Related Manuals for Makita BUC250C
Summary of Contents for Makita BUC250C
- Page 1 INSTRUCTION MANUAL Cordless Chain Saw BUC250 BUC250C 010915 IMPORTANT: Read Before Using.
-
Page 2: Specifications
ENGLISH (Original instructions) SPECIFICATIONS Model BUC250 BUC250C Chain speed per minute (min 8.3 m/s (500 m/min) Length of guide bar 250 mm Type 91VG 25AP Saw chain Pitch 3/8" 1/4" No. of drive links Number of teeth Overall length 576 mm... - Page 3 electric shock if your body is earthed or grounded. Power tool use and care Do not expose power tools to rain or wet 17. Do not force the power tool. Use the correct conditions. Water entering a power tool will power tool for your application.
- Page 4 Service When cutting a limb that is under tension be 28. Have your power tool serviced by a qualified alert for spring back. When the tension in the repair person using only identical replacement wood fibres is released the spring loaded limb may parts.
- Page 5 not let go of the chain saw. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight. Do not short the battery cartridge: Do not touch the terminals with any conductive material.
-
Page 6: Parts Description
PARTS DESCRIPTION Lever Saw chain Front hand guard Sprocket cover Top handle Chain cover Battery cartridge Lock off button Carabiner or rope Switch trigger attachment point Guide bar Front handle 010917... -
Page 7: Functional Description
Charge the battery cartridge before under any circumstances. Consult a MAKITA use. specialist repair shop. When the remaining battery capacity becomes low: Checking the run-down brake •... -
Page 8: Adjusting The Chain Lubrication
Always be sure that the tool is switched off and the • second when this test is performed, the saw must battery cartridge is removed before installing or not be used. Consult a MAKITA specialist repair removing the saw chain. shop. Always wear gloves when installing or removing the •... -
Page 9: Adjusting Saw Chain Tension
1. Adjusting pin 1. Press in 2. Loosen 010932 010935 Place the sprocket cover on the chain saw so that Press in the lever. With the lever depressed, make a the adjusting pin is positioned in a small hole in the quarter turn on it counterclockwise to loosen the nut guide bar. -
Page 10: Operation
The oil delivery may otherwise be impaired. As a saw chain oil, use oil exclusively for Makita • chain saws or oil available in market. Never use oil including dust and particles or volatile •... - Page 11 If you try to cut off thick branches from the top without a shallow undercut, the branch may splinter. 006915 Cut wood under tension on the pressure side (A )first. Then make the final cut on the tension side (B ). This 010922 If you cannot cut the timber right through with a single prevents the bar from becoming trapped.
- Page 12 1. Felling area 006923 006917 − Make the back cut a little higher than the base cut − Before starting felling work, ensure that: of the scarf. The back cut must be exactly Only persons involved in the felling operation horizontal.
-
Page 13: Maintenance
Two or three strokes with a file are usually sufficient for routine resharpening. When the saw chain has been resharpened several times, have it sharpened in a MAKITA specialist repair shop. File and file guiding − Use a special round file (optional accessory) for... -
Page 14: Replacing The Sprocket
Cleaning guide bar Replacing the sprocket Before fitting a new saw chain, check the condition of the sprocket. 1. Sprocket 2. Locking ring 010924 Chips and sawdust will build up in the guide bar groove, clogging it and impairing oil flow. Always clean out the 010927 chips and sawdust when sharpening or replacing the saw CAUTION:... - Page 15 Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. Various type of Makita genuine batteries and • chargers Saw chain •...
- Page 16 Makita Corporation 884950-5...