GE 25841GE3 User Manual

25841 Notes
• This equipment may not be used on coin service provided by the
5.8 GHz Dual Handset Call Waiting telephone company.
• Party lines are subject to state tariffs, and therefore, you may not be able to use
Caller ID Cordless Telephone System
your own telephone equipment if you are on a party line. Check with your local
User's Guide
telephone company.
• Notice must be given to the telephone company upon permanent disconnection
of your telephone from your line.
• If your home has specially wired alarm equipment connected to the telephone
line, ensure the installation of this product does not disable your alarm
equipment. If you have questions about what will disable alarm equipment,
consult your telephone company or a qualified installer.
2 Rights of the Telephone Company
Should your equipment cause trouble on your line which may harm the telephone
network, the telephone company shall, where practicable, notify you that temporary
discontinuance of service may be required. Where prior notice is not practicable and
the circumstances warrant such action, the telephone company may temporarily
discontinue service immediately. In case of such temporary discontinuance, the
telephone company must: (1) promptly notify you of such temporary discontinuance;
(2) afford you the opportunity to correct the situation; and (3) inform you of your
right to bring a complaint to the Commission pursuant to procedures set forth in
Subpart E of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities,
equipment, operations or procedures where such action is required in the operation
of its business and not inconsistent with FCC Rules and Regulations. If these changes
are expected to affect the use or performance of your telephone equipment, the
telephone company must give you adequate notice, in writing, to allow you to
maintain uninterrupted service.
Licensing
Licensed under US Patent 6,427,009.
Hearing Aid Compatibility (HAC)
This telephone system meets FCC standards for Hearing Aid Compatibility.
US NUMBER IS LOCATED ONTHE CABINET BOTTOM
REN NUMBER IS LOCATED ONTHE CABINET BOTTOM
Equipment Approval Information
Your telephone equipment is approved for connection to the Public SwitchedTelephone WARNING:TO
PREVENT FIRE OR
Network and is in compliance with parts 15 and 68, FCC Rules and Regulations and the
ELECTRICAL SHOCK
Technical Requirements forTelephoneTerminal Equipment published by ACTA.
HAZARD, DO NOT
1 Notification to the Local Telephone Company
EXPOSETHIS
On the bottom of this equipment is a label indicating, among other information, the PRODUCT TO RAIN
US number and Ringer Equivalence Number (REN) for the equipment.You must, OR MOISTURE.
upon request, provide this information to your telephone company.
The REN is useful in determining the number of devices you may connect to your
Introduction
telephone line and still have all of these devices ring when your telephone number
is called. In most (but not all) areas, the sum of the RENs of all devices connected
to one line should not exceed 5.To be certain of the number of devices you may
CAUTION: When using telephone equipment, there are basic safety
connect to your line as determined by the REN, you should contact your local
instructions that should always be followed. Refer to the IMPORTANT
telephone company.
SAFETY INSTRUCTIONS provided with this product and save them for
A plug and jack used to connect this equipment to the premises wiring and future reference.
telephone network must comply with the applicable FCC Part 68 rules and
Your Call Waiting Caller ID phone stores and displays specific information, provided
requirements adopted by the ACTA. A compliant telephone cord and modular plug is
by your local telephone company, to subscribers of Caller ID or similar caller
provided with this product. It is designed to be connected to a compatible modular
identification services.
jack that is also compliant. See installation instructions for details.
Your Call Waiting Caller ID phone enables you to:
• Identify callers before you answer the phone.
• View the time and date of each incoming call.
• Record up to 40 Caller ID messages sequentially in each handset.
• Know who called while you were away.
To get the most from your new phone, we suggest that you take a few minutes right
now to read through this user's guide.
IMPORTANT: In order to use all of the features of this unit, you must subscribe
to either the standard Name/Number Caller ID Service or Call Waiting Caller ID
Service. To know who is calling while you are on the phone, you must subscribe
to Call Waiting Caller ID Service.
IMPORTANT: Because cordless phones operate on electricity, you should have
ATLINKS USA, Inc.
at least one phone in your home that isn't cordless, in case the power in your
101 West 103rd Street
home goes out.
Model 25841 Indianapolis, IN 46290
00006031 (Rev. 0 Dom E) © 2005 ATLINKS USA, Inc.
IMPORTANT: You can only use one handset at a time and there is NO
Trademark(s) ® Registered
05-34
conference and intercom features for these units.
Printed in China Marca(s) Registrada(s)
Handset Layout
display
talk/end/call back
(button) Caller ID/vol (+)
(caller ID/volume +
Caller ID/vol (-)
(caller ID/volume
- button)
format/mute
(button)
redial
(button)
headphone jack
ringer
(switch)
(transfer button)
del/chan
(delete/channel button)
flash/prog
(flash/program button)
mem
(memory button)
#pause
*exit
(button)
(button)
Base Layout
page (button)
charge/in use
(indicator)
CAUTION:
Handset Charge Cradle Layout
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THE LIGHTNING CAUTION: TO REDUCE THE THE EXCLAMATION
FLASH AND ARROW RISK OF ELECTRIC SHOCK, DO POINT WITHIN THE
TRIANGLE IS A
HEAD WITHIN THE NOT REMOVE COVER (OR
TRIANGLE IS A BACK). NO USER WARNING SIGN
WARNING SIGN SERVICEABLE PARTS INSIDE. ALERTING YOU OF
ALERTING YOU OF REFER SERVICING TO IMPORTANT
"DANGEROUS QUALIFIED SERVICE INSTRUCTIONS
VOLTAGE" INSIDE PERSONNEL. ACCOMPANYING
THE PRODUCT. THE PRODUCT.
charge
SEE MARKING ON BOTTOM / BACK OF PRODUCT (indicator)
Before You Begin
Parts Checklist
Make sure your package includes the items shown here.
2 Handset 2 Battery
batteries 2 Belt clips compartment doors
AC power
Base Charge cradle converter
Telephone Jack Requirements Wall plate
4. Set the RINGER switch (on the handset) to ON.
To use this phone, you need an RJ11C type modular telephone 5. Plug the AC power adaptor into the electrical outlet and the DC connector into the
jack on the bottom of the base.
jack, which might look like the one pictured here, installed in
Modular
your home. If you don't have a modular jack, call your local 6. Place the handset in the base cradle.The charge/in use indicator turns on, verifying
telephone
phone company to find out how to get one installed. line jack the battery is charging.
Digital Security System 7. Allow the phone to charge for 16 hours prior to first use. If you don't properly charge
the phone, battery performance is compromised.
Your cordless phone uses a digital security system to protect against false ringing,
unauthorized access, and charges to your phone line.
button)
When you place the handset in the base, the unit verifies its security code. After power
outage or battery replacement, you should place the handset in the base for about 20
NOTE : The phone is tone dial only and does not support pulse dial mode.
seconds to reset the code.
INSTALLATION NOTE: Some cordless telephones operate at frequencies that
Extra Charging Cradle
may cause or receive interference with nearby TVs, microwave ovens, and VCRs.
To minimize or prevent such interference, the base of the cordless telephone 1. Plug the AC power adaptor of the extra charging cradle into the electrical outlet.
should not be placed near or on top of a TV, microwave ovens, or VCR. If
2. Install the handset battery as item 2 described above.
trans
such interference continues, move the cordless telephone farther away from
3. Place the handset in the extra charging cradle.The charge indicator turns on,
these appliances.
verifying the battery is charging.
Certain other communications devices may also use the 5.8 GHz frequency for
4. Allow the phone to charge for 16 hours prior to first use.
communication, and, if not properly set, these devices may interfere with each
other and/or your new telephone. If you are concerned with interference, Wall Mounting
please refer to the owner's manual for these devices on how to properly set
channels to avoid interference. Typical devices that may use the 5.8 GHz
frequency for communication include wireless audio/video senders, wireless
computer networks, multi-handset cordless telephone systems, and some long-
range cordless telephone systems.
Installation
Important Installation Guidelines
• Avoid sources of noise and heat, such as motors, fluorescent lighting, microwave
ovens, heating appliances and direct sunlight.
• Avoid areas of excessive dust, moisture and low temperature.
• Avoid other cordless telephones or personal computers.
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the jack is specifically designed
for wet locations. NOTE: For best results, charge the phone on a flat surface before you mount it
on the wall.
• Never touch non-insulated telephone wires or terminals, unless the telephone line
has been disconnected at the network interface.
1. Slip the mounting holes (on the back of the base) over the wall plate posts, and slide
• Use caution when installing or modifying telephone lines. the unit down into place. (Wall plate not included.)
2. Place the handset on the base cradle.
Installing the Phone
Registration
YOU MUST REGISTER BOTH HANDSETS TO THE MAIN BASE BEFORE USE!
a) 1st handset -The 1st handset being charged on the main base station will
automatically register after 16 hours of charging.
b) 2nd handset - After the 2nd handset has charged for 16 hours on the extra charger,
place it on the main base station for 20 seconds, it will then automatically register.
NOTE: PLEASE REGISTER will show on the display if the handsets have not
been registered. Once the handsets have completed registration successfully,
HANDSET 1 and HANDSET 2 will show on the handset's display.
NOTE: In case of a power failure, the handsets may display UNAVAILABLE when
the talk/end/call back button is pressed. You must then place both handsets on
the main base cradle for 20 seconds to re-register.
Base Station
Setup
1. Choose an area near an electrical outlet and a telephone wall jack (RJ11C), and place
your cordless telephone on a level surface, such as a desktop or tabletop, or you
There are four programmable menus available: Language, Area Code, RingerTone, and
may mount it on the wall.
Default Setting.
2. Install the handset battery.
During programming, you may press the flash/prog button at any time to go to the
CAUTION: To reduce the risk of fire or personal injury, use only the next option.To exit the menu, keep the previous setting and return to the standby
battery 5-2548, which is compatible with this unit.
mode, press the *exit button.
NOTE: You must connect the handset battery before use.
Display Language
1. Press the flash/prog button until >1ENG 2FRA 3ESP shows in the display. 1ENG is
BATTERY
the default.
RED WIRE
2. Use the Caller ID/vol (- or +) button or the touch-tone pad on the handset to enter
your selection.
2 Handsets
3. Press flash/prog again to save.
PRESS DOWN
FIRMLY
BLACK WIRE
Local Area Code
• Plug the battery pack cord into the jack located inside the battery compartment, then
1. Press the flash/prog button until AREA CODE - - - shows in the display. - - - is
place the battery pack inside the battery compartment.
the default.
• Put the battery compartment door back on.
2. Use the touch-tone pad on the handset to enter your three digit area code.
3. Plug one end of the telephone line cord into theTEL LINE jack on the bottom of the
3. Press flash/prog again to save.
base and the other end into a modular jack.
Line cord
NOTE: If you make a mistake, press the del/chan button to erase a
wrong number.
Ringer Tone
1. Press the flash/prog button until RINGER TONE 1 shows in the display. 1 is the
default.
2. Use the Caller ID/vol (- or +) button or the touch-tone pad on the handset to scroll to
1, 2, or 3.
CAUTION: Use only the ATLINKS USA, Inc. 5-2501 (black) power
converter that came with this unit. Using other power converters may 3. Press flash/prog to save.
damage the unit.
Default Setting
1. Press the flash/prog button until DEFAULT NO shows in the display. NO is
the default.
2. Use the Caller ID/vol (- or +) button on the handset to scroll to YES or NO.
3. Press flash/prog to save.You will hear a confirmation tone.
Cordless Phone Basics
IMPORTANT: You can only use one handset at a time and there is NO
conference and intercom features for these units.
Charge/In Use Indicator
The phone is ON when the talk/end/call back indicator on the handset and the charge/in
use indicator on the base is lit.The handset and base indicators flash when you receive
a call.
Answering a Call
1. When the phone rings, pick up either handset and press the talk/end/call back button.
2. When finished, press the talk/end/call back button again or place the handset on
either the base cradle or the extra charger to hang up.
Making a Call
1. Pick up either handset and press the talk/end/call back button. Wait for the dial tone.
The call timer starts counting minutes and seconds in the display.
2. Dial a telephone number.
3. When finished, press the talk/end/call back button again or place the handset on
either the base cradle or the extra charger to hang up.
NOTE: You can only use one handset at a time and there is no conference
and intercom features for these units. UNAVAILABLE will be displayed if other
handset is in talk mode.
Pre-dialing
1. Make sure the phone is OFF (not inTALK mode).
2. Dial a telephone number (the number you dial shows in the display).
NOTE: If you make a mistake dialing the number, use the del/chan button to
backspace and erase the wrong number, and enter the correct number.
3. Press the talk/end/call back button on that handset.The number automatically dials
and the call timer starts counting the minutes and seconds in the display.
4. When finished, press the talk/end/call back button again to hang up.
NOTE : You may enter up to 32 pre-dial digits.
Call Transfer
During an external call, you may transfer the external call to another handset.
1. Press trans button on the originating handset. TRANSFERRING shows in the display.
Both handsets will be paged.
2. Press trans button or talk/end/call back on receiving handset to answer the call.
NOTE: To cancel the call transfer, you may press *exit button or trans button on
the originating handset.
NOTE: If there is no answer within 2 minutes after transferring the call, then
both handsets will be rung back (callback). If neither handset answers within 30
seconds, then the external call will be automatically dropped.
Redial
While the phone is ON (inTALK mode), press the redial button to redial the last number
you dialed (up to 32 digits).
OR,
While the phone is OFF (in standby mode), press the redial button and then the
talk/end/call back button to redial the last number.
Flash
Use the flash/prog button to activate custom calling services such as call waiting, which
are available through your local phone company.
TIP: Don't use the talk/end/call back button to activate custom calling services
such as call waiting, or you'll hang up the phone.
Channel Button
While talking on the phone, it may be necessary for you to manually change the
channel to improve reception and reduce noise or static on the line. Press and release
the del/chan button to move to the next clear channel.
Exit
Press the *exit button to cancel any command you initiated.
Finding the Handset
This feature helps locate misplaced handsets.
Press the page button on the base.The handset beeps continuously for about 2 minutes
until you press the talk/end/call back button on the handset or the page button on
the base.
NOTE: You may still page the handsets when the ringer is off.
Ringer Switch
The ringer switch is located on the side of the handset, it has two positions, ON and OFF.
Volume
When the phone is ON (inTALK mode) press the Caller ID/vol (- or +) button to adjust
the listening level. Choose from four volume settings. VOL 1 is the lowest volume and
VOL 4 is the highest volume.
Mute
Use mute during a phone conversation to speak privately and off-line with a third party.
1. Press the format/mute button. MUTE shows in the display.The party on the
telephone will not hear you.
2. Press the format/mute button when finished.
Caller ID (CID)
This unit receives and displays information transmitted by your local phone company.
This information can include the phone number, date, and time; or the name, phone
number, date, and time. Each handset can store up to 40 calls for later review.
Time Date Number of calls
Caller ID phone number Caller ID name
Call Waiting Caller ID
Provided you subscribe to Call Waiting Caller ID service from your phone company,
you are able to see who is calling while you are on the phone when you hear the call
waiting beep.The caller identification information appears in the display after you hear
the tone.
• When you hear the call waiting beep in the handset receiver, press the flash/prog
button to put the current call on hold and answer the incoming call.
IMPORTANT: In order to use this unit's Caller ID features, you must subscribe
to either the standard Name/Number Caller ID Service or Call Waiting Caller ID
Service. To know who is calling while you are on the phone, you must subscribe
to Call Waiting Caller ID Service.
Receiving and Storing CID Records
When you receive a call, the information is transmitted by the phone company to your
Caller ID telephone between the first and second ring.
When the memory is full, a new call automatically replaces the oldest call in memory.
NEW appears in the display for calls received that have not been reviewed.
NOTE: Check with your local phone company regarding name service availability.
Reviewing CID Records
As calls are received and stored, the display is updated to let you know how many calls
have been received.
• Press the Caller ID/vol (-) to scroll through the call records from the most recent
to the oldest.