Makita GA7061R Instruction Manual
Hide thumbs
Also See for GA7061R:
- Instruction manual (144 pages) ,
- Technical information (25 pages) ,
- Instruction manual (17 pages)
Related Manuals for Makita GA7061R
Summary of Contents for Makita GA7061R
- Page 1 INSTRUCTION MANUAL Angle Grinder GA7061 GA7061R GA9061 GA9061R DOUBLE INSULATION Read before use.
-
Page 2: Specifications
) : 91 dB(A) Sound power level (L ) : 102 dB (A) Uncertainty (K) : 3 dB(A) DOUBLE INSULATION Model GA7061R Sound pressure level (L ) : 91 dB(A) Only for EU countries Sound power level (L ) : 102 dB (A) -
Page 3: Ec Declaration Of Conformity
Work mode: surface grinding with anti vibration side grip Designation of Machine: Angle Grinder Vibration emission (a ) : 6.5 m/s Model No./ Type: GA7061, GA7061R, GA9061, h, AG Uncertainty (K) : 1.5 m/s GA9061R Work mode: disc sanding with normal side grip... -
Page 4: Grinder Safety Warnings
When operating a power tool outdoors, use an Maintain power tools. Check for misalignment extension cord suitable for outdoor use. Use of or binding of moving parts, breakage of parts a cord suitable for outdoor use reduces the risk of and any other condition that may affect the electric shock. - Page 5 cracks, tear or excess wear, wire brush for entering into the pinch point can dig into the surface of loose or cracked wires. If power tool or acces- the material causing the wheel to climb out or kick out. sory is dropped, inspect for damage or install The wheel may either jump toward or away from the an undamaged accessory.
- Page 6 Additional Safety Warnings Specific for Abrasive Be careful not to damage the spindle, the Cutting-Off Operations: flange (especially the installing surface) or the lock nut. Damage to these parts could result in Do not “jam“ the cut-off wheel or apply exces- wheel breakage.
-
Page 7: Functional Description
Do not pull the switch trigger hard released. without pressing in the lock-off button. This can cause switch breakage. Indication lamp Only for model GA7061R / GA9061R ► 1. Switch trigger 2. Lock lever ► 1. Indication lamp 7 ENGLISH... - Page 8 The indication lamp lights up green when the tool is Installing or removing wheel guard plugged. (For depressed center wheel, flap If the indication lamp does not light up, the mains cord disc, flex wheel, wire wheel brush or the controller may be defective. The indication lamp is lit but the tool does not start even / abrasive cut-off wheel, diamond if the tool is switched on, the carbon brushes may be...
- Page 9 ► 1. Wheel guard 2. Bearing box 3. Screw 4. Lever ► 1. Lock nut 2. Depressed center wheel 3. Inner flange 4. Mounting part Pull the lever in direction of the arrow. Then tighten the wheel guard with fastening the screw. Be sure to tighten To tighten the lock nut, press the shaft lock firmly so the screw securely.
-
Page 10: Operation
Super flange CAUTION: Never switch on the tool when it is in contact with the workpiece, it may cause an Optional accessory injury to operator. Only for tools with M14 spindle thread. CAUTION: Always wear safety goggles or a Models with the letter F are standard-equipped with face shield during operation. - Page 11 For Australia and New Zealand Operation with abrasive cut-off / diamond wheel ø45 Optional accessory ø78 WARNING: When using an abrasive cut-off / diamond wheel, be sure to use only the special wheel guard designed for use with cut-off wheels. (In some European countries, when using a diamond wheel, the ordinary guard can be used.
-
Page 12: Maintenance
► 1. Screw MAINTENANCE To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service CAUTION: Always be sure that the tool is Centers, always using Makita replacement parts. switched off and unplugged before attempting to perform inspection or maintenance. -
Page 13: Optional Accessories
The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. Side grip... - Page 16 Makita Jan-Baptist Vinkstraat 2, 3070, Belgium Makita Corporation Anjo, Aichi, Japan 885468-225 www.makita.com 20150826...