Summary of Contents for Siemens SIPROTEC Compact 7SC80
Page 1
Preface Contents DNP3 TCP Device Profile SIPROTEC Compact Feeder Protection Point Lists and Recloser Con- troller 7SC80 Flexible Mapping Index Communication Module DNP3 TCP Bus Mapping/Point Lists C53000-L2040-C353-3...
Page 2
, SINAUT , OSCOP , and DAKON registered trademarks of SIEMENS AG. An unauthorized use is Siemens AG reserves the right to revise this document from time to illegal. time. All other designations in this document can be trademarks whose Document Release: C53000-L2040-C353-3.01...
This manual is valid for SIPROTEC 4 Communication Module with DNP3 TCP. Further support Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser's purpose, the matter should be referred to the local Siemens representative. Hotline Our Customer Support Center provides around-the-clock support.
Page 4
Preface Notes On Safety This manual does not constitute a complete catalog of all safety measures required for operating the equipment (module, device) in question, because special operating conditions may require additional measures. However, it does contain notes that must be adhered to for your own personal safety and to avoid damage to property. These notes are highlighted with a warning triangle and different keywords indicating different degrees of dan- ger.
Page 5
The equipment (device, module) must not be used for any other purposes than those described in the Catalog and the Technical Description. If it is used together with third-party devices and components, these must be recommended or approved by Siemens. Correct and safe operation of the product requires adequate transportation, storage, installation, and mounting as well as appropriate use and maintenance.
Page 6
Preface SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists C53000-L2040-C353-3, Edition 09.2018...
1.1 Data Objects Implementation Note Further information see in the SIPROTEC 4 document Communication Module DNP3 TCP - Communication Profile, order number C53000-L2040-C354 or in Internet http://siemens.siprotec.de/download_neu/ index_e.htm. Data Objects Implementation The following table identifies which object variations, function codes and qualifiers the DNP3 TCP implemen- tation of the Feeder Protection and Recloser Controller 7SC80 will support in both request messages and in response messages.
Page 11
DNP3 TCP Device Profile 1.1 Data Objects Implementation Table 1-1 DNP3 TCP implementation table (Forts.) Objects Request Response Object Var. Description Function Codes Qualifier Codes Function Codes Qualifier Codes (dec) (hex) (dec) (hex) Binary Counter - (read) 00, 01 (start-stop) Any Variations 06 (no range, or all) 07, 08 (limited qfy)
Page 12
DNP3 TCP Device Profile 1.1 Data Objects Implementation Table 1-1 DNP3 TCP implementation table (Forts.) Objects Request Response Object Var. Description Function Codes Qualifier Codes Function Codes Qualifier Codes (dec) (hex) (dec) (hex) Class 2 Data (read) 06 (no range, or all) 07, 08 (limited qfy) Class 3 Data (read) 06 (no range, or all)
Page 14
DNP3 TCP Device Profile 1.2 DNP3 TCP Device Profile Documents DNP3 TCP DEVICE PROFILE DOCUMENT Timeouts while waiting for: Data Link Confirm None Fixed at 2 s Variable Configurable Complete Appl. Fragment None Fixed at _____ Variable Configurable Application Confirm None Fixed at _____ Variable...
Page 15
DNP3 TCP Device Profile 1.2 DNP3 TCP Device Profile Documents DNP3 TCP DEVICE PROFILE DOCUMENT Sends/Executes Control Operations: WRITE Binary Outputs Never Always Sometimes Configurable SELECT/OPERATE Never Always Sometimes Configurable DIRECT OPERATE Never Always Sometimes Configurable DIRECT OPERATE - NO ACK Never Always Sometimes...
Page 16
DNP3 TCP Device Profile 1.2 DNP3 TCP Device Profile Documents DNP3 TCP DEVICE PROFILE DOCUMENT Sends Unsolicited Responses: Sends Static Data in Unsolicited Responses: Never Never Configurable When Device Restarts Only certain objects When Status Flags Change Sometimes (attach explanation) No other options are permitted.
Page 17
DNP3 TCP Device Profile 1.2 DNP3 TCP Device Profile Documents DNP3 TCP DEVICE PROFILE DOCUMENT Sends Multi-Fragment Responses: Configurable DNP3 Source Address Validation Support Collision Avoidance Support multi-drop physical layers Sequential File Transfer Support: Append File Mode Custom Status Code Strings Permissions Field File Events Assigned to Class File Events Send Immediately...
Point Lists Binary Input Points Control Relay Output Blocks/Binary Output Status Counters Analog Inputs SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists C53000-L2040-C353-3, Edition 09.2018...
Point Lists 2.4 Analog Inputs Analog Inputs For scaling of measured values transmitted as 16-bit Analog Input please ref. to manual „DNP3 TCP communication profile“ Analog Inputs Static (Steady-State) Object Number: 30 Change Event Object Number: 32 Request Function Codes supported: 1 (read) Static Variation reported when variation 0 requested: 02 (16-bit Analog Input) Change Event Variation reported when variation 0 requested: 02 (Analog Change Event without Time) Point...
Page 27
Point Lists 2.4 Analog Inputs Analog Inputs Static (Steady-State) Object Number: 30 Change Event Object Number: 32 Request Function Codes supported: 1 (read) Static Variation reported when variation 0 requested: 02 (16-bit Analog Input) Change Event Variation reported when variation 0 requested: 02 (Analog Change Event without Time) Point Name Description...
Page 28
Point Lists 2.4 Analog Inputs SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists C53000-L2040-C353-3, Edition 09.2018...
Flexible Mapping Flexible Mapping SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists C53000-L2040-C353-3, Edition 09.2018...
Page 30
Flexible Mapping 3.1 Flexible Mapping Flexible Mapping The Flexible Mapping for DNP IP is a newly added function since 7SC80 V4.44. It can be selected by clicking the button Additional protocol at device. Figure 3-1 Selection of a Mapping File To create a mapping and select the used indications, click the button User-defined.
Index Analog Inputs 26 Recorded Measured Values 26 Binary Input Points 20, 30 Statistic Values 27 Binary Outputs / Commands 24 Voltage Protection 20 Changing the Setting Group 24 Control Mode REMOTE 24 Control Relay Output Blocks/Binary Output Status 24 Control Switches Return Position Indication 22 Counters 25 Data Objects Implementation 10...
Page 32
Index SIPROTEC Compact, Feeder Protection and Recloser Controller 7SC80, Bus Mapping/Point Lists C53000-L2040-C353-3, Edition 09.2018...