Installation; Storing Accessories - Makita 2712 Instruction Manual

38. Never try to use the tool unless all guards and
other safety devices necessary for tool are in
good working order.
39. Operators must be adequately trained in the
assembly, adjustment and operation of the
tool.
40. Never use the blades which maximum speed is
lower than the no load speed of the tool.
41. Keep work area well lit.
SAVE THESE INSTRUCTIONS.

INSTALLATION

PREPARATION
Check contents of package for the following compo-
nents. Please inform Makita service center of any part
missing in the package immediately.
— Table saw (1 unit)
— Leg (4 pcs)
— Foot (4 pcs)
— Countersunk screw for foot (4 pcs)
— Hex nut for foot (4 pcs)
— Leg support (long) (2 pcs)
— Leg support (short) (2 pcs)
— Tire complete (1 pc)
— Dust nozzle (1 pc)
— Carrying handle (2 pcs)
— Square neck bolt for guide rail (4 pcs)
— Hex bolt for guide rail (4 pcs)
— Guide rail (long) (1 pc)
— Guide rail (short) (1 pc)
— Sub table (1 pc)
— Stay (long) (2 pc)
— Stay (short) (2 pc)
— Hook (1 pc)
— Blade guard (1 pct)
— Tapping screw (3 pcs)
— Hex bolt (38 pcs)
— Hex nut (38 pcs)
— Hex wrench (1 pc)
— Wrench (1 pc)
— Push stick (1 pc)
— Push block (1 pc)
— Fence (for Rip fence) (1 pc)
— Rip fence (1 pc)
Installing table saw
1. Overturn the table saw on two boards. Check
the riving knife positions the space between two
boards.
► Fig.1: 1. Board 2. Riving knife
2. Attach the four legs to the inside of base edge.
Attach the leg with the hole for the switch to the
side with the sign "A "on the base. Secure the four
legs temporarily, do not tighten the screws firmly
yet.
► Fig.2: 1. Leg 2. Switch hole 3. Sign A
3. Attach the leg supports (long) to the legs and then
attach the leg supports (short) to the legs. Secure
the legs and leg supports with the screws firmly.
Always check the direction of support legs.
4. Install the feet at the bottoms of the legs. Secure
them with countersunk screws and hex nuts.
► Fig.3: 1. Leg support (long) 2. Leg support (short)
3. Foot 4. Wider side
5. Install the tire complete to the legs and secure
them with screws and hex nuts.
► Fig.4: 1. Tire complete
6. Install the dust nozzle.
7. Adjust the motor part to the 0°position and secure
it by tightening the knob. Secure the power cord
with the cord clamp.
► Fig.5: 1. Dust nozzle
8. Turn the table saw back and then attach the carry-
ing handles.
► Fig.6: 1. Carrying handle 2. Screw
9. Install the switch to the leg and secure it with the
tapping screws.
► Fig.7: 1. Switch 2. Tapping screw
10. Install the saw blade and blade guard. When
installing them, refer to the Section "Removing or
installing saw blade" and "Installing blade guard".
11. Install the guide rail (short) to the front side of the
table saw and the guide rail (long) to the left side
of the base.
► Fig.8: 1. Guide rail 2. Square neck bolt
12. Install the sub table to the base. Select the proper
length stays depending on the position.
► Fig.9: 1. Sub table 2. Stay (long) 3. Stay (short)
► Fig.10: 1. Sub table 2. Stay (short) 3. Stay (long)
13. Install the hook to the leg.
► Fig.11: 1. Hook
14. Locate the table saw in a well lit and level area
where you can maintain good footing and bal-
ance. It should be installed in an area that leaves
enough room to easily handle the size of your
workpieces.
If there is any tendency for the table saw to tip
over, slide or move during operation, the table saw
should be secured to the floor.

Storing accessories

► Fig.12: 1. Push stick
Push stick and wrenches can be stored on the right side
of the tool.
10 ENGLISH