Operating The Radio; Scan Tuning; Manual Tuning; Storing Stations In Preset Memories - Makita XT1501 Instruction Manual

3. Long press the time set button
2 seconds, display will flash time set symbol
also the hour digit, followed by a beep.
4. Rotate Tuning/Volume control knob to set the required
hour.
5. Press button to confirm hour setting, the minute
digit will flash.
6. Rotate Tuning/Volume control knob to set the required
minute.
7. Press the button again to complete clock setting.

Operating the radio

This radio equips with three tuning methods - Scan tuning,
Manual tuning and Memory presets recall.

Scan Tuning

1. Press the Power button to turn on the radio.
2. Select the required waveband by pressing the Band
button. Make sure the rubber bended rod antenna has
been well placed for best FM reception. For AM (MW)
band, rotate the radio to get best signal. Try to avoid
operating the radio next to computer screen and other
equipment which will cause interference to the radio.
3. Press and release Scan button (long press Scan
button more than 2 seconds will activate time setting),
LCD display will flash Scan symbol and the radio will
search and stop automatically when it finds a radio
station. Press the Scan button again to pick up the
found station.
Note:
A stereo symbol will appear on the display, if the
station found is a stereo station.
Note:
The radio will continue to search next available
stations if you do not press Scan button again when it
finds a radio station.
4. Rotate the Tuning/Volume control knob to get required
sound level. LCD display will show sound level
changes.
Note:
During operating volume control, you can press in
Tuning/Volume control knob to change volume control
to tuning control status.
5. To turn off the radio, press the Power button. Display
will show OFF.

Manual Tuning

1. Press the Power button to turn on the radio.
2. Select the required waveband by pressing the Band
button. Adjust the antenna as described above.
3. A single rotary to the Tuning/Volume control knob will
change the frequency in the following increment:
FM: 50 or 100 kHz
AM (MW): 9 or 10 kHz
8
for more than
and
4. Keep on rotating the Tuning/Volume control knob until
5. Rotate the Tuning/Volume control knob to get required
6. To turn off the radio, press the Power button. Display
Storing stations in preset
memories
There are 5 memory presets for each waveband.
1. Press the Power button to turn on the radio.
2. Tune to required station using one of the methods
3. Press and hold down the required preset until radio
4. Repeat this procedure for the remaining presets.
5. Stations stored in preset memories can be overwritten
Recall stations from preset
memories
1. Press the Power button to turn on the radio.
2. Select the required waveband.
3. Momentarily press the required Preset button, the
Setting the radio alarm
When the radio alarm is selected, the radio will turn on
and play the chosen radio station at the chosen alarm
time. The radio alarm will continue for one hour unless
turned off by pressing the Power button. Pressing the
Power button whilst the alarm is activated will cancel the
alarm for 24 hours.
Note:
When the radio is in low battery status, the radio alarm
can't be activated.
a. Setting radio alarm time:
1. The radio alarm can be set either when radio is on or
2. Press and release radio alarm button
3. During radio alarm symbol flashing, press
4. Display Hour will flash, rotate Tuning/Volume control
5. Follow same procedures of setting hour to set
Note:
If the radio is in volume control status, press in the
tuning/volume control to become Tuning status.
the required frequency shown on the display.
sound level.
will show OFF.
previously described.
beeps. The preset number will appear in the display
and the station will be stored under chosen preset
button.
by following above procedures.
preset number and station frequency will appear in the
display.
off.
radio alarm symbol will flash.
for more than 2 seconds followed by a beep.
knob to select the hour then press
to confirm hour setting.
required minute. Press
time setting.
, the
button
button again
button to complete alarm