Table of Contents
Advertisement
Quick Links
MODEL H8172
CEMENT MIXER
OWNER'S MANUAL
(For models manufactured since 10/14)
COPYRIGHT © APRIL, 2007 BY GRIZZLY INDUSTRIAL, INC., REVISED NOVEMBER, 2014 (AW)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#TR9030 PRINTED IN CHINA
V2.11.14
Advertisement
Table of Contents
Related Manuals for Grizzly H8172
Summary of Contents for Grizzly H8172
- Page 1 OWNER'S MANUAL (For models manufactured since 10/14) COPYRIGHT © APRIL, 2007 BY GRIZZLY INDUSTRIAL, INC., REVISED NOVEMBER, 2014 (AW) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
- Page 2 This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.
-
Page 3: Table Of Contents
Table of Contents INTRODUCTION ..........................2 Manual Accuracy ........................2 Contact Info ..........................2 SECTION 1: SAFETY ........................4 Safety Instructions for Machinery ....................4 Additional Safety for Cement Mixers ..................6 SECTION 2: POWER SUPPLY ......................7 SECTION 3: SETUP ......................... 9 Unpacking .......................... -
Page 4: Introduction
Before calling, please write down the Email: manuals@grizzly.com Manufacture Date and Serial Number stamped into the machine ID label (see below). This infor- mation helps us determine if updated documenta- tion is available for your machine. Manufacture Date Serial Number H8172 Cement Mixer... - Page 5 SHeet Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 model H8172 Cement mixer Product Dimensions: Weight ................................... 132 lbs. Length/Width/Height ............................50" x 33" x 54" Shipping Dimensions: Weight ................................... 145 lbs.
-
Page 6: Section 1: Safety
Everyday ery. Never operate under the influence of drugs or eyeglasses are NOT approved safety glasses. alcohol, when tired, or when distracted. H8172 Cement Mixer... - Page 7 Contact our debris. Make sure they are properly installed, Technical Support at (570) 546-9663. undamaged, and working correctly. H8172 Cement Mixer...
-
Page 8: Additional Safety For Cement Mixers
If normal safety respect. Failure to do so could result in serious personal injury, damage to equip- precautions are overlooked or ignored, serious personal injury may occur. ment, or poor work results. H8172 Cement Mixer... -
Page 9: Section 2: Power Supply
H8172 Cement Mixer... - Page 10 1-15 Plug 25 Feet ..........16 AWG 50 Feet ..........14 AWG Neutral 100 Feet ..........12 AWG Over 100 Feet ....Not Recommended Figure 1. Typical 1-15 plug and receptacle. H8172 Cement Mixer...
-
Page 11: Section 3: Setup
Wrench/Socket 13mm ........ 2 tion of your shipment, inventory the contents. • Wrench/Socket 14mm ........ 2 • Wrench/Socket 17mm ........ 1 SUFFOCATION HAZARD! Keep children and pets away from plastic bags or packing materials shipped with this machine. Discard immediately. H8172 Cement Mixer... -
Page 12: Inventory
If you cannot find an item on this list, care- fully check around/inside the machine and packaging materials. Often, these items get lost in packaging materials while unpack- ing or they are pre-installed at the factory. Figure 3. Inventory components (picture 2). -10- H8172 Cement Mixer... -
Page 13: Assembly
(see Figure 5). Lock Washer Hex Bolt Flat Washer 8mm M8-1.25 x 65 Lock Washer 8mm Hex Nut M8-1.25 Hex Nut M8-1.25 Figure 7. Attaching axle bracket to frame. Figure 5. Support leg installation. H8172 Cement Mixer -11-... - Page 14 Repeat this process on the fasten- ers used in Steps 9–10, as well. Hex Bolt M8-1.25 x 60 Figure 9. Bearing block installed over shaft and attached to frame. Figure 11. Lower end of mixing blades attached to lower drum. -12- H8172 Cement Mixer...
- Page 15 10mm flat washer, lock washer, and hex nut from the inside (see Figure 13). Completely tighten all the mixing blade fas- teners now. Figure 15. Tipping wheel attached. Figure 13. Upper part of mixing blades attached to upper drum. H8172 Cement Mixer -13-...
-
Page 16: Test Run
OFF. The motor using this machine BEFORE understanding should run smoothly and without unusual its controls and related safety information. problems or noises. DO NOT operate, or allow others to operate, machine until the information is understood. -14- H8172 Cement Mixer... -
Page 17: Section 4: Operations
Children can hurt themselves if playing on ects. Regardless of the content in this sec- this mixer. If this machine is not stored in tion, Grizzly Industrial will not be held liable a locked facility, always disconnect power for accidents caused by lack of training. -
Page 18: Section 5: Accessories
11-1/2" deep, overall length is 38". results just like the pros. Includes a 11" x 4-1/2" finishing trowel, 14" x 4" finishing trowel, 6" edging trowel and 6" jointing trowel. Figure 19. All-Steel Round-Head Shovel. Figure 17. H0936 Concrete Hand Tools. -16- H8172 Cement Mixer... -
Page 19: Section 5: Maintenance
Cracking and glazing could result in belt failure. This is a common spray mixture used in commer- Replace the belt if such conditions appear. cial concrete construction to prevent sticking. H8172 Cement Mixer -17-... -
Page 20: Section 6: Wiring
Technical Support at (570) 546-9663. The photos and diagrams included in this section are best viewed in color. You can view these pages in color at www.grizzly.com. -18- H8172 Cement Mixer... -
Page 21: Wiring Diagram
Wiring Diagram Motor BLACK WHITE NEUTRAL 110VAC 1-15 PLUG Run Capacitor 16MF 450VAC Switch (Viewed from backside) Figure 21. Switch wiring. H8172 Cement Mixer -19-... -
Page 22: Section 7: Parts
SECTION 7: PARTS Main Breakdown 64 62 69V2 27V2 26 53V2 35V2 67V2 29 28 33 32 34V2 70V2 18 14 15V2 19 18 14 13V2 25V2 25V2 16V2 53V2 57 56 58 60V2 54V2 58-1V2 -20- H8172 Cement Mixer... -
Page 23: Main Parts List
PH8172035V2 LOCK PIN 5 X 40 V2.05.12 PH8172072 FLAT WASHER 12MM PH8172036 BALL BEARING 6206ZZ PH8172073 LOCK WASHER 12MM PH8172037 EXT RETAINING RING 30MM PH8172074 HEX BOLT M12-1.75 X 35 PH8172038 INT RETAINING RING 62MM PH8172075 FLAT WASHER 27MM H8172 Cement Mixer -21-... -
Page 24: Labels & Cosmetics
MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels. -22-... - Page 25 Would you recommend Grizzly Industrial to a friend? _____ Yes _____No Would you allow us to use your name as a reference for Grizzly customers in your area? Note: We never use names more than 3 times. _____ Yes _____No 10.
- Page 26 FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 FOLD ALONG DOTTED LINE Send a Grizzly Catalog to a friend: Name_______________________________ Street_______________________________ City______________State______Zip______ TAPE ALONG EDGES--PLEASE DO NOT STAPLE...
-
Page 27: Warranty & Returns
WARRANTY & RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.