Summary of Contents for HIKVISION DS-K3G411 Series
Page 1
DS-K3G411 Series Tripod Turnstile Quick Start Guide...
Page 2
WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES,...
Page 3
During the use of device, personal data will be collected, stored and processed. To protect data, the development of Hikvision devices incorporates privacy by design principles. For example, for device with facial recognition features, biometrics data is stored in your device with encryption method;...
Page 4
DS-K3G411 Series Tripod Turnstile Quick Start Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Page 5
DS-K3G411 Series Tripod Turnstile Quick Start Guide under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points.
Page 6
DS-K3G411 Series Tripod Turnstile Quick Start Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions: Dangers: Neglecting any of the warnings may cause serious injury or death.
Page 7
DS-K3G411 Series Tripod Turnstile Quick Start Guide This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children.
Page 8
DS-K3G411 Series Tripod Turnstile Quick Start Guide • Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise (which is not a malfunction however), and affecting the endurance of sensor at the same time.
Page 9
DS-K3G411 Series Tripod Turnstile Quick Start Guide Available Models Product Name Model Tripod Turnstile DS-K3G411 Scan the QR code to get User Manual of Tripod Turnstile. Note that mobile data charges may apply if Wi-Fi is unavailable. Figure 1-1 QR Code...
DS-K3G411 Series Tripod Turnstile Quick Start Guide Contents Chapter 1 Overview ........................1 1.1 Introduction ........................... 1 1.2 Main Features ........................1 Chapter 2 System Wiring ......................3 Chapter 3 Installation ......................... 5 3.1 Disassemble Pedestals ......................5 3.2 Install Pedestals ........................5 Chapter 4 General Wiring ......................
Page 11
DS-K3G411 Series Tripod Turnstile Quick Start Guide Chapter 6 Activation ......................... 35 6.1 Activate via SADP ......................... 35 6.2 Activate Device via Client Software ..................36 Appendix A. Tips When Collecting/Comparing Face Picture ............38 Appendix B. Tips for Scanning Fingerprint ................. 39 Appendix C.
DS-K3G411 Series Tripod Turnstile Quick Start Guide Chapter 1 Overview 1.1 Introduction The tripod turnstile is designed to detect unauthorized entrance or exit. By adopting the turnstile integratedly with the access control system, person should authenticate to pass through the lane via swiping IC or ID card, scanning QR code, etc.
Page 13
DS-K3G411 Series Tripod Turnstile Quick Start Guide • Opens/Closes barrier according to the schedule template • Up to 3000 visitor cards and up to 60,000 cards except for visitor cards can be added • Up to 180,000 presenting card events can be recorded...
DS-K3G411 Series Tripod Turnstile Quick Start Guide Chapter 2 System Wiring The preparation before installation and general wiring. Steps 1. Draw a central line on the installation surface of the left or right pedestal. 2. Draw other parallel lines for installing the other pedestals.
Page 15
DS-K3G411 Series Tripod Turnstile Quick Start Guide Note • The suggested inner diameter of the low voltage conduit is larger than 30 mm. • If the face recognition module are required to be connected on the left lane, you should increase the conduit diameter or bury another conduit for the external cables.
DS-K3G411 Series Tripod Turnstile Quick Start Guide Chapter 3 Installation 3.1 Disassemble Pedestals Before installation, you should use the key to open the pedestals. View the pictures below to find the lock holes. Figure 3-1 Lock Holes 3.2 Install Pedestals...
Page 17
DS-K3G411 Series Tripod Turnstile Quick Start Guide Face recognition terminal installed: If the installation area is too close to the wall, make sure the distance between the pedestal and the wall should be more than 20 mm, or the surface may be scratched.
Page 18
DS-K3G411 Series Tripod Turnstile Quick Start Guide Figure 3-2 Dimension 1. Prepare for the installation tools, check the components, and prepare for the installation base. 2. Drill holes on the ground according to the installation holes on the pedestals and insert the expansion sleeves.
DS-K3G411 Series Tripod Turnstile Quick Start Guide Chapter 4 General Wiring 4.1 Components Introduction By default, basic components of the turnstile are connected well. The turnstile supports wiring the AC electric supply for the whole system's power supply. Note The voltage fluctuation of the electric supply is between 100 VAC and 220 VAC, 50 to 60 Hz.
DS-K3G411 Series Tripod Turnstile Quick Start Guide Warning Terminal PE should connect to a ground wire to avoid hazard when people touching the device. Note • The cable bare part should be no more than 8 mm. If possible, wear an insulation cap at the end of the bare cable.
Page 22
DS-K3G411 Series Tripod Turnstile Quick Start Guide Figure 4-2 Open Side Panel 2. Connect the network cable with the network switch. Figure 4-3 Network Switch Position...
DS-K3G411 Series Tripod Turnstile Quick Start Guide 4.4 Terminal Description 4.4.1 Main Control Board Terminal and BUS Terminal Description Main Control Board Description Figure 4-4 Main Control Board Diagram Table 4-1 Main Control Board Terminal Description Table Interface Name Terminal Name...
Page 25
DS-K3G411 Series Tripod Turnstile Quick Start Guide Interface Name Terminal Name Description Remark Grounding Door 2 Signal Input Fire Input Fire System Input Grounding Event Input CASE1 Event Alarm Input 1 Note Grounding The alarm input hardware interface is CASE2...
Page 26
DS-K3G411 Series Tripod Turnstile Quick Start Guide Interface Name Terminal Name Description Remark RS-485F/RS-232F 485F+ RS-485+ Terminal of Note Face Recognition • The DIP of RS-485 Terminal Accessing card ID is set as 1 (Default) and 4 by default. 1...
Page 27
DS-K3G411 Series Tripod Turnstile Quick Start Guide Interface Name Terminal Name Description Remark Terminal Accessing is for entering, and (Default) 4 is for exiting. • If the visitor card is Grounding configured, you should wire two card readers for the exiting side.
Page 28
DS-K3G411 Series Tripod Turnstile Quick Start Guide Interface Name Terminal Name Description Remark DIP address is 4, and the other is 3. Card Reader 3 can be applied together with the card receiver. The normal user can authenticate on Card Reader 4 and...
Page 29
DS-K3G411 Series Tripod Turnstile Quick Start Guide Interface Name Terminal Name Description Remark Card Reader Buzzer Control Output W1_1 Wiegand Reading Data Input Data1 W0_1 Wiegand Reading Data Input Data0 Grounding Wiegand Card Reader Indicator of Card Note Reader Control Output...
Page 30
DS-K3G411 Series Tripod Turnstile Quick Start Guide Interface Name Terminal Name Color Description PD_485- Blue RS-485- of Light Board Accessing Black Grounding UART 1 (In Card 12 V Power Terminal Reader) PA_485/232+ Yellow RS-485+ of Card Reader Accessing Note (Default)
DS-K3G411 Series Tripod Turnstile Quick Start Guide Interface Name Terminal Name Color Description PB_485/232- Yellow RS-232_TX of Fingerprint Recorder Accessing (Default) Black Grounding 4.4.2 Main Control Board DIP Switch Description You can set the device mode, switch the communication mode between RS-232 and RS-485, initialize the device via the DIP switch on the main control board.
Page 32
DS-K3G411 Series Tripod Turnstile Quick Start Guide The corresponded UART No. of the DIP switch is as follows: Figure 4-6 UART No. Diagram The function of different DIP switches are as follows: Table 4-3 Function of DIP Switch DIP Switch Name DIP Switch Bit UART No.
Page 33
DS-K3G411 Series Tripod Turnstile Quick Start Guide DIP Switch Name DIP Switch Bit UART No. Function Diagram 3 (Memory Mode) / Enable Memory Mode Disable Memory Mode 4 (Keyfob Pairing Enable Keyfob Mode) Pairing Mode Disable Keyfob Pairing Mode 5 to 8 (Passing...
Page 34
DS-K3G411 Series Tripod Turnstile Quick Start Guide DIP Switch Name DIP Switch Bit UART No. Function Diagram Prohibit Entrance and Controlled Exit Prohibit Entrance and Free Exit DIP A 1 to 3 UART 1 ON: UART 1 is RS- 232A Interface...
DS-K3G411 Series Tripod Turnstile Quick Start Guide Figure 4-7 Interface and Corresponded UART No. 4.4.3 RS-485 Wiring Note • When the RS-485 terminal should connect with card reader, the DIP switch for entrance is 1, for exit is 4. • The RS-485 ID should not be duplicated when connecting to multiple RS-485 devices.
DS-K3G411 Series Tripod Turnstile Quick Start Guide Note • There are four RS-485 interfaces, which are for connecting ID card reader, IC card reader, QR code scanner, fingerprint and card reader, card recycler, text screen, fingerprint reader, and face recognition terminal. Take the wiring of RS-485 card reader as an example.
Page 37
DS-K3G411 Series Tripod Turnstile Quick Start Guide...
DS-K3G411 Series Tripod Turnstile Quick Start Guide 4.4.5 Wiegand Wiring Note Connect the OK/ERR/BZ if the access controller should control the LED and buzzer of the Wiegand card reader. 4.4.6 Barrier Control Wiring By default, the barrier has connected with the main control board. If possible, the device can connect with a third party control board to control the third party barriers.
DS-K3G411 Series Tripod Turnstile Quick Start Guide 4.4.7 Alarm Output Wiring Note For details about changing the relay output status via the jumper cap, see Alarm Relay Output Mode (NO/NC) . 4.4.8 Fire Alarm Module Wiring You can view the fire alarm module wiring diagram.
DS-K3G411 Series Tripod Turnstile Quick Start Guide Chapter 5 Device Settings You can also set the turnstile to passing mode and memory mode, pair the keyfob, initialize the hardware, switching between RS-485 communication mode and RS-232 communication mode, and view relay output NO/NC diagram by setting the DIP switch on the main control board.
DS-K3G411 Series Tripod Turnstile Quick Start Guide Note • You can also pair the keyfob via the client software. For details, see Managing Keyfob in User Manual of iVMS-4200 AC Client Software. • Only one turnstile can pair the keyfob. If multiple turnstiles are in the pairing mode, the keyfob will select only one of them to pair.
DS-K3G411 Series Tripod Turnstile Quick Start Guide 2. Disconnect the power and reboot the device. The device buzzer buzzes a long beep. 3. When the beep stopped, plug the jumper cap back. 4. Disconnect the power and power on the device again.
• Get the SADP software from the supplied disk or the official website http:// www.hikvision.com/en/ , and install the SADP according to the prompts. • The device and the PC that runs the SADP tool should be within the same subnet.
DS-K3G411 Series Tripod Turnstile Quick Start Guide Status of the device becomes Active after successful activation. 5. Modify IP address of the device. 1) Select the device. 2) Change the device IP address to the same subnet as your computer by either modifying the IP address manually or checking Enable DHCP.
Page 48
DS-K3G411 Series Tripod Turnstile Quick Start Guide three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you change your password regularly, especially in the high security system, changing the password monthly or weekly can better protect your product.
DS-K3G411 Series Tripod Turnstile Quick Start Guide Appendix A. Tips When Collecting/Comparing Face Picture The position when collecting or comparing face picture is as below: Expression • Keep your expression naturally when collecting or comparing face pictures, just like the expression in the picture below.
DS-K3G411 Series Tripod Turnstile Quick Start Guide Appendix B. Tips for Scanning Fingerprint Recommended Finger Forefinger, middle finger or the third finger. Correct Scanning The figure displayed below is the correct way to scan your finger: You should press your finger on the scanner horizontally. The center of your scanned finger should align with the scanner center.
Page 51
DS-K3G411 Series Tripod Turnstile Quick Start Guide Others If your fingerprint is shallow, or it is hard to scan your fingerprint, we recommend you to use other authentication methods. If you have injuries on the scanned finger, the scanner may not recognize. You can change another...
DS-K3G411 Series Tripod Turnstile Quick Start Guide Appendix C. DIP Switch Description The DIP switch is on the master lane control board. No.1 to No 8 is from the low bit to the high bit. When the switch is towards ON, it means the switch is enabled, otherwise, the switch is off. If you set the DIP switch like the figure displayed below, its binary value is 00001100, and its decimal value is 12.
DS-K3G411 Series Tripod Turnstile Quick Start Guide Appendix E. Table of Audio Index Related Content Index Content Authenticated. Card No. does not exist. Card No. and fingerprint mismatch. Passing timeout. No permissions. Authentication time out. Authentication failed. Expired card.
Device Command Scan the following QR code to get the device common serial port commands. Note that the command list contains all commonly used serial ports commands for all Hikvision access control and video intercom devices. Figure F-2 Device Command...