Related Manuals for Bosch NCD-274-PM
Summary of Contents for Bosch NCD-274-PM
- Page 1 MicroDome Camera 200 Series NDC-274-P, NDC-274-PT, NDC-284-PT, NCD-274-PM Installation Manual...
-
Page 3: Table Of Contents
DC power connection Mounting Camera set-up 3.7.1 Camera positioning Resetting the camera Closing the unit Browser connection Protected network Troubleshooting Resolving problems Customer service Maintenance Repairs 6.1.1 Transfer and disposal Bosch Security Systems Installation Manual AR18-10-B012 | v1.55 | 2012.09... - Page 4 | Table of Contents MicroDome Camera 200 Series Technical Data Specifications 7.1.1 Accessories AR18-10-B012 | v1.55 | 2012.09 Installation Manual Bosch Security Systems...
-
Page 5: Safety
If not avoided, this could result in minor or moderate bodily injury. CAUTION! Low risk: Indicates a potentially hazardous situation. If not avoided, this could result in property damage or risk of damage to the device. Bosch Security Systems Installation Manual AR18-10-B012 | v1.55 | 2012.09... -
Page 6: Important Safety Instructions
10. Attachments, changes or modifications - Only use attachments/accessories specified by the manufacturer. Any change or modification of the equipment, not expressly approved by Bosch, could void the warranty or, in the case of an authorization agreement, authority to operate the equipment. -
Page 7: Fcc & Ices Compliance
Any such modifications could void the user's authority to operate the equipment. If necessary, the user should consult the dealer or an experienced radio/television technician for corrective action. Bosch Security Systems Installation Manual AR18-10-B012 | v1.55 | 2012.09... -
Page 8: Ul Certification
Please dispose of these devices at an environmentally compatible recycling facility, per European Directive 2002/96/EC More information For more information please contact the nearest Bosch Security Systems location or visit www.boschsecurity.com AR18-10-B012 | v1.55 | 2012.09 Installation Manual... -
Page 9: Copyrights
Digital Equipment Corporation not be used in advertising or publicity pertaining to distribution of the software without specific, written prior permission. This software is based in part on the work of the Independent JPEG Group. Bosch Security Systems Installation Manual AR18-10-B012 | v1.55 | 2012.09... -
Page 10: Introduction
It uses H.264 compression technology to give clear images reducing bandwidth and storage.The camera can be used as a stand-alone video surveillance system with no additional equipment or it can easily integrate with the Bosch DVR 700 Series recorders. Features include: –... -
Page 11: Unpacking
Quick installation guide – Torx screwdriver for dome cover – Optical disk – Bosch Video Client – Documentation – Tools If equipment has been damaged during shipment, repack it in the original packaging and notify the shipping agent or supplier. -
Page 12: Installation
To disassemble the unit proceed as follows: Using the special screwdriver bit supplied, loosen the three tamper-resistant screws in the dome (the screws remain in place). Remove the dome from the base. AR18-10-B012 | v1.55 | 2012.09 Installation Manual Bosch Security Systems... -
Page 13: Memory Card
Desiccant for rugged cameras Figure 3.2 Desiccant for PT and PM camera versions. Remove backing from desiccant package. Stick the package to the inside of the dome cover as indicated. Bosch Security Systems Installation Manual AR18-10-B012 | v1.55 | 2012.09... -
Page 14: Network (And Power) Connector
Use a shielded UTP Category 5e cable with RJ45 connectors (M12 connector for PM version). – Power can be supplied to the camera via the Ethernet cable compliant with the Power-over-Ethernet (IEEE 802.3af) standard. AR18-10-B012 | v1.55 | 2012.09 Installation Manual Bosch Security Systems... -
Page 15: Power Connection
DC12/24V socket of the camera. Connect the power supply to either a 230 VAC or a 120 VAC power supply outlet. Note: A power supply is not included in the package. Bosch Security Systems Installation Manual AR18-10-B012 | v1.55 | 2012.09... -
Page 16: Mounting
Attach the camera and base unit securly to the surface using the two supplied M3 screws. CAUTION! Do not point the camera/lens into direct sunlight as this may damage the sensors. AR18-10-B012 | v1.55 | 2012.09 Installation Manual Bosch Security Systems... -
Page 17: Camera Set-Up
2.5 mm jack socket using a S1460 monitor cable which can be ordered separately. This monitor jack socket provides a composite video signal (NTSC) for installation purposes only. S1460 Monitor Cable Bosch Security Systems Installation Manual AR18-10-B012 | v1.55 | 2012.09... -
Page 18: Camera Positioning
For horizontal adjustment (pan) rotate the camera module in the base. Do not rotate more than 350°. For vertical adjustment (tilt) rotate camera. Do not rotate more than 55°. AR18-10-B012 | v1.55 | 2012.09 Installation Manual Bosch Security Systems... -
Page 19: Resetting The Camera
Position the dome on the base by aligning the two screw holders with fins with the openings beside the screw sockets and slot it home. Use the supplied special screwdriver bit to tighten the three tamper-resistant screws. Bosch Security Systems Installation Manual AR18-10-B012 | v1.55 | 2012.09... -
Page 20: Browser Connection
The camera is configured over the network using the browser. Note: The camera can also be configured using the supplied Bosch Video Client or the Bosch Video Management System. Protected network If a RADIUS server is used for network access control (802.1x authentication), the camera must be configured first. -
Page 21: Troubleshooting
Faulty cable connections. Check all cables, plugs, transmission to contacts and remote location. connections. No connection The unit's configuration. Check all configuration established, no parameters. image transmission. Faulty installation. Check all cables, plugs, contacts and connections. Bosch Security Systems Installation Manual AR18-10-B012 | v1.55 | 2012.09... -
Page 22: Customer Service
MicroDome Camera 200 Series Customer service If a fault cannot be resolved, please contact your supplier or system integrator, or contact Bosch Security Systems Customer Service directly. The Installer should write down all information regarding the unit so that it can be referenced for warranty or repair. The... -
Page 23: Maintenance
Defective or superfluous devices and parts should be disposed of professionally or taken to your local collection point for hazardous materials. Bosch Security Systems Installation Manual AR18-10-B012 | v1.55 | 2012.09... - Page 24 3.74 mm fixed, F2.0 (NDC-284-PT) Audio Input Built-in microphone (NDC-274-P only) Audio compression G.711, L16 (live and recording) Analogue video out 2.5 mm jack for installation only (NTSC) (not for NDC-274-PM) AR18-10-B012 | v1.55 | 2012.09 Installation Manual Bosch Security Systems...
- Page 25 330 g (11.64 oz) approx. IP protection IP66 (PT and PM versions only) Impact protection IK08 (PT and PM versions only) Operating -20 ºC to +50 ºC (-4 ºF to +122 ºF) Temperature Bosch Security Systems Installation Manual AR18-10-B012 | v1.55 | 2012.09...
- Page 26 -20 ºC to +70 ºC (-4 ºF to +158 ºF) Temperature Humidity 10% to 80% relative humidity (non-condensing) 7.1.1 Accessories Contact a Bosch representative in your area for the latest available accessories or visit our website at www.boschsecurity.com AR18-10-B012 | v1.55 | 2012.09 Installation Manual Bosch Security Systems...
- Page 28 Bosch Security Systems www.boschsecurity.com © Bosch Security Systems, 2012...