequency signals (e.g. audio
and video systems, computers, electronic ballasts in light
fixtures). Maintain a distance of at least 0.5 m.
6.3 Contact
Telephone:.............. +49 (0)2351 185-0
Fax: ........................ +49 (0)2351 27666
Internet:.................. www.peha.de
Email: ..................... peha@peha.de
7. Conformity declaration
PEHA Easyclick products may be sold and operated in
Blatt
1
EU countries as well as in CH, IS and N. PEHA herewith
1
Bl.
declares that this repeater (453 FU-RPP o.T.) is in compli-
ance with the fundamental requirements and other rele-
vant provisions of R&TTE-Guideline 1999/5/EG. The con-
formity declaration is available in Internet at the following
address: www.peha.de.
CLR/MODE
LRN/SET
L 1
453 FU-RPP o.T.
451 FU-BEP
1 LEV
CLR/MODE
1
230V~
µ
50Hz
2 LEV
LRN/SET
N N L L
L max.2500W
230V~/50Hz
230V~50Hz
N
L 1
CLR/MODE
LRN/SET
L 1
Blatt
Blatt
1
1
1
Bl.
1
Bl.
Dateiname:
453 FU-RPP o.T.
451 FU-BEP
1 LEV
CLR/MODE
1
230V~
µ
50Hz
2 LEV
LRN/SET
N a m e
D a t u m
N a m e
N N L L
L max.2500W
Bearb.
G e p r.
230V~/50Hz
230V~50Hz
Gehäusebedruckung
N o r m
N
L 1
Blatt
Blatt
Infratec
Receiver
1
1
1
Bl.
Datentechnik GmbH
1
Bl.
Format DIN A4H
Ä n d e r u n g
Dateiname:
Datum
Name
Urspr.:
Dateiname:
Blatt
Blatt
1
1
1
Bl.
1
Bl.
Dateiname:
N a m e
D a t u m
N a m e
Bearb.
G e p r.
Gehäusebedruckung
N o r m
Blatt
Blatt
Infratec
1
1
1
Bl.
1
Bl.
Datentechnik GmbH
Format DIN A4H
Ä n d e r u n g
Dateiname:
Datum
Name
Urspr.:
Dateiname:
GB - 1

Advertisement

loading