Makita UB400MP Original Instruction Manual page 7

Preparation
1. Always wear substantial footwear and long
trousers while operating the blower.
Do not wear loose clothing or jewellery that
2.
can be drawn into the air inlet. Keep long hair
away from the air inlets.
Always wear protective goggles to protect
3.
your eyes from injury when using power tools.
The goggles must comply with ANSI Z87.1 in
the USA, EN 166 in Europe, or AS/NZS 1336
in Australia/New Zealand. In Australia/New
Zealand, it is legally required to wear a face
shield to protect your face, too.
It is an employer's responsibility to enforce
the use of appropriate safety protective equip-
ments by the tool operators and by other per-
sons in the immediate working area.
4. To prevent dust irritation the wearing of a face
mask is recommended.
While operating the machine, always wear
5.
non-slip and protective footwear. Non-skid,
closed-toed safety boots and shoes will reduce the
risk of injury.
6. Wear ear protection, such as ear muffs.
Exposure to noise can cause hearing loss.
Start and operate the engine only outdoors in
7.
a well ventilated area. Operation in a confined or
poorly ventilated area can result in death due to
suffocation or carbon monoxide poisoning.
Operation
1. Clear the area of children, bystanders, and
pets. At a minimum, keep all children, bystand-
ers, and pets outside a 15 m radius; outside
the 15 m zone, there is still a risk of injury
from thrown objects. Bystanders should be
encouraged to wear eye protection. If you are
approached, stop the engine or machine.
► Fig.1
Switch off the blower and remove the battery
2.
cartridge or the spark plug cap, and make sure
that all moving parts have come to a complete
stop
whenever you leave the blower.
•
• before clearing blockages.
• before checking, cleaning or working on
the blower.
• if the blower starts to vibrate abnormally.
3. Operate the blower only in daylight or in good
artificial light.
4. Do not overreach and keep proper balance and
footing at all times.
5. Always be sure of your footing on slopes.
Walk, never run.
6.
7. Keep all cooling air inlets clear of debris.
8. Never blow debris in the direction of
bystanders.
Operate the blower in a recommended position
9.
and on a firm surface.
10. Do not operate the blower at high places.
11. Never point the nozzle at anyone in the vicinity
when using the blower.
12. Never block suction inlet and/or blower outlet.
Be careful not to block suction inlet or
•
blower outlet with dust or dirt when oper-
ating in dusty area.
• Do not use nozzles other than the nozzles
provided by Makita.
• Do not use the blower to inflate balls,
rubber boat or the similar.
13. Do not operate the blower near open window,
etc.
14. Operating the blower only at reasonable hours
is recommended - not early in the morning or
late at night when people might be disturbed.
15. Using rakes and brooms to loosen debris
before blowing is recommended.
16. Before blowing, slightly dampen surfaces in
dusty conditions or use water mist sprayer if
necessary.
17. Adjust the length of the blower nozzle so that
the air stream can work close to the ground.
18. If the blower strikes any foreign objects or
should start making any unusual noise or
vibration, immediately switch off the blower
to stop it. Remove the battery cartridge or the
spark plug cap, and inspect the blower for
damage before restarting and operating the
blower. If the blower is damaged, ask Makita
Authorized Service Centers for repair.
19. Do not insert fingers or other objects into
suction inlet or blower outlet.
20. Prevent unintentional starting. Ensure the
switch is in the off-position before inserting
battery cartridge, picking up or carrying the
blower. Carrying the blower with your finger
on the switch or energizing the blower that has
the switch on invites accidents.
21. Never blow dangerous materials, such as
nails, fragments of glass, or blades.
22. Do not operate the blower near flammable materials.
23. Avoid operating the blower for a long time in
low temperature environment.
24. Before assembling or adjusting the machine,
switch off the motor and remove the spark
plug cap or the battery cartridge.
25. Wear the personal protective equipments
before starting the motor.
26. Before starting the motor, inspect the machine
for damages, loose screws/nuts or improper
assembly. Check all control levers and
switches for easy action. Clean and dry the
handles.
7 ENGLISH