Assembly And Adjustments; Specifications - Black & Decker BEPW1700 Instruction Manual

English
Minimum gauge for Cord sets
Total length of Cord in Feet
Volts
120 V 25 (7.6)
240 V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)
Ampere Rating
More not
Than More
Than
0 6 18
6 10 18
10 12 16
12 16 14
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
...................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
OPM .................... oscillations per
minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
Wh ...................... watt hours
Ah ....................... amp hours
Motor
Be sure your power supply agrees with the nameplate
marking. Voltage decrease of more than 10% will cause loss
of power and overheating. These tools are factory tested; if
this tool does not operate, check power supply.

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.

Specifications

Maximum Pounds per Square Inch*
Rated Gallons per Minute*
Electrical Requirements
6
(meters)
50 (15.2) 100 (30.5) 150 (45.7)
American Wire gauge
16 16
16 14
16 14
12 Not Recommended
or AC ........... alternating current
or AC/DC .... alternating or direct
current
...................... Class II Construction
(double insulated)
n o ....................... no load speed
n ......................... rated speed
PSI....................... pounds per square
inch
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation
do not stare into
the light
..................... wear respiratory
protection
..................... wear eye protection
..................... wear hearing
protection
..................... read all
documentation
1700
1.2
120V ~60Hz, 13A
AC
Electrical Cord
High Pressure Hose
Minimum Amp Source
Pressure of Inlet Water
Inlet Water
Soap Consumption Rate
14
*Water flow and maximum pressure ratings determined in accordance with
12
CETA CPC‑100.
12
Attaching Spray Handle (Fig. A, B)
1. To connect the spray wand
insert the end of the spray wand onto the end of the
spray handle.
2. Press in and turn the spray handle counterclockwise to
lock it into position.
Attaching High Pressure Hose (Fig. C)
NOTICE: Never pull high pressure hose or water supply
hose to move pressure washer. This could damage hose
and/or pump inlet and/or pump outlet.
1. To connect the high pressure hose
spray handle
inlet coupler
2. To connect the high pressure hose to the pressure
washer unit
pressure water outlet
nOTE: Uncoil the high pressure hose before installation
to prevent kinks.
nOTE: Avoid cross threading when installing the hose.
Cross threading will cause leaks.
Attaching Garden Hose (Fig. D)
nOTE: Before connecting the garden hose to the pressure
washer unit, run water through the garden hose for thirty
seconds to clear any debris from inside the garden hose.
1. To connect a garden hose to the
pressure washer unit
garden hose
2. Securely tighten the garden hose by hand.
nOTE: Always disconnect the garden hose after usage.
Attaching Nozzles (Fig. E)

DANGER: Risk of fluid injection. Do not direct
discharge stream toward persons, unprotected skin,
eyes or any pets or animals. Serious injury will occur.

WARNING: Flying objects could cause risk of serious
injury. DO NOT attempt to change nozzles while
pressure washer is running. Turn pressure washer unit
OFF before changing nozzles.
1. To connect a nozzle to the spray wand
connect collar
appropriate nozzle.
2. Release the quick connect collar to lock the nozzle in place.
3. Give the nozzle a firm tug after the quick connect collar
has locked into place to ensure the nozzle is locked
into place.
2 to the spray handle
1
4 , screw the hose collar
23 .
8 , screw the hose collar
12 .
8 , place the end of the
24 inside the water intake
3 toward the spray wand and insert the
35 ft. (10.6 m)
25 ft. (7.6 m)
15A
20‑100 PSI
Cold Tap
10% MAX
4 ,
to the
22 onto the
22 onto the high
11 .
2 , pull the quick