Makita 5007N Instruction Manual
Hide thumbs
Also See for 5007N:
- Instruction manual (33 pages) ,
- Instruction manual (33 pages) ,
- Instruction manual (33 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita 5007N
Summary of Contents for Makita 5007N
- Page 1 INSTRUCTION MANUAL Circular Saw 5007N 5007NF DOUBLE INSULATION Read before use.
-
Page 2: Specifications
Intended use The vibration total value (tri-axial vector sum) deter- mined according to EN62841-2-5: The tool is intended for performing lengthways and Model 5007N crossways straight cuts and miter cuts with angles in Work mode: cutting wood wood while in firm contact with the workpiece. Vibration emission (a ) : 2.5 m/s... -
Page 3: General Power Tool Safety Warnings
Personal safety General power tool safety warnings Stay alert, watch what you are doing and use common sense when operating a power tool. WARNING: Read all safety warnings, instruc- Do not use a power tool while you are tired or tions, illustrations and specifications provided under the influence of drugs, alcohol or med- with this power tool. -
Page 4: Circular Saw Safety Warnings
Power tool use and care Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. Do not use the power tool if the switch does not turn it on and off. - Page 5 Support large panels to minimise the risk of Never force the saw. Push the saw forward at a blade pinching and kickback. Large panels tend speed so that the blade cuts without slowing. to sag under their own weight. Supports must be Forcing the saw can cause uneven cuts, loss of placed under the panel on both sides, near the line accuracy, and possible kickback.
-
Page 6: Functional Description
Before setting the tool down after completing a FUNCTIONAL DESCRIPTION cut, be sure that the guard has closed and the blade has come to a complete stop. Never attempt to saw with the circular saw CAUTION: held upside down in a vise. This is extremely •... -
Page 7: Switch Action
Setting bevel angle Lighting the lamp (For model 5007NF only) Loosen the lever and tentatively set the tool base at the 0°bevel angle, then tighten the lever securely. Turn the positive stopper so that the arrow on it points one of three positions (22.5°,45°,56°) that is equal to or greater than the desired bevel angle. - Page 8 Be sure the blade is installed with teeth pointing up at the front of the tool. • Use only the Makita wrench to install or remove the blade. To remove the blade, press the shaft lock so that the blade cannot revolve and use the hex wrench to loosen the hex bolt counterclockwise.
-
Page 9: Operation
16. In the event the tool is dropped, it must be tagged and removed from service, and should be inspected by a Makita Factory or Authorized Service Center. ► 1 . Rip fence (Guide rule) The handy rip fence allows you to do extra-accurate straight cuts. -
Page 10: Maintenance
► 1 . Brush holder cap 2. Screwdriver To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be per- ► 1 . Base 2. Adjusting screw formed by Makita Authorized Service Centers, always using Makita replacement parts. ► 1 . Triangular rule 10 ENGLISH... -
Page 11: Optional Accessories
Only use accessory or attachment for its stated purpose. If you need any assistance for more details regard- ing these accessories, ask your local Makita Service Center. • Steel & Carbide-tipped saw blades General purpose blade for fast and smooth rip, Combination crosscuts and miters. - Page 12 Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 884791D934 www.makita.com 20190228...