Table of Contents
Advertisement
Available languages
Available languages
ENGLISH
Warning! Before you begin trimming, only use the appropriate
type of cutting line.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
Connect the brown lead to the live terminal in the new plug.
Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Troubleshooting
If your tool seems not to operate properly, follow the
instructions below. If this does not solve the problem, please
contact your local BLACK+DECKER repair agent.
Warning! Before proceeding, unplug the tool.
Machine runs slowly
Check that the spool housing can rotate freely. Carefully
clean it if necessary.
Check that the cutting line does not protrude more than
approximately 136mm from the spool. If it does, cut it off
so that it just reaches the line trimming blade.
Automatic line feed does not work
Remove the spool cap.
Pull the cutting line until it protrudes approximately 136mm
from the spool. If insufficient cutting line is left on the
spool, install a new spool of cutting line.
Ensure that the line is not crisscrossed on the spool as
detailed in Fig. S. If it is, unwind the cutting line, then wind
it back on the spool neatly so that the lines do not cross.
Ensure the beginning of the cutting line is pulled tight
against the spool as shown in Fig. S.
Align the tabs on the spool cap with the cut outs in the housing.
Push the spool cap onto the housing until it snaps
securely into place.
If the cutting line protrudes beyond the trimming blade,
cut it off so that it just reaches the blade. If the automatic
line feed still does not work or the spool is jammed, try the
following suggestions:
Carefully clean the spool and housing.
Remove the spool and check if the lever in the spool
housing can move freely.
Remove the spool and unwind the cutting line,
then wind it on neatly again. Replace the spool into
the housing.
Maintenance
Your BLACK+DECKER corded/cordless machine/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
10
(Original instructions)
depends upon proper tool/machine care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the machine/tool.
Or switch off and remove the battery from the machine/
tool if the machine/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
switch off.
Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your tool/machine
and charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Regularly clean the cutting line and spool using a soft
brush or dry cloth.
Regularly use a blunt scraper to remove grass and dirt
from the underneath of the guard.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical data
Voltage
V
AC
Power Input
W
No-Load Speed
min
-1
Weight
kg
Level of sound pressure:
Sound pressure (L
) 81 dB(A), uncertainty (K) 2.6 dB(A)
pA
Sound power (L
) 93 dB(A), uncertainty (K) 2.6 dB(A)
WA
Vibration total values (triax vector sum) according to EN 50636-2-91:
Vibration emission value (a
) 4.9 m/s
2
h
BESTA525
BESTA528
BESTA530
Type 1
Type 1
230
230
450
550
7500
7500
2.4
2.4
, uncertainty (K) 1.7 m/s
2
Type 1
230
550
7500
2.4
- Quick Links:
- English (Original Instructions)
Hide quick links:
Advertisement
Table of Contents
