Sony HT-MT500 Service Manual page 6

HT-MT500/MT501
NETWORK CONNECTION CHECKING METHOD
When the MB-1610 board or WLAN/BT combo card is replaced,
check the connection of wireless/wired LAN.
1. Checking method of wireless LAN connection
Necessary equipment:
• TV monitor
• Access point supporting WPS
Procedure:
1. Connect this unit with TV monitor.
2. Touch the [ ] button to turn the power on.
1
3. Press the [HOME] button on the remote commander, display
the home screen.
4. Press the [V]/[v] buttons on the remote commander to select
the " Setup", and press the [ ] button on the remote com-
mander.
5. Press the [V]/[v] buttons on the remote commander to select
the "Network Settings", and press the [ ] button on the remote
commander.
6. Press the [V]/[v] buttons on the remote commander to select
the "Internet Settings", and press the [ ] button on the remote
commander.
7. Press the [V]/[v] buttons on the remote commander to select
the "Wireless Setup", and press the [ ] button on the remote
commander.
8. Press the [V]/[v] buttons on the remote commander to select
the "Wi-Fi Protected Setup™ (WPS)", and press the [ ] but-
ton on the remote commander.
9. The message "Start" is displayed.
10. Press the [ ] button on the remote commander, and press the
[WPS] button on the access point.
11. When wireless LAN connection is completed, "Wireless Con-
nection: OK" and "Internet Access: OK" is displayed.
Note: Refer to the Operating Instructions about details of the connection
method.
2. Checking method of wired LAN connection
Necessary equipment:
• TV monitor
• Router
• Network LAN cable
Procedure:
1. Connect this unit with TV monitor.
2. Connect this unit to the router with the network LAN cable.
3. Touch the [ ] button to turn the power on.
1
4. Press the [HOME] button on the remote commander, display
the home screen.
5. Press the [V]/[v] buttons on the remote commander to select
the " Setup", and press the [ ] button on the remote com-
mander.
6. Press the [V]/[v] buttons on the remote commander to select
the "Network Settings", and press the [ ] button on the remote
commander.
7. Press the [V]/[v] buttons on the remote commander to select
the "Internet Settings", and press the [ ] button on the remote
commander.
8. Press the [V]/[v] buttons on the remote commander to select
the "Wired Setup", and press the [ ] button on the remote
commander.
6
9. Press the [V]/[v] buttons on the remote commander to select
the "Auto", and press the [b] button on the remote command-
er.
10. The "The network will be confi gured with the following set-
tings" screen is display, and press the [b] button on the remote
commander.
11. Press the [V]/[v] buttons on the remote commander to select
the "Save & Connect", and press the [ ] button on the remote
commander.
12. When wired LAN connection is completed, "Physical Connec-
tion: OK" and "Internet Access: OK" is displayed.
Note: Refer to the Operating Instructions about details of the connection
method.
NFC CONNECTION CHECKING METHOD
When the MB-1610 board, NFC board or WLAN/BT combo card
is replaced, check the connection of NFC.
Connecting to a Mobile
Device by One-Touch
Function (NFC)
By holding an NFC-compatible mobile
device such as a smartphone or tablet
near the N mark on the main unit, the
system is turned on automatically, then
pairing and BLUETOOTH connection are
performed automatically.
Compatible devices
Smartphones, tablets, and music players
with the NFC function built-in
(OS: Android™ 2.3.3 or later, excluding
Android 3.x)
1
Turn on the NFC function of the
mobile device.
2
Touch the N mark on the main unit
with the mobile device.
Keep touching until the mobile
device vibrates and message
appears on the mobile device.
Follow the on-screen instructions to
complete pairing of the main unit
and mobile device.
BLUETOOTH indicator
3
Make sure that the BLUETOOTH
indicator lights in blue.
A connection between the system
and mobile device has been
established.
4
Start audio playback with the
music app on the connected
mobile device.
Sound is output from the system.
Note: After checking of NFC connection, refer to "RESETTING THE
SYSTEM" on page 4 and delete the Bluetooth pairing information.
5
Adjust the volume.
• Adjust the volume by pressing
+/– on the remote control.
• Adjust the subwoofer volume by
pressing SW +/– on the remote
control (page 26). .
• You can play or pause the content
by using the playback operation
buttons on the remote control.
To stop playback by One-touch
function
Touch the N mark on the main unit with
the mobile device again.
Notes
• Depending on your device, you may need
to perform the following items on your
mobile device in advance.
– Turn on the NFC function.
– Install the "NFC Easy Connect"
application from Google Play™ and
start the application. (The application
may not be available in some countries/
regions.) For details, refer to the
operating instructions of your device.
• This feature does not work with
BLUETOOTH-compatible headphones. To
listen to sound using a BLUETOOTH-
compatible headphones, see "Listening
to Sound of the Connected TV or Device
from Headphones" (page 30). .
• [Bluetooth Mode] is changed to [Receiver]
automatically when making BLUETOOTH
connection with the One-touch function.
Even if the One-touch function is
canceled, the [Bluetooth Mode] setting
remains as [Receiver]. For details about
[Bluetooth Mode], see [Bluetooth
Settings] (page 50).
.
• If your mobile device is a type that goes
into standby mode in response to
magnetic force, it may not be able to be
connected by NFC. When the One-touch
function does not work, connect it by
using the BLUETOOTH function (page 27). .