Page 1
U I C K ATA LY S T A N D I G H T A R D WA R E 100 Base Fx FAST ETHERNET MODULE 100 Base Fx FAST ETHERNET MODULE E F E R E N C E 85 10 1010 T R E A M...
Installing and Grounding the Chassis WARNING: Before you install, operate, or service the system, read the Site Preparation and Safety Guide. This guide contains important safety information you should know before working with the system. Installing the Rack WARNING: Three people are required to lift the chassis. To prevent damage to the chassis and components, never attempt to lift the chassis by the handles on the power supplies or on the interface modules, or by the plastic panels on the front of the chassis.
Ports and Cabling Slots 0-1: Port adapters/ 100 Base Fx Interface modules FAST ETHERNET MODULE Slot 2: Route processor Slots 3-4: Port adapters/ 100 Base Fx FAST ETHERNET MODULE Interface modules ROUTE PROCESSOR PORTS Ethernet port Console port Auxiliary port PORT ADAPTER/ INTERFACE MODULE PORTS...
Replacing Components Securing an ESD Strap WARNING: Always connect the ESD wrist strap to the ESD strap connection at the top left side of the chassis before removing any component. Replacing a Power Supply AC Power Supply DC Power Supply Captive On/off Captive...
Page 5
Top View of the Route Processor Edge connectors Replacing the Feature Card Press Here Press Here Screws Feature card Press Here Screws Press Here Route Processor Replacing a SIMM DRAM SIMM SIMMs socket Flash memory SIMM Spring clip Replacing an ACL Daughter Card Mounting Protective guard...
Page 6
Route Processor LEDs Enet Slot 1 accessed No signal System operating Slot 0 accessed Receiving signal System failed Transmitting signal System booting Installing and Removing Flash PC Cards Transmitting and Receiving : Flashing LED...
Page 7
Route Processor Port Pinouts Ethernet Port (RJ-45) Pinouts Pin Signal Direction Description —> Transmit data + TX– —> Transmit data – <— Receive data + RX– <— Receive data – Enet Auxiliary Port (DB-25) Pinouts Pin Signal Direction Description — Shield ground —>...
Page 8
Port Adapter Modules 4-port 25-Mbps 96-pin Molex connector Available Versions Product Number Product Description C85MS-ATM25-4P 4-port ATM25 Port Adapter Module 12-port 25-Mbps 96-pin Molex connector Available Versions Product Number Product Description C85MS-ATM25-12P 12-port ATM25 Port Adapter Module 155-Mbps Available Versions Product Number Product Description WAI-OC3-4U5...
Page 9
8-port T1 and E1 IMA Available Versions Product Number Product Description C85MS-8T1-IMA C8500MSR/LS1010 8-port T1 IMA Port Adapter Module C85MS-8E1-IMA-120 C8500MSR/LS1010 8-port E1 120-ohm IMA Port Adapter Module 4-port CES E1 and T1 Available Versions Product Number Product Description WAI-E1C-4BNC 4-port E1 (circuit emulation) with BNC interface Port Adapter Module Available Versions Product Number...
Pinout Information 96-Pin Molex to 12 Unshielded RJ-45 Connectors The 25-Mbps port adapter supports a 96-pin Molex to 4 unshielded RJ-45 connectors. The following table lists the signals for the 96-pin Molex connector. Signal Molex Pin No. RJ-45 Port No. RJ-45 Pin No.
Page 13
Signal Molex Pin No. RJ-45 Port No. RJ-45 Pin No. RXA9 RXB9 TXA9 TXB9 RXA8 RXB8 TXA8 TXB8 TXB5 TXA5 RXB5 RXA5 TXB0 TXA0 Description Signal Molex Pin No. No connection RXB0 No connection RXA0 Receive data + Receive data – No connection No connection MT-RJ Ethernet Cable Connectors...
Page 14
Specifications and Regulatory Compliance Information Description Specifications Switch and processor 10-Gbps shared memory, nonblocking switch fabric up to 32-KB capacity frames Dimensions (H x W x D) Chassis: 10.4 x 17.25 x 18.4 in (26.4 x 43.8 x 46.7 cm) Processor, switch processor, carrier module, and interface module: 1.2 x 14.4 x 16 in (3.0 x 36.6 x 40.6 cm) Port adapter: 1.2 x 6.5 x 10 in (3.0 x 16.5 x 25.4 cm)