Table of Contents
Advertisement
Available languages
Available languages
English
To Re-Fit the Lift+Reach Head
1. Return the handle tube
turn the steam mop OFF.
2. Wait until it cools down. (approximately five minutes)
3. Place the front of your shoe onto the Lift+Reach™ head
cleaning pad removal tab and press down firmly.
4. Lift the Lift+Reach™ head
5. Place the tip of the Lift+Reach™ head into the steam
head
5
and push downward. Ensure it is locked into
place by gently pulling upwards on the handle.
NOTICE: Do not store with a wet pad as this can
damage your floor. Always place the steam mop with
the handle
4
in the upright position when stationary
and make sure the steam mop is turned OFF when
not in use.
Hints for Optimum Use (Fig. A)
WARNING: It is important to monitor the water level
in the water tank. To refill the water tank and continue
to sanitize/ clean, see Filling the Water Tank section.
NOTICE: Never leave the steam mop in one spot on
any surface for any period of time. Do not store with a
wet pad as this can damage your floor. Always place
the steam mop with the handle tube
position when stationary and make sure the steam
mop is turned off when not in use.
•
Always vacuum or sweep the floor before
using the steam mop.
•
The easiest way to use the steam mop is to tilt the
handle to a 45˚ angle and clean slowly, covering a small
area at a time.
•
Do not use chemical cleaners with your steam
mop. To remove stubborn stains from vinyl or linoleum
floors, you can pre-treat them with a mild detergent and
some water before using the steam mop.
Steam Cleaning
1. Place a cleaning pad
facing up.
2. Lightly press the steam mop down onto the cleaning
pad
7
.
3. Plug the steam mop into a wall outlet.
4. Press the ON/OFF switch
15-30 seconds for the steam mop to heat up.
5. Press the steam operate button
steam will start to come out of the steam head.
nOTE: If the system has been run dry it may take up to 45
seconds to prime the system on first use.
6. It takes a few seconds for steam to enter the cleaning
pad. The steam mop will now glide easily over the
surface to be sanitized/cleaned.
7. Push and pull the steam mop slowly across the surface
to thoroughly steam clean each section.
8. When you have finished using the steam mop, return
the handle
4
to the upright position, making sure that
it is supported and turn it OFF.
6
4
to the upright position and
6
up off the cleaning pad.
4
in the upright
7
on the floor with the 'loop' side
1
. It takes approximately
2
. After a few seconds,
9. Wait until the steam mop cools down (approximately
five minutes).
NOTICE: It is important to monitor the water level
in the water tank
continue to sanitize/clean stand the mop upright
making sure that the handle is supported and turn the
steam mop 'OFF' . Unplug the unit from the electrical
wall outlet, refill the water tank
NOTICE: Never leave the steam mop in one spot
on any surface for any period of time. Always place
the steam mop with the handle
upright position when stationary and make sure the
steam mop is turned off when not in use.
After Use (Fig. A, G)
1. Press the steam operation button
press the ON/OFF switch
2. Unplug the steam mop from the electrical wall outlet.
3. Wait until the steam mop cools down
(approximately 15 mins).
4. Empty the water tank.
5. Remove the cleaning pad
6. Clip the power cord around the cord hooks
7. There is a hanging bracket
the hand grip
11
, which allows your steam mop to be
hung from a suitable screw on the wall. Always ensure
that your wall screw is capable of supporting the weight
of the steam mop safely.
MAINTENANCE AND CLEANING
Your BLACK+DECKER corded appliance has been designed
to operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends
upon proper appliance care and regular cleaning.
WARNING: Before performing any maintenance or
cleaning on corded appliances switch off and unplug
the appliance.
•
Clean your appliance using a soft damp cloth. Never
let any liquid get inside the appliance; never immerse
any part of the appliance into a liquid. iMPORTAnT: To
assure product SAFETY and RELIABILITY, repairs,
maintenance and adjustment should be performed
by authorized service centers or other qualified service
organizations, always using identical replacement parts.
•
For stubborn marks you can use a mild solution of soap
and water to dampen your cloth.
Care of the Cleaning Pads
NOTICE: Follow the cleaning instructions printed on
the label of your cleaning pad.
Wash care instructions - Machine wash warm 140 °F (60 °C)
- No bleach - No fabric softener - Air dry only - Allow to dry
fully before re-use.
3
. To refill the water tank and
3
.
4
supported in the
2
to OFF and then
1
to OFF.
7
and wash it for the next use.
9
14
built into the back of
and
10
.
Advertisement
Table of Contents
