Parts Description - Makita UB400MP Original Instruction Manual

2. Use power tools only with specifically desig-
nated battery packs. Use of any other battery
packs may create a risk of injury and fire.
3. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another. Shorting the battery termi-
nals together may cause burns or a fire.
Under abusive conditions, liquid may be
4.
ejected from the battery; avoid contact. If con-
tact accidentally occurs, flush with water. If
liquid contacts eyes, additionally seek medical
help. Liquid ejected from the battery may cause
irritation or burns.
5. Do not use a battery pack or tool that is dam-
aged or modified. Damaged or modified batteries
may exhibit unpredictable behaviour resulting in
fire, explosion or risk of injury.
6. Do not expose a battery pack or tool to fire or
excessive temperature. Exposure to fire or tem-
perature above 130 °C may cause explosion.
7. Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specified in the instruc-
tions. Charging improperly or at temperatures
outside the specified range may damage the
battery and increase the risk of fire.
Electrical and battery safety
Do not dispose of the battery(ies) in a fire.
1.
The cell may explode. Check with local codes for
possible special disposal instructions.
Do not open or mutilate the battery(ies).
2.
Released electrolyte is corrosive and may cause
damage to the eyes or skin. It may be toxic if
swallowed.
Do not charge battery in rain, or in wet
3.
locations.
Do not charge the battery outdoors.
4.
5. Do not handle charger, including charger plug,
and charger terminals with wet hands.
Service
1. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
2. Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
First Aid
1. In case of accident make sure that a first-aid
box is available in the vicinity of the opera-
tions. Immediately replace any item taken from
the first aid box.
2. When asking for help, give the following
information:
— Place of accident
— What happened
Number of injured persons
—
— Kind of injuries
— Your name
SAVE THESE INSTRUCTIONS.
WARNING:
with product (gained from repeated use) replace strict
adherence to safety rules for the subject product.
MISUSE or failure to follow the safety rules stated in this
instruction manual may cause serious personal injury.
WARNING:
containing chemicals which may cause respiratory or
other illnesses. Some examples of these chemicals
are compounds found in pesticides, insecticides,
fertilizers and herbicides. Your risk from these expo-
sures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals:
work in a well ventilated area, and work with approved
safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.

PARTS DESCRIPTION

► Fig.3: 1. Cap 2. Pipe 3. Front nozzle
ASSEMBLY
WARNING:
the equipment, switch off the motor or engine and
remove the spark plug cap or battery cartridge.
Otherwise, the fans may move and result in an injury.
WARNING:
equipment, always put it down. Assembling or adjusting the
equipment in an upright position may result in serious injury.
WARNING:
tions in the chapter "SAFETY WARNINGS" and
the instruction manual of the power unit.
Mounting the attachment pipe
CAUTION:
ment pipe is secured after installation. Improper
installation may cause the attachment falling off from
the power unit and cause personal injury.
Mount the attachment pipe to the power unit.
1. Remove the cap from the end of the pipe.
► Fig.4: 1. Pipe 2. Cap
NOTICE:
Do not dispose of the cap since the
cap is necessary for storing the attachment.
2. Turn the lever toward the attachment.
► Fig.5: 1. Lever
3.
Align the pin with the arrow mark on the power
unit. Insert the pipe until the release button pops up.
Make sure that the position line is on the tip of the arrow
mark on the power unit, and the arrow mark on the power
unit and the arrow mark on the pipe are facing each other.
► Fig.6: 1. Release button 2. Arrow mark on the power unit
3. Pin 4. Position line 5. Arrow mark on the pipe
9 ENGLISH
DO NOT let comfort or familiarity
Use of this product can create dust
Before assembling or adjusting
When assembling or adjusting the
Follow the warnings and precau-
Always check that the attach-