HIKVISION DS-2CD1023G0-IU Quick Start Manual
  1. Manuals
  2. Brands
  3. HIKVISION Manuals
  4. Security Camera
  5. DS-2CD1023G0-IU
  6. Quick start manual

HIKVISION DS-2CD1023G0-IU Quick Start Manual

Network bullet camera
Hide thumbs
Table of Contents

Advertisement

Quick Links

Network Bullet Camera
Quick Start Guide
0

Advertisement

Table of Contents
loading

Related Manuals for HIKVISION DS-2CD1023G0-IU

Summary of Contents for HIKVISION DS-2CD1023G0-IU

  • Page 1 Network Bullet Camera Quick Start Guide...
  • Page 2 Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be "Hikvision"). This user manual (hereinafter referred to be "the Manual") cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.
  • Page 3 LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS.
  • Page 4 Network Bullet Camera·Quick Start Guide IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
  • Page 5 Network Bullet Camera·Quick Start Guide This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
  • Page 6 Network Bullet Camera·Quick Start Guide Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into "Warnings" and "Cautions" Warnings: Serious injury or death may occur if any of the warnings are neglected.
  • Page 7 Network Bullet Camera·Quick Start Guide the restrictions applied to the location and about any precautions that shall be taken. ● Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. ● In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region.
  • Page 8 Network Bullet Camera·Quick Start Guide ● Do not touch sensor modules with fingers. If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an extended period, please replace the lens cap to protect the sensor from dirt.
  • Page 9 Network Bullet Camera·Quick Start Guide ● Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer. ●...

  • Page 10: Table Of Contents

    Network Bullet Camera·Quick Start Guide Table of Contents 1 Appearance Description ............... 10 2 Installation ..................15 Memory Card Installation ..........15 Ceiling Mounting ............16 Wall Mounting with Junction Box ........19 Waterproof Measures ........... 22 2.4.1 Install Network Cable Waterproof Jacket .... 22 2.4.2 Waterproof Other Cables ........

  • Page 11: Appearance Description

    Network Bullet Camera·Quick Start Guide 1 Appearance Description Type I: Type I Bullet Camera Overview Type II: Type II Bullet Camera (PoE) Overview...
  • Page 12 Network Bullet Camera·Quick Start Guide Description Description Mounting Base Back Cover Front Cover IR LED Grounding Power Cord & Network Cable Type III: Type III Bullet Camera Overview Description Description Lens Front Cover...
  • Page 13 Network Bullet Camera·Quick Start Guide Description Back Cover Mounting Base Power Cord Network Cable Type IV: Type IV Bullet Camera Overview Description Description Lens Front Cover Back Cover Mounting Base...
  • Page 14 Network Bullet Camera·Quick Start Guide Description Power Cord Network Cable Type V: Type V Bullet Camera Overview Description Description Lens Front Cover Memory Card Slot Cover Back Cover Mounting Base Power Cord...
  • Page 15 Network Bullet Camera·Quick Start Guide Description Network Cable Note: For cameras support power over Ethernet (PoE), the power is passed along with data on Ethernet cabling. And a switch supports PoE function is required.

  • Page 16: Installation

    Network Bullet Camera·Quick Start Guide 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12VDC, please make sure your power supply matches with your camera.

  • Page 17: Ceiling Mounting

    Network Bullet Camera·Quick Start Guide Unscrew the Cover and Insert Memory Card 2. Insert the memory card into the memory card slot. 3. (Optional)To unmount the memory card, push to get it ejected. 4. Screw the cover back to the camera. Ceiling Mounting Before you start: Both wall mounting and ceiling mounting are suitable for the bullet...
  • Page 18 Network Bullet Camera·Quick Start Guide 2. Drill the screw holes in the ceiling according to the supplied drill template. Note: Drill the cable hole, if adopting ceiling outlet to route the cable. Figure 2-2 The Drill Template 3. Route the cables through the cable hole (optional), or the side opening.
  • Page 19 Network Bullet Camera·Quick Start Guide Note: In the supplied screw package, both self-tapping screws, and  expansion bolts are contained. If the ceiling is cement, expansion bolts are required to fix the  camera. If the ceiling is wooden, self-tapping screws are required. 5.

  • Page 20: Wall Mounting With Junction Box

    Network Bullet Camera·Quick Start Guide 7. (Optional) Install the waterproof jacket. Refer to 2.4 Waterproof Measures for details. Wall Mounting with Junction Box Before you start: Both wall mounting and ceiling mounting are suitable for the  bullet camera. Wall mounting will be taken as an example in this section.
  • Page 21 Network Bullet Camera·Quick Start Guide 3. Take apart the junction box, and align the screw holes of the bullet camera with those on the junction box' cover. 4. Fix the camera on the junction box's cover with three PM4 × 10 screws.
  • Page 22 Network Bullet Camera·Quick Start Guide 6. Route the cables through the cable hole. Here we take bottom cable hole as the example to describe the installation. Separate the water proof cover and the cable gland from the junction box. Route the cable through the bottom cable hole and the cable gland.

  • Page 23: Waterproof Measures

    Network Bullet Camera·Quick Start Guide Waterproof Measures If the camera is installed outdoor, you should use the waterproof accessory or tapes to waterproof the cables. Otherwise the cables might get wet or a short circuit occurs. 2.4.1 Install Network Cable Waterproof Jacket Align Install Waterproof Jacket Figure 2-9...

  • Page 24: Waterproof Other Cables

    Network Bullet Camera·Quick Start Guide 2.4.2 Waterproof Other Cables After routing and connecting the cables, use the waterproof tapes to wrap up the cables. Connected cables and spare cables both should be wrapped up as the figures below. Waterproof Cables...

  • Page 25: Setting The Network Camera Over The Lan

    Network Bullet Camera·Quick Start Guide 3 Setting the Network Camera over the Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection.

  • Page 26: Activating The Camera

    Network Bullet Camera·Quick Start Guide Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We will take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation.

  • Page 27: Activation Via Sadp Software

    Network Bullet Camera·Quick Start Guide Activation Interface(Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
  • Page 28 Network Bullet Camera·Quick Start Guide Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera. Steps: 1. Run the SADP software to search the online devices. 2.

  • Page 29: Modifying The Ip Address

    Network Bullet Camera·Quick Start Guide STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
  • Page 30 Network Bullet Camera·Quick Start Guide Steps: 1. Run the SADP software. 2. Select an active device. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP. Modify the IP Address...
  • Page 31 Network Bullet Camera·Quick Start Guide Note: You can enable the Hik-Connect service for the device during activation. Refer to Chapter 5.1 for detailed information. 4. Input the admin password and click Modify to activate your IP address modification. The batch IP address modification is supported by the SADP. Refer to the user manual of SADP for details.

  • Page 32: Accessing Via Web Browser

    Network Bullet Camera·Quick Start Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps:...
  • Page 33 Network Bullet Camera·Quick Start Guide 4. Click Login. Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in.

  • Page 34: Operating Via Hik-Connect App

    Network Bullet Camera·Quick Start Guide 5 Operating via Hik-Connect App Purpose: Hik-Connect is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so Note: Hik-Connect service is not supported by certain camera models. Enable Hik-Connect Service on Camera Purpose: Hik-Connect service should be enabled on your camera before using...

  • Page 35: Enable Hik-Connect Service Via Web Browser

    Network Bullet Camera·Quick Start Guide Verification Code Setting (SADP) Note: The verification code is required when you add the camera to Hik-Connect app. 3. Click and read "Terms of Service" and "Privacy Policy". 4. Confirm the settings. Enable Hik-Connect Service via Web Browser Before you start: You need to activate the camera before enabling the service.
  • Page 36 Network Bullet Camera·Quick Start Guide Steps: 1. Access the camera via web browser. Refer to Chapter 4. 2. Enter platform access configuration interface: Configuration > Network > Advanced Settings > Platform Access Platform Access Configuration (Web) 3. Select Platform Access Mode as Hik-Connect. 4.

  • Page 37: Hik-Connect Setup

    Network Bullet Camera·Quick Start Guide Hik-Connect Setup Steps: 1. Download and install the Hik-Connect app by searching "Hik-Connect" in App Store or Google Play 2. Launch the app and register for a Hik-Connect user account. 3. Log in Hik-Connect app after registration. Adding Camera to Hik-Connect Before you start: You need to enable the Hik-Connect service on camera before...
  • Page 38 Network Bullet Camera·Quick Start Guide You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package. Figure 5-4 Scan QR Code Note: If the QR code is missing or too blur to be recognized, you can also add the camera by tapping the icon and inputting the camera's serial number.

  • Page 39: Initializing The Memory Card

    Network Bullet Camera·Quick Start Guide Initializing the Memory Card Steps: Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start recording any event triggered video in the camera such as motion detection.
  • Page 40 UD14154B...

Table of Contents