Honeywell MAXPRO NVR HYBRID SE Quick Install Manual

®
MAXPRO NVR HYBRID SE Quick Install Guide
Document 800-15885V1 – Rev A – 02/2014
Introduction
Welcome to your new Honeywell MAXPRO
box. Before installing your NVR, please read this guide carefully.
Unpack
Check that the items received match those listed on the order form and packing slip. The packing box should include, in
addition to your NVR unit and this guide:
Recovery DVD
MAXPRO NVR Client Software (Single
Site) and Server Software DVD (includes
manuals)
MAXPRO Viewer Multi-Site Viewing
Software Kit (includes DVD and Getting
Started Guide). Not shown.
Note Other peripheral hardware (owner supplied) will also be needed for your installation (such as cameras,
network PoE switch for the camera network, network switch for a client workstation network, a monitor, and an
optional keyboard controller).
Install the Hardware
Mount the MAXPRO NVR Hybrid SE Unit
supplied.
Connect the Hardware
Rear Panel
3
4
5
8 9
6
1
2
7
Connect supplied keyboard
and mouse before powering
up the NVR.
# Connector Connects to...
1 Power switch
2 AC Power Electrical outlet
3 Video Inputs, Outputs (BNC) Analog cameras
4 Control Outputs
5 Alarm Inputs
6 USB Ports (x4) Various devices
7 eSATA
8 LAN1 - Camera Network Port Network
9 USB Ports (x2) Various devices
10 DVI Monitor (with VGA adapter)
Keyboard Controller (Optional) Follow the documentation included with
your IP keyboard controller to connect it to the NVR.
®
NVR HYBRID SE. This guide helps you set up the NVR right out of the
Not shown:
Rack mount ears
DVI-I to VGA adapter
RS485 adapter
I/O connectors
Mount the NVR either on a flat surface or in a rack using the rack mount ears
To access the front LEDs and HDDs (hard
drives), use the security key to unlock, then pull
the front panel toward you.
Connect up to 16 analog
cameras to the Video Input
connectors.
20
21
14–18 22
10
12
11 13
19
Connect a local monitor to
one of the monitor outputs.
# Connector Connects to...
11 HDMI Monitor
12 USB Ports (x2) Various devices
13 Optical output Not supported
14-18 Audio inputs and outputs Line in - line level
Speaker out
Microphone in - not used
19 Optical output Not used
20 RCA connector Spot Monitor (RCA)
21 LAN2 - Client Network Port Network
22 RS485 PTZ device
Network Connections Connect a network PoE switch to the camera network port at the rear of the MAXPRO NVR unit.
Connect your cameras to the network PoE switch with CAT5 Ethernet cables. Optionally, connect the client workstation
network port to your client workstation network via a network switch. This allows remote access to your NVR. The default
client workstation network IP address must be changed to an available static IP address on your client workstation network.
Monitor(s) The MAXPRO NVR HYBRID SE comes with built-in graphics and two types of monitor outputs. The unit
supports connection of a single monitor using either of the outputs.
HDMI Output to TV/Digital monitor
DVI-I Output to TV/Digital monitor
DVI to SVGA Adapter Connect adapter to DVI output, then connect an
analog VGA monitor.
The recommended resolution for your monitor is 1280 x 1024 pixels (minimum 1024 x 768) and display colors of at least 32
bit.
Dual Network Configuration
Local Monitor (not supplied)
®
MAXPRO NVR HYBRID SE
USB
DVI-I /VGA Adapter or HDMI
USB
Camera Network Client Workstation
Port (default Network Port
192.168.1.101) (default 172.25.254.101)
Camera Network PoE Switch Client Workstation Network Switch
CAT5e
CAT5e
CAT5e
CAT5e
CAT5e
HCD2F
H4D2F1
HCD5HIH
HD4HDIH
H3D2F1
HD3HDIH
Honeywell and Third-Party
IP Cameras
Analog Cameras
Contact your dealer to purchase Honeywell IP and analog cameras and encoder.
See More Information for details on supported Honeywell and third-party devices.
Power Up the Unit
Note Honeywell recommends using an uninterruptible power supply (UPS) for the NVR unit, the camera network switch,
and the cameras to ensure that the NVR can continue to record video during a power outage. If you need to monitor
video during a power outage, consider a UPS for the monitor as well.
1. Before powering up the NVR, turn on camera(s) and other devices — such as a network switch or router — connected
to the NVR. It can take up to two minutes for IP cameras to boot up. Online cameras can be easily discovered by the
unit after starting up.
2. Press the power button on the front of the NVR.
Front Panel
Open CD-ROM
drive tray
HDD activity
3. After powering up, you are prompted to log on. The Default user is user name: Administrator, password: Password1.
The user name and password are case sensitive.
The setup wizard starts automatically but may take two minutes. Proceed to
Mobile Devices
Router/
Firewall
Network
Wireless
Router
CAT5e
CAT5e
Client Workstation
HDD drive button
unlocks HDD lever.
Power LED (green). HDD lever opens the HDD
On = system powered up. drive tray. Push in to lock.
RESET
Reset unit
OPEN
HD1
HDD status
HD2
LEDs
OPEN
Green =
HD3
HDD is
operating.
HD4
Red = fan
is off.
Power button Fan status LED
Green = fan is operating.
Red = Fan is not operating.
Honeywell IP Camera Configuration.
Document 800-15885V1 – Rev A –02/2014