Page 1 HIKVision DS-2DF7284-AEL 2MP Ultra-low Temperature IR Network Speed Dome USER MANUAL IR High-definition Network Speed Dome UD.6L0201D1167A01 www.cctvireland.ie...
Page 2 Certification does not cover the performance or reliability of the security or signaling aspects of this product. UL MAKES NO REPRESENTATIONS, WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.” 0501001030822 © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 3 The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 4  If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the product yourself. (We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.) © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 5  Please use a soft and dry cloth when clean inside and outside surfaces of the product cover. Do not use alkaline detergents.  Improper use or replacement of the battery may result in hazard of explosion. Please use the manufacturer recommended battery type. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 6: Table Of Contents
Configuring Smart Tracking ....................39 Clearing PTZ Configurations ....................40 Chapter 6 Speed Dome Configuration ..................41 Configuring Local Parameters .................... 41 Configuring Time Settings ....................42 Configuring Network Settings.................... 45 © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 7 Configuring IP Address Filter ..................... 98 10.5 Viewing Device Information ....................98 10.6 Maintenance ........................99 10.6.1 Rebooting the Speed Dome ..................99 10.6.2 Restoring Default Settings ..................99 10.6.3 Importing/Exporting Configuration File ..............100 © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 8 User Manual of IR Network Speed Dome 10.6.4 Upgrading the System ..................... 100 10.7 RS-485 Settings ....................... 102 Appendix ............................103 Appendix 1 SADP Software Introduction ..................103 Appendix 2 Port Mapping ......................105 © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 9: Chapter 1 Overview
The dome provides 5 scan modes: auto scan, tilt scan, frame scan, random scan and panorama scan.  Preset Freezing This feature freezes the scene on the monitor when the dome is moving to a preset. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 10 In slow shutter mode, the shutter speed will automatically slow down in low illumination conditions to maintain clear video images by extending the exposure time. The feature can be enabled or disabled.  Backlight Compensation (BLC) © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 11 Comparing with the general 2D digital noise reduction, the 3D digital noise reduction function processes the noise between two frames besides processing the noise in one frame. The noise will be much less and the video will be clearer. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 12: Chapter 2 Network Connection
Figure 2-1.  Refer to the Figure 2-2 to set the network speed dome over the LAN via a switch or a router. Network Cable Figure 2-1 Connecting Directly © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 13: Detecting And Changing The Ip Address
 For accessing the network speed dome from different subnets, please set the gateway for the network speed dome after you logged in. For detailed information, please refer to Section 6.3.1 Configuring TCP/IP Settings. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 14: Setting The Network Speed Dome Over The Wan
Note: Refer to Appendix 2 for detailed information about port mapping. 5. Visit the network speed dome through a web browser or the client software over the internet. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 15: Dynamic Ip Connection
5. Apply a domain name from a domain name provider. 6. Configure the DDNS settings in the setting interface of the router. 7. Visit the speed dome via the applied domain name. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 16 2. Configure the DDNS settings in the DDNS Settings interface of the network speed dome. Refer to Section 6.3.4 Configuring DDNS Settings for detailed configuration. 3. Visit the speed dome via the applied domain name.  Private Domain Name Resolution © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 17 2. Access the network speed dome through the LAN with a web browser or the client software. 3. Enable DDNS and select IP Server as the protocol type. Refer to Section 6.3.4 Configuring DDNS Settings for detailed configuration. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 18: Chapter 3 Access To The Network Speed Dome
The default user name is admin, password is 12345. Figure 3-1 Login Interface 5. Install the plug-in before viewing the live video and operating the speed dome. Please follow the installation prompts to install the plug-in. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 19 User Manual of IR Network Speed Dome Figure 3-2 Download and Install Plug-in Figure 3-3 Install Plug-in (1) Figure 3-4 Install Plug-in (2) © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 20: Accessing By Client Software
Follow the installation prompts to install the client software and WinPcap. The configuration interface and live view interface of client software are shown bellow. Figure 3-6 iVMS-4200 PCNVR Control Panel © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 21  For detailed information about client software of our company, please refer to the user manual of the software. This manual mainly introduces accessing to the network speed dome by web browser. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 22: Chapter 4 Live View
Log in the network speed dome to enter the live view page, or you can click on the menu bar of the main page to enter the live view page. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 23: Starting Live View
Configure the image size and stream type of the live video. 4.3 Starting Live View In the live view window as shown in Figure 4-3, click on the toolbar to start the live view of the speed dome. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 24  Left click a position of the live video. The corresponding position will be moved to the center of the live video.  Hold down the mouse button and drag the mouse to the lower right on left © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 25: Recording And Capturing Pictures Manually
The captured image will be saved as a JPEG file in your computer. 4.5 Operating PTZ Control Purpose: In the live view interface, you can use the PTZ control buttons to control panning, tilting and zooming. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 26: Ptz Control Panel
A preset is a predefined image position. For the defined preset, you can click the calling button to quickly view the desired image position.  Setting a Preset: Steps: 1. In the PTZ control panel, select a preset number from the preset list. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 27 99, the speed dome starts auto scan function. Table 4-3 Special Presets Special Function Special Function Preset Preset Auto flip Set limit stops manually Back to initial position Remote reboot Call patrol 1 Call OSD menu © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 28: Setting / Calling A Patrol
1. In the PTZ control panel, click to enter the patrol settings interface. 2. Select a patrol number from 3. Click to enter the adding interface of preset as shown in Figure 4-8. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 29  Calling a Patrol: In the PTZ control panel, select a defined patrol from and click to call the patrol as shown in Figure 4-9. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 30: Setting / Calling A Pattern
4-11 is displayed on the screen. • Pan the speed dome to the right or left. • Tilt the speed dome up or down. • Zoom in or out. • Refocus the lens. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 31: Configuring Live View Parameters
Please refer to Section 6.4.1 Configuring Video Settings for more detailed parameter settings of the main stream, sub-stream and third stream respectively.  Image Size: You can scale up/down the live view image by clicking . the © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 33: Chapter 5 Ptz Configuration
3. Click Set to save the position. Call/delete an Initial Position:  You can click to call the initial position. You can click delete the initial position and restore the factory default initial position. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 34: Configuring Basic Ptz Parameters
The scan speed can be set from level 1 to 40. PTZ OSD: Set the on-screen display duration of the PTZ status.  © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 35: Configuring Ptz Limit Stops
Configuration > Advanced Configuration > PTZ > Limit Figure 5-3 Configure the PTZ Limit 2. Click the checkbox of Enable Limit and choose the limit type as manual stops or scan stops.  Manual Stops: © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 36: Configuring Scheduled Tasks
3. Set the Park Time. You can set the park time (a period of inactivity) before the dome starts the scheduled tasks. 4. Set the schedule and task details. Steps: (1) Click to edit the task schedule. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 37 (4) Choose the task type from the drop-down list. You can choose scan, preset, pattern and etc. Figure 5-6 Task Types (5) After you set the scheduled task, you can copy the task to other days (Optional). (6) Click to save the settings. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 38: Configuring Park Actions
3. Set the Park Time as the inactivity time of the dome before it starts the park actions. 4. Choose Action Type the from the drop-down list. Figure 5-8 Action Types 5. Click to save the settings. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 39: Configuring Privacy Mask
Click to save the privacy mask, and it will be listed in the Privacy Mask List area; you can select a mask and click to delete it from the list; © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 40: Configuring Smart Tracking
The speed dome tracks the moving objects automatically after you configure this function. Note: The VCA speed domes do not support this function. Steps: 1. Enter the Smart Tracking Settings interface: Configuration > Advanced Configuration> PTZ > Smart Tracking © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 41: Clearing Ptz Configurations
1. Enter the Clearing Configuration interface: Configuration > Advanced Configuration> PTZ > Clear Config 2. Check the checkbox of the items you want to clear. 3. Click to clear the settings. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 42: Chapter 6 Speed Dome Configuration
UDP: Provides real-time audio and video streams. HTTP: Allows the same quality as of TCP without setting specific ports for streaming under some network environments. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 43: Configuring Time Settings
There are Time Zone, Time Synchronization, Daylight Saving Time(DST) functions for setting the time. Time Synchronization consists of auto mode by Network Time Protocol(NTP) server and manual mode. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 44 National Time Center (IP Address: 210.72.145.44). If the speed dome is set in a customized network, NTP software can be used to establish a NTP server for time synchronization. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 45 The time will be adjusted automatically when the Daylight Saving Time(DST) comes. Steps: (1) Enter the DST interface by Configuration > Advanced Configuration > System > DST (2) Check to enable the DST function. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 46: Configuring Network Settings
IPv4 and IPv6 are both supported. Steps: 1. Enter TCP/IP Settings interface: Configuration > Basic Configuration > Network > TCP/IP Or Configuration > Advanced Configuration > Network > TCP/IP © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 47 Preferred DNS Server and Alternate DNS server. Figure 6-8 DNS Server Settings Note: The router must support the route advertisement function if you select Route © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 48: Configuring Port Settings
If you have no router but only a modem, you can use Point-to-Point Protocol over Ethernet (PPPoE) function. Steps: 1. Enter the PPPoE Settings interface: Configuration >Advanced Configuration > Network > PPPoE © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 49: Configuring Ddns Settings
Registration on the DDNS server is required before configuring the DDNS settings of the speed dome. Steps: 1. Enter the DDNS Settings interface: Configuration > Advanced Configuration > Network > DDNS Figure 6-11 DDNS Settings © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 50  HiDDNS: Steps: (1) Enter the Server Address: www.hik-online.com. (2) Enter the Domain name of the camera. The domain is the same with the device alias in the HiDDNS server. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 51: Configuring Snmp Settings
The SNMP version you select should be the same as that of the SNMP software. Steps: 1. Enter the SNMP Settings interface: Configuration > Advanced Configuration > Network > SNMP © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 52: Configuring 802.1X Settings
The speed dome supports IEEE 802.1X standard. IEEE 802.1X is a port-based network access control. It enhances the security level of the LAN. When devices connect to this network with IEEE 802.1X standard, the © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 53 Steps: 1. Connect the network camera to your PC directly with a network cable. 2. Enter the 802.1X Settings interface: Configuration > Advanced Configuration > Network > 802.1X © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 54: Configuring Qos Settings
2. Configure the QoS settings, including video/audio DSCP, event/alarm DSCP and Management DSCP. The valid DSCP value ranges from 0 to 63. The DSCP value is bigger, the priority is higher. 3. Click to save the settings. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 55: Configuring Ftp Settings
Figure 6-20. Figure 6-20 Parent Directory  Child directory: It is a sub-folder which can be created in the parent © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 56: Configuring Upnp™ Settings
Figure 6-22 Configure UPnP Settings 6.3.10 Configuring NAT (Network Address Translation) Settings Steps: 1. Set the port mapping mode: To port mapping with the default port numbers: © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 57: Configuring Email Settings
Please configure the DNS Server settings under Basic Configuration > Network > TCP/IP or Advanced Configuration > Network > TCP/IP before using the Email function. Steps: 1. Enter the Email Settings interface: Configuration > Advanced Configuration > Network > Email © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 58 Attached Image: Check the checkbox of Attached Image if you want to send emails with attached alarm images. Interval: The interval refers to the time between two actions of sending attached pictures. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 59: Configuring Video And Audio Settings
Refer to the Section 6.1 Configuring Local Parameters for switching the main stream and sub-stream for live viewing. 3. You can customize the following parameters for the selected main stream or © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 60: Configuring Audio Settings
Configuration > Basic Configuration > Video / Audio > Audio Or Configuration > Advanced Configuration > Video / Audio > Audio Figure 6-25 Audio Settings 2. Configure the following settings. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 61: Configuring Roi Settings
5. Adjust the ROI level from 1 to 6. The higher the value, the better image quality in the red frame. 6. Enter a Region Name and click Save to save the settings. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 62: Configuring Image Settings
Purpose: You can set the image quality of the speed dome, including brightness, contrast, saturation, sharpness, etc. Notes:  The parameters in Display Settings interface vary depending on the models © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 63 This feature is used to adjust color saturation of the image. The value ranges from 0 to 100.  Sharpness Sharpness function enhances the detail of the image by sharpening the edges in the © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 64  Slow Shutter This function can be used in underexposure condition. It lengthens the shutter time to ensure full exposure. The slow shutter value can be set to Low, Normal and High. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 65 In Night mode, the image is black and white. Night mode can increase the sensitivity in low light conditions. Notes:  When the IR Light Mode is auto, the day/night mode is adjusted © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 66 HLC (High Light Compensation) makes the camera identify and suppress the strong light sources that usually flare across a scene. This makes it possible to see the detail of the image that would normally be hidden. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 67 You can enable or disable the 3D Digital Noise Reduction function as shown in Figure 6-35. The level ranges from 0 to 100. Figure 6-35 3D Digital Noise Reduction This function varies depending on the models of speed dome. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 68: Configuring Osd Settings
20, 40, 80, 160 and 320. This function varies depending on the models of speed dome.  Local Output You can select the output mode to ON or OFF. 6.5.2 Configuring OSD Settings Purpose: © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 69 4. Select from the drop-down list to set the time format, date format and display mode. 5. You can use the mouse to click and drag the text frame in the live view window to adjust the OSD position. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 70: Configuring Text Overlay Settings
4. Use the mouse to click and drag the red text frame in the live view window to adjust the text overlay position. 5. Click Note: There are up to 8 text overlays configurable. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 71: Configuring And Handling Alarms
1. Set the Motion Detection Area. Steps: (1) Enter the motion detection settings interface Configuration > Advanced Configuration> Events > Motion Detection (2) Check the checkbox of Enable Motion Detection. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 72 2. Set the Arming Schedule for Motion Detection. Steps: (1) To edit the arming schedule as shown in Figure 6-42, click Figure 6-41. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 73 (Optional). (5) Click to save the settings. Note: The time of each period can’t be overlapped. Up to 4 periods can be configured for each day. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 74 Send an email with alarm information to a user or users when an event occurs. Note: To send the Email when an event occurs, you need to refer to Section © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 75: Configuring Video Loss Alarm
Section 6.6.5 Configuring Alarm Output to set the alarm output parameters. 6.6.2 Configuring Video Loss Alarm Steps: 1. Enter the Video Loss Setting interface: Configuration > Advanced Configuration> Events > Video Loss Figure 6-44 Video Loss © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 76: Configuring Video Tampering Alarm
1. Enter the tampering Settings interface: Configuration > Advanced Configuration > Events > Video Tampering Figure 6-45 Tamper-proof Alarm 2. Check Enable Video Tampering checkbox to enable the tampering detection. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 77: Configuring External Alarm Input
2. Choose the alarm input No. and the Alarm Type. The alarm type can be NO (Normally Open) and NC (Normally Closed). 3. Edit the name in to set a name for the alarm input (optional). © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 78 No. to enable Preset Calling, Patrol Calling or Pattern Calling. 7. You can copy your settings to other alarm inputs. 8. Click to save the settings. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 79: Configuring Alarm Output
Refer to Step 2 Set the Arming Schedule for Motion Detection in Section 6.6.1 Configuring Motion Detection. 6. You can copy the settings to other alarm outputs. 7. Click to save the settings. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 80: Handling Exception
2. Check the checkbox to set the actions taken for the Exception alarm. Refer to Step 3 Set the Alarm Actions Taken for Motion Detection in Section 6.6.1 Configuring Motion Detection. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 82: Chapter 7 Record Settings
(2) If the status of the disk is Uninitialized as shown in Figure 7-2, check the corresponding checkbox to select the disk and click to start initializing the disk. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 83: Configuring Recording Schedule
By default, the record files of scheduled recording are stored in the SD card (if supported) or in the network disk. Steps: 1. Enter the Record Schedule Settings interface: Configuration > Advanced Configuration> Storage > Record Schedule © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 84  Overwrite: If you enable his function and the HDD is full, the new record files overwrite the oldest record files automatically. Note: The Pre-record and Post-record parameters vary depending on the speed © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 85 Trigger Channel in the Linkage Method of Motion Detection Settings interface. For detailed information, please refer to the Step 1 Set the Motion Detection Area in the Section © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 86 Figure 7-8 Edit Record Schedule (3) Check the checkbox and click to copy settings of this day to the whole week. You can also check any of the checkboxes before the © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 87: Configuring Snapshot Settings
Settings interface. Please refer to Section 6.3.8 Configuring FTP Settings for more details to configure FTP parameters. 2) Check the Enable Timing Snapshot checkbox.  Upload event-triggered snapshots to FTP Steps: © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 88 Detection in Section 6.6.1 Configuring Motion Detection, or Step 4 Configuring External Alarm Input in Section 6.6.1 Configuring Motion Detection. 3) Check the Enable Event-triggered Snapshot checkbox. Figure 7-9 Snapshot Settings © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 89: Chapter 8 Playback
Task 1: To play back the video files Steps: 1. Click on the menu bar to enter playback interface. Figure 8-1 Playback Interface 2. Select the date and click Figure 8-2 Search Video © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 90 Figure 8-4 Set Playback Time Figure 8-5 Progress Bar The different colors of the video on the progress bar stand for the different video © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 91 Task 3: To download the captured pictures Steps: 1. Click on the playback interface. The pop-up menu is shown in Figure 8-8. 2. Set the linkage type of capturing the pictures as timing, alarm, motion, etc.. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 92 3. Set the start time and end time. Click Search. The corresponding picture files are listed on the left. 4. Check the checkbox in front of the files that you need to download. 5. Click to download the files. Figure 8-8 Picture Downloading interface © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 93: Chapter 9 Log Searching
Minor Type, Start Time and End Time as shown in Figure 9-2. 3. Click to search log files. The matched log files will be displayed on the Log interface. Figure 9-2 Log Searching © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 94 User Manual of IR Network Speed Dome 4. To export the log files, click to save the log files in your computer. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 95: Chapter 10 Others
Operator or User. 3. In the Basic Permission field and Camera Configuration field, you can check or uncheck the permissions for the new user. 4. Click to finish the user addition. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 96 2. Modify the User Name, Level or Password. 3. In the Basic Permission field and Camera Configuration field, you can check or uncheck the permissions. 4. Click to finish the user modification. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 97  Delete a User Steps: 1. Left-click the user name you want to delete and click 2. Click on the pop-up dialogue box to delete the user. Figure 10-4 Delete a User © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 98: Configuring Rtsp Authentication
When you enable this function, you can log into the camera without a username and password. In login interface, check the Anonymous checkbox and click Login to enter the camera as shown in Figure 10-7. Figure 10-6 Anonymous Login Figure 10-7 Login Interface © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 99: Configuring Ip Address Filter
Version, Encoding Version, Number of Channels, Number of HDDs, Number of Alarm Input and Number of Alarm Output are displayed. The information cannot be changed in this menu. It is the reference for maintenance or modification in future. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 100: Maintenance
Figure 10-10 Reboot the Device 10.6.2 Restoring Default Settings Steps: 1. Enter the Maintenance interface: Configuration > Basic Configuration> System > Maintenance Or Configuration > Advanced Configuration> System > Maintenance © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 101: Importing/Exporting Configuration File
Figure 10-12 Import/Export Configuration File 10.6.4 Upgrading the System Steps: 1. Enter the Maintenance interface: Configuration > Basic Configuration> System > Maintenance Or Configuration > Advanced Configuration> System > Maintenance © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 102 The upgrading process will take 1 to 10 minutes. Please don't disconnect power of the speed dome during the process. The speed dome reboots automatically after upgrading. Figure 10-13 Remote Upgrade © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 103: Settings
Parity and Flow Control is None. Note: The Baud Rate, PTZ Protocol and PTZ Address parameters of the speed dome should be exactly the same as those of the remote control device. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 104: Appendix
You can also click to refresh the online device list manually. The newly searched devices will be added to the list. Note: You can click on each column heading to order the © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 105 Serial code is a series of characters combined by the start time and the serial number of the device. 2. Input the code in the Serial code field and click to restore the default password. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 106: Appendix 2 Port Mapping
 In the speed dome, the 8200~8210 ports change with the 8000 port with a constant value of 200. E.g. if the 8000 port is changed to 8005, then the 8200~8210 ports should be changed to 8205~8215. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 107 The port of the network speed dome cannot conflict with other ports. For example, some web management port of the router is 80. Change the speed dome port if it is the same as the management port. © Hikvision Digital Technology Co., Ltd. All Rights Reserved. www.cctvireland.ie...
Page 108 www.cctvireland.ie...

HIKVISION DS-2DF7284-AEL User Manual

Chapter 1 Overview

Chapter 2 Network Connection

Chapter 3 Access to the Network Speed Dome

Chapter 4 Live View

Chapter 5 PTZ Configuration

Chapter 6 Speed Dome Configuration

Chapter 7 Record Settings

Chapter 8 Playback

Chapter 9 Log Searching

Chapter 10 Others

Appendix

Appendix 1 SADP Software Introduction

Appendix 2 Port Mapping

Quick Links

Summary of Contents for HIKVISION DS-2DF7284-AEL

Table of Contents