Page 1 Granit™ XP 199xi Series Models: 1990iSR, 1990iXR, 1991iSR, and 1991iXR Industrial Area-Imaging Scanners and Bases User Guide...
Page 2 Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of HII.
Page 3: Table Of Contents
TABLE OF CONTENTS Customer Support ........................xv Technical Assistance ......................xv Product Service and Repair ....................xv Limited Warranty ........................xv Chapter 1 - Get Started ..................1 About This Manual......................... 1 Unpack Your Device........................1 Features of the Device........................2 1990i/1991i SR Features.....................
Page 4 CTS/RTS Emulation ......................17 ACK/NAK Mode........................17 ® Verifone Ruby Terminal......................17 ® Gilbarco Terminal........................18 Honeywell Bioptic Aux Port .....................18 ® Datalogic™ Magellan Aux Port....................18 Wincor Nixdorf Terminal ......................19 Wincor Nixdorf Beetle™ Terminal ..................19 Wincor Nixdorf RS232 Mode A....................20 Keyboard Country Layout......................20 Keyboard Wedge Modifiers......................27 ALT Mode ..........................27...
Page 5 Scanner-Bioptic ACK/NAK Mode..................37 Scanner-Bioptic ACK/NAK Timeout ................37 Chapter 3 - Cordless System Operation .............39 How the Cordless Charge Base Works.................39 Pair with a Honeywell Vehicle Mount Computer............39 Legacy Mode ...........................39 Compatibility Mode ......................40 Replace a Linked Scanner ......................40 Communication Between the Cordless System and the Host...........................40...
Page 6 About the Battery Status Icon ..................49 Reset Scanner ..........................49 Base Charge Modes........................49 Page ..............................50 Page Mode ..........................50 Page Pitch ..........................51 Error Indicators..........................51 Beeper Pitch - Base Error....................51 Number of Beeps - Base Error ..................52 Scanner Report..........................52 Scanner Address ..........................52 Base or Access Point Address ....................52 Scanner Modes..........................52 Charge Only Mode ........................53 Charge and Link Mode......................53...
Page 7 Batch Mode Transmit Delay ....................64 Multiple Scanner Operation ....................64 Scanner Name..........................65 Application Work Groups ......................66 Application Work Group Selection..................67 Reset the Factory Defaults: All Application Work Groups ..........67 Reset the Custom Defaults: All Application Work Groups ...........68 Use the Scanner with Bluetooth Devices................68 Bluetooth Secure Simple Pairing (SSP)................68 Connect with Bluetooth Device Directly...............69 Virtual Keyboard........................71...
Page 8 Beeper Pitch – Good Read ....................81 Vibrate – Good Read......................82 Beeper Pitch – Error ......................82 Beeper Duration – Good Read..................83 LED – Good Read ........................83 Number of Beeps – Good Read..................83 Number of Beeps – Error....................83 Good Read Delay ........................84 User-Specified Good Read Delay..................84 Trigger Modes ..........................85 Manual Trigger ........................85...
Page 9 2D Reread Delay ........................95 Character Activation ........................95 Activation Character......................96 End Character Activation After Good Read ..............96 Character Activation Timeout...................97 Character Deactivation......................97 Deactivation Character .......................97 Illumination Lights ........................98 Aimer Delay.............................98 User-Specified Aimer Delay....................99 Aimer Mode ............................99 Laser Aimer - Scan Duration ....................99 Centering............................100 Single Code Centering......................100 Custom Centering ......................100...
Page 10 Chapter 5 - Data Edit ...................115 Prefix/Suffix Overview ......................115 Points to Keep In Mind ..................... 115 Add a Prefix or Suffix:......................116 Example: Add a Tab Suffix to All Symbologies............116 Clear One or All Prefixes or Suffixes ................116 Add a Carriage Return Suffix to All Symbologies ..........
Page 11 Chapter 7 - Symbologies................141 All Symbologies..........................142 Message Length Description ....................142 Codabar............................142 Code 39 ............................145 Interleaved 2 of 5........................148 NEC 2 of 5 ............................150 Code 93 ............................151 Straight 2 of 5 Industrial (three-bar start/stop) ............153 Straight 2 of 5 IATA (two-bar start/stop) .................154 Matrix 2 of 5 ..........................155 Code 11 ............................156 Code 128 ............................157...
Page 12 Label Code........................... 183 PDF417............................183 MacroPDF417..........................184 MicroPDF417 ..........................184 GS1 Composite Codes ......................185 GS1 Emulation........................... 186 TCIF Linked Code 39 (TLC39) ..................... 187 QR Code............................188 DotCode............................190 Digimarc Barcode™ ........................191 Data Matrix..........................192 MaxiCode ............................. 194 Aztec Code ...........................
Page 13 IMGBOX Modifiers ......................219 RF Default Imaging Device ....................223 Chapter 9 - Utilities..................225 To Add a Test Code I.D. Prefix to All Symbologies............225 Show Software Revision ......................225 Test Menu.............................225 TotalFreedom..........................226 Application Plug-Ins (Apps)....................226 EZConfig for Scanning Introduction .................227 Configure with EZConfig for Scanning..............227 Reset the Factory Defaults ....................228 Chapter 10 - Serial Programming Commands........229 Conventions ..........................229...
Page 14 USB ............................270 Required Safety Labels ......................271 Scanner ..........................271 CCB22-100BT-03N-BF Base ..................272 Chapter 12 - Maintenance and Troubleshooting ........273 Repairs ............................273 Maintenance..........................273 Clean the Scanner......................273 Clean the Window ......................274 About Disinfectant-Ready Models ................274 Inspect Cords and Connectors ..................
Page 15 Programming Chart ..................291 Granit XP User Guide xiii...
Page 16 Granit XP User Guide...
Page 17: Customer Support
Honeywell International Inc. provides service for all of its products through service centers throughout the world. To obtain warranty or non-warranty service, return your product to Honeywell (postage paid) with a copy of the dated purchase record. To learn more, go to www.honeywellaidc.com...
Page 18 Granit XP User Guide...
Page 19: Chapter 1 - Get Started
Product specifications, dimensions, warranty, and customer support information are also included. Honeywell barcode scanners are factory programmed for the most common termi- nal and communications settings. If you need to change these settings, program- ming is accomplished by scanning the barcodes in this guide.
Page 20: Features Of The Device
Features of the Device 1990i/1991i SR Features Provides extreme performance scanning even on damaged and low-quality bar- codes. The SR is built to survive harsh treatment, including drops and extreme temperatures. Ideally suited to normal near-field scanning operations on 1D and 2D barcodes.
Page 21: Connect With Usb
Connect with USB A scanner or a cordless base can be connected to the USB port of a computer. 1. Connect the appropriate interface cable to the device first, then to the com- puter. Corded Granit XP Scanner USB Connection: 2.
Page 22: Connect With Keyboard Wedge
The unit defaults to a USB PC Keyboard. Refer to page 16 for other USB terminal settings. For additional USB programming and technical information, refer to “USB Applica- tion Note,” available at www.honeywellaidc.com. Connect with Keyboard Wedge A scanner or cordless base can be connected between the keyboard and PC as a “keyboard wedge,”...
Page 23: Connect With Rs232 Serial Port
CCB22-100BT-03N Base Keyboard Wedge Connection: 3. Turn the terminal/computer power back on. The scanner beeps. 4. Verify the scanner or cordless base operation by scanning a barcode from the Sample Symbols, beginning on page 289. The unit defaults to an IBM PC AT and compatibles keyboard wedge interface with a USA keyboard.
Page 24: Connect With Rs485
3. If you are connecting a the base horizontally, make sure the cables are secured in the wireways in the bottom of the cordless base and the base sits flat on a horizontal surface. CCB22-100BT-03N Base RS232 Serial Port Connection: Note: The power supply must be ordered separately, if needed.
Page 25 1. Connect the appropriate interface cable to the device, then to the computer. Corded Granit XP Scanner RS485 Connection: 2. If you are connecting the base horizontally, make sure the cables are secured in the wireways in the bottom of the cordless base and the base sits flat on a horizontal surface.
Page 26: Mount A Ccb22-100Bt-03N Charge Base
Mount a CCB22-100BT-03N Charge Base 2.51 in. 5.31 in. 2 in. 63.7mm 134.92mm 51.17mm 2.36 in. 60mm .84 in. 21.42mm Reading Techniques The Granit XP SR scanners have an aimer that projects a bright red spot/cross and corner indicators that correspond to the scanner’s field of view. The aiming spot/ cross should be centered over the bar code, with the entire bar code falling within the corner indicators.
Page 27: Granit Xp Sr
Granit XP SR Linear Barcodes and 2D matrix symbol with aiming dot. Granit XP User Guide...
Page 28: Granit Xp Xr
Granit XP XR Menu Barcode Security Settings Honeywell scanners are programmed by scanning menu barcodes or by sending serial commands to the scanner. If you want to restrict the ability to scan menu codes, you can use the Menu Barcode Security settings. Contact the nearest tech-...
Page 29: Reset The Custom Defaults
Save code, that entire sequence will be saved to your custom defaults. When you have entered all the commands you want to save for your custom defaults, scan the Save Custom Defaults barcode. Set Custom Defaults Save Custom Defaults Note: When using a cordless system, the Custom Defaults settings apply to all workgroups. Scanning the Save Defaults barcode also causes both the scanner and the base or Access Point to perform a reset and become unlinked.
Page 30 Granit XP User Guide...
Page 31: Chapter 2 - Program The Interface
CHAPTER PROGRAM THE INTERFACE Introduction This chapter describes how to program your system for the desired interface. Program the Interface - Plug and Play Plug and Play barcodes provide instant scanner set up for commonly used inter- faces. Note: After you scan one of the codes, power cycle the host terminal to have the interface in effect.
Page 32: Laptop Direct Connect
Laptop Direct Connect For most laptops, scanning the Laptop Direct Connect barcode allows operation of the scanner in parallel with the integral keyboard. The following Laptop Direct Connect barcode also programs a carriage return (CR) suffix and turns on Emulate External Keyboard (page 29).
Page 33: Usb Ibm Surepos
IBM Port 17 Interface IBM Port 9B HHBCR-2 Interface Each barcode above also programs the following suffixes for each symbology: Symbology Suffix Symbology Suffix EAN 8 Code 39 00 0A 0B EAN 13 Interleaved 2 of 5 00 0D 0B UPC A Code 128 * 00 0A 0B...
Page 34: Usb Pc Or Macintosh Keyboard
No extra configuration (e.g., baud rate) is necessary. Note: If you scan the USB Serial barcode either with an older Honeywell serial driver, or no driver installed, you may no longer be able to scan barcodes. If this happens, either uninstall the older driver versions and install the latest driver, or delete the specific device entry in Device Manager.
Page 35: Cts/Rts Emulation
CTS/RTS Emulation CTS/RTS Emulation On * CTS/RTS Emulation Off ACK/NAK Mode ACK/NAK Mode On * ACK/NAK Mode Off ® Verifone Ruby Terminal Scan the following Plug and Play code to program the scanner for a Verifone Ruby terminal. This barcode sets the baud rate to 1200 bps and the data format to 8 data bits, mark parity bit, 1 stop bit.
Page 36: Gilbarco ® Terminal
Gilbarco Settings Honeywell Bioptic Aux Port Scan the following Plug and Play code to program the scanner for a Honeywell bioptic scanner auxiliary port configuration. This barcode sets the baud rate to 38400 bps and the data format to 8 data bits, no parity, 1 stop bit.
Page 37: Wincor Nixdorf Terminal
Wincor Nixdorf Terminal Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf terminal. This barcode sets the baud rate to 9600 bps and the data format to 8 data bits, no parity, 1 stop bit. Wincor Nixdorf Terminal Settings Wincor Nixdorf Beetle™...
Page 38: Wincor Nixdorf Rs232 Mode A
Wincor Nixdorf RS232 Mode A Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf RS232 Mode A terminal. This barcode sets the baud rate to 9600 bps and the data format to 8 data bits, odd parity, 1 stop bit. The following prefixes are programmed for each symbology: Symbology Prefix...
Page 39 Keyboard Countries (Continued) Belarus Belgium Bosnia Brazil Brazil (MS) Bulgaria (Cyrillic) Bulgaria (Latin) Canada (French legacy) Canada (French) Canada (Multilingual) Croatia Czech Granit XP User Guide...
Page 40 Keyboard Countries (Continued) Czech (Programmers) Czech (QWERTY) Czech (QWERTZ) Denmark Dutch (Netherlands) Estonia Faroese Finland France Gaelic Germany Greek Granit XP User Guide...
Page 41 Keyboard Countries (Continued) Greek (220 Latin) Greek (220) Greek (319 Latin) Greek (319) Greek (Latin) Greek (MS) Greek (Polytonic) Hebrew Hungarian (101 key) Hungary Iceland Irish Granit XP User Guide...
Page 42 Keyboard Countries (Continued) Italian (142) Italy Japan ASCII Kazakh Kyrgyz (Cyrillic) Latin America Latvia Latvia (QWERTY) Lithuania Lithuania (IBM) Macedonia Malta Granit XP User Guide...
Page 43 Keyboard Countries (Continued) Mongolian (Cyrillic) Norway Poland Polish (214) Polish (Programmers) Portugal Romania Russia Russian (MS) Russian (Typewriter) Serbia (Cyrillic) Granit XP User Guide...
Page 44 Keyboard Countries (Continued) Serbia (Latin) Slovakia Slovakia (QWERTY) Slovakia (QWERTZ) Slovenia Spain Spanish variation Sweden Switzerland (French) Switzerland (German) Tatar Turkey F Granit XP User Guide...
Page 45: Keyboard Wedge Modifiers
Keyboard Countries (Continued) Turkey Q Ukrainian United Kingdom United States (Dvorak) United States (Dvorak left) United States (Dvorak right) United States (International) Uzbek (Cyrillic) Keyboard Wedge Modifiers ALT Mode If your barcode contains special characters from the extended ASCII chart, for example, an e with an accent grave (è), you will use ALT Mode.
Page 46: Keyboard Style
If your keystrokes require the ALT key and 3 or 4 characters, scan the 3 Characters or 4 Characters barcode. The data is then output with the special character(s) for values 00-255. Default = Off. * Off 3 Characters 4 Characters Keyboard Style This programs keyboard styles, such as Caps Lock and Shift Lock.
Page 47: Keyboard Conversion
Eurpoe China Automatic Caps Lock is used if you change the Caps Lock key on and off. The soft- ware tracks and reflects if you have Caps Lock on or off. This selection can only be used with systems that have an LED that notes the Caps Lock status (AT key- boards).
Page 48: Control Character Output
Default = Keyboard Conversion Off. * Keyboard Conversion Off Convert All Characters to Upper Case Convert All Characters to Lower Case Control Character Output This selection sends a text string instead of a control character. For example, when the control character for a carriage return is expected, the output would display [CR] instead of the ASCII code of 0D.
Page 49 Windows Mode Prefix/Suffix Off: The scanner sends key combinations for ASCII control characters for values 00-1F, but it does not translate prefix or suffix infor- mation. Support ALT 3 Digit HEX Mode: The scanner sends key combinations for ASCII control characters for values 00-1F transmitted as the ALT key and 3 digits. Default = Control + X Mode Off.
Page 50: Rs232 Modifiers
Numeric Keypad Mode: Sends numeric characters as if entered from a numeric keypad. Default = Off. Numeric Keypad Mode On * Numeric Keypad Mode Off Automatic Direct Connect Mode: This selection can be used if you have an IBM AT style terminal and the system is dropping characters.
Page 51: Rs232 Word Length: Data Bits, Stop Bits, And Parity
2400 4800 9600 19200 38400 57,600 * 115,200 RS232 Word Length: Data Bits, Stop Bits, and Parity Data Bits sets the word length at 7 or 8 bits of data per character. If an application requires only ASCII Hex characters 0 through 7F decimal (text, digits, and punctua- tion), select 7 data bits.
Page 52: Rs232 Receiver Time-Out
7 Data, 1 Stop, Parity Odd 7 Data, 2 Stop, Parity Even 7 Data, 2 Stop, Parity None 7 Data, 2 Stop, Parity Odd 8 Data, 1 Stop, Parity Even * 8 Data, 1 Stop, Parity None 8 Data, 1 Stop, Parity Odd 8 Data, 1 Stop, Parity Mark RS232 Receiver Time-Out The unit stays awake to receive data until the RS232 Receiver Time-Out expires.
Page 53: Rs232 Handshake
RS232 Handshake RS232 Handshaking allows control of data transmission from the scanner using software commands from the host device. When RTS/CTS is turned Off, no data flow control is used. Flow Control, No Timeout: The scanner asserts RTS when it has data to send, and will wait indefinitely for CTS to be asserted by the host.
Page 54: Xon/Xoff
* ACK/NAK Off Scanner to Bioptic Communication The following settings are used to set up communication between Honeywell scan- ners and bioptic scanners. Note: The scanner’s baud rate must be set to 38400 and the RS232 timeout must be set to 3000 in order to communicate with a bioptic scanner.
Page 55: Scanner-Bioptic Packet Mode
Scanner-Bioptic Packet Mode Packet Mode On must be scanned to set the scanner’s format so it is compatible with a bioptic scanner. Default = Packet Mode Off. * Packet Mode Off Packet Mode On Scanner-Bioptic ACK/NAK Mode Bioptic ACK/NAK On must be scanned so the scanner will wait for an ACK or NAK from a bioptic scanner after each packet is sent.
Page 56 Granit XP User Guide...
Page 57: Chapter 3 - Cordless System Operation
Pair with a Honeywell Vehicle Mount Computer A Granit XP SR or Granit XP XR can pair with Honeywell vehicle mounted comput- ers. Scan the EZPairing barcode that is either supplied with the vehicle mount computer, attached to the vehicle mount computer, or displayed on the screen.
Page 58: Compatibility Mode
Compatibility Mode In Compatibility Mode, the scanner can work with HID, SPP, or other Bluetooth profiles. Bluetooth needs to be set manually before scanning this barcode. Compatibility Mode (optional) Replace a Linked Scanner If you need to replace a broken or lost scanner that is linked to a base or an Access Point, scan the Override Locked Scanner barcode below with a new scanner and place that scanner in the base, or scan the Access Point linking barcode.
Page 59: Program The Scanner And Base Or Access Point
When data is scanned, the data is sent to the host system via the base or Access Point. The cordless scanner recognizes data acknowledgment (ACK) from the base or Access Point. If it cannot be determined that the data has been properly sent to the base or Access Point, the scanner issues an error indication.
Page 60: System Conditions
noisy RF environments. The bases (Bluetooth Class 1 or Class 2) provide a commu- nication range of 328 feet (100m) or 33 feet (10m) between the scanner and base or Access Point, depending on the environment. See Flexible Power Management, page 58, for information about controlling this range. System Conditions The components of the cordless system interact in specific ways as you associate a scanner to a base or Access Point, as you move a scanner out of range, bring a...
Page 61: Page Button
Page Button When you press the page button on the base or Access Point, the scanners associ- ated with that base or Access Point will begin beeping (3 short and 1 long beep). If you press the trigger on a scanner that is beeping in response, or press the page button on the base or Access Point a second time, all associated scanners will stop beeping.
Page 62: Charge Information
Replace it after the battery is unable to hold an adequate charge. • If you are not sure if the battery or charger is working properly, send it to Honeywell International Inc. or an authorized service center for inspection. Refer to Customer Support on page xv for additional information.
Page 63: Proper Disposal Of The Battery
• Do not store batteries near fire or other high temperature locations. • Do not store or carry batteries together with metal objects. • Do not expose batteries to water or allow the batteries to get wet. • Do not connect (short) the positive and negative terminals, of the batteries, to each other with any metal object.
Page 64: Scanner Communication And Scanning
Scanner Communication and Scanning The following feedback is provided by the scanner and indicates communication and scanning status. Beeper Cause Normal Operation Green Flash 1 Beep Successful communication or linking Red, Blinking Razz or Error Tone Failed communication Menu Operation Green Flash 2 Beeps Successful menu change...
Page 65: Base/Access Point Communication And Scanning
Battery Icon Scanner Charge Yellow Green Beep Level When the 3 sets of No beep <15% scanner is out flashes of the base and repeatedly has been idle every 3 for 5 seconds seconds 3 sets of No beep <5% flashes repeatedly every 3...
Page 66: Base Charge Status
Base Charge Status When charging the base indicates the progress while the scanner resides in the base. Approximate Expected Charge Level Scans (see note) Green On 100% Green Slow Blink 50-99% Green Fast Blink 30-50% Yellow Fast Blink 0-30% Charging, do not scan Note: The number of scans was measured with a clearly printed UPC code in good light.
Page 67: About The Bluetooth Status Icon
About the Bluetooth Status Icon The blue Bluetooth Icon LED has two behaviors flash and on. The icon will flash when linking to a device then will remain on, indicating the base and scanner are linked and stays on when the scanner is in base. Once the scanner is removed from base, the blue LED stays on for four seconds then turns off.
Page 68: Page Mode
When External or Interface Cable Power is selected, the scanner charges from the base’s external power supply, if there is one. If there is no external power supply to the base, the scanner charges from the interface cable. When External Power Only is selected, the scanner only charges from the base’s external power supply.
Page 69: Page Pitch
Page Pitch When you press the page button on the base or Access Point, the scanners associ- ated with that base or Access Point will begin beeping (see Page Button on page 43). You can set the pitch of the paging beep for each scanner by scanning one of the following barcodes.
Page 70: Number Of Beeps - Base Error
Number of Beeps - Base Error The number of beeps and LED flashes emitted by the base for an error condition can be programmed from 1 - 9. For example, if you program this option to have five error beeps, there will be five error beeps and five LED flashes in response to an error.
Page 71: Charge Only Mode
Charge Only Mode There may be times when you want to charge your scanner, but not link to the base. For example, if a scanner is linked to an Access Point or other Bluetooth device and you need to charge the scanner, but want to retain your existing link. In order to program the base for Charge Only Mode, you must link a scanner to it.
Page 72: Unlink The Scanner
Locked Link Mode - Single Scanner If you link a scanner to a base or an Access Point using the Locked Link Mode, other scanners are blocked from being linked if they are inadvertently placed into the base, or if the Access Point linking barcode is scanned. If you do place a differ- ent scanner into a base, it will charge the scanner, but the scanner will not be linked.
Page 73: Override Locked Scanner
Override Locked Scanner If you need to replace a broken or lost scanner that is linked to a base or an Access Point, scan the Override Locked Scanner barcode below with a new scanner and place that scanner in the base, or scan the Access Point linking barcode. The locked link will be overridden;...
Page 74: Scanner Power Time-Out Timer
The sounds are as follows: Setting Sound 3 long beeps, medium pitch 3 long beeps, high pitch 4 short beeps, medium pitch 4 short beeps, high pitch single chirps, medium pitch 2 chirps, then 1 chirp, medium pitch single chirps, high pitch 2 chirps, then 1 chirp, high pitch Base Alarm Type Scanner Alarm Type...
Page 75 If there are no trigger pulls during the timer interval, the scanner goes into power down mode. Whenever the trigger is enabled, the timer is reset. The scanner will not go into power down mode when it is in the base and charging. Default = 3600 sec- onds.
Page 76: Flexible Power Management
Flexible Power Management If you are experiencing network performance issues, and suspect the scanner is interfering with other devices, you can turn down the power output of the scanner. This reduces the range between the scanner and a base or an Access Point as shown in the following illustration: Scanner 802.11...
Page 77: Batch Mode
Access Point once the scanner is back in range or when the records are manually transmitted. Note: Batch Mode is only supported by the Honeywell Charge and Communication Base (CCB) and Honeywell Access Point (AP). Batch mode has limitations when using multiple scanners to one base or Access Point.
Page 78: Batch Mode Beep
Batch Mode Beep When scanning in Inventory Batch Mode (page 59), the scanner beeps every time a barcode is scanned. When Batch Mode Beep is On, you will also hear a click when each barcode is sent to the host. If you do not want to hear these clicks, scan Batch Mode Beep Off.
Page 79: Batch Mode Quantity
Batch Mode Quantity When in Batch Mode, you may wish to transmit the number of multiple barcodes scanned, rather than a single barcode multiple times. For example, if you scan three barcodes called XYZ with Batch Mode Quantity Off, when you transmit your data it will appear as XYZ three times.
Page 80 1. Scan the quantity 0 barcode to change the quantity to 1030. 2. Scan the quantity 0 barcode to change the quantity to 0300. 3. Scan the quantity 1 barcode to change the quantity to 3001. 4. Scan the quantity 0 barcode to change the quantity to 0010. Default = 1.
Page 81: Batch Mode Output Order
Batch Mode Output Order When batch data is transmitted, select whether you want that data sent as FIFO (first-in first-out), or LIFO (last-in first-out). Default = Batch Mode FIFO. * Batch Mode FIFO Batch Mode LIFO Total Records If you wish to output the total number of barcodes scanned when in Batch Mode, scan Total Records.
Page 82: Transmit Records To Host
Transmit Records to Host If you are operating in Inventory Batch Mode (see Inventory Batch Mode on page 59), you must scan the following barcode to transmit all the stored data to the host system. Transmit Inventory Records Batch Mode Transmit Delay Sometimes when accumulated scans are sent to the host system, the transmission of those scans is too fast for the application to process.
Page 83: Scanner Name
To put the scanner in multiple scanner mode, scan the barcode below. Once you scan this barcode, the scanner is unlinked from the base or Access Point and must either be placed into the base, or you must scan the Access Point linking barcode in order to relink.
Page 84: Application Work Groups
You could assign all the scanners in the retail area to one work group and those in the warehouse to another. Consequently, any desired changes to either the retail or warehouse area would apply to all scanners in that particular work group. Honeywell’s online configuration tool, EZConfig-Scanning (page 226), makes it easy for you to program your system for use with multiple scanners and multiple work groups.
Page 85: Application Work Group Selection
settings for whatever work group to which that the scanner was previously assigned. For example, if the scanner was in work group 1 linked to the first base, it will be placed in work group 1 in the second base with the associated settings. Application Work Group Selection This programming selection allows you to assign a scanner to a work group by scanning the barcode below.
Page 86: Reset The Custom Defaults: All Application Work Groups
Use the Scanner with Bluetooth Devices The scanner can be used either with the charge base or with other Bluetooth devices. Those devices include personal computers, laptops, PDAs, and Honeywell mobility systems devices. Bluetooth Secure Simple Pairing (SSP) Secure Simple Pairing (SSP) allows you to connect simply and securely to other...
Page 87: Connect With Bluetooth Device Directly
version 2.1 or higher. When SSP is on, no PIN is required for pairing. Turn SSP off if you are connecting to a Bluetooth device that is not using a compatible Bluetooth version. Default = Bluetooth SSP On. * Bluetooth SSP On Bluetooth SSP Off Connect with Bluetooth Device Directly Your scanner can be paired with Bluetooth-capable devices, such as personal com-...
Page 88 4. If your device does not automatically pair with the scanner, a PIN is displayed. This PIN must be scanned within 60 seconds. Quickly scan Bluetooth PIN Code below, then scan the numeric barcode(s) for the PIN code from the chart below, then scan Save.
Page 89: Virtual Keyboard
Save Virtual Keyboard Once your scanner has been connected directly to an iPad, smart phone, or laptop, you can toggle the virtual keyboard on your device with a quick double pull of the scanner trigger. Bluetooth HID Keyboard Disconnect If your scanner has been connected directly to an iPad, smart phone, or laptop, you must disconnect it in order to once again communicate with the base or Access Point.
Page 90: Bluetooth Serial Port - Pcs/Laptops
Non-Base BT Connection PDAs/Mobility Systems Devices You may also use the scanner with a PDA or a Honeywell Mobility Systems device. Scan the barcode below and follow the instructions supplied with your Bluetooth device to locate the scanner, and connect with it.
Page 91: Auto Reconnect Mode
Auto Reconnect Mode Auto Reconnect controls whether or not the scanner automatically begins the relink process when a loss of connection is detected. When the Auto Reconnect On barcode is scanned, the scanner begins the relink process immediately, without user intervention. Default = Auto Reconnect On. * Auto Reconnect On Auto Reconnect Off The table below shows the results of the Auto Reconnect On and Off settings:...
Page 92: Relink Time-Out
by this setting. After the maximum number of attempts is reached, the scanner will not attempt to reconnect to a base or an Access Point. Pressing the trigger, scan- ning an Access Point linking barcode, or placing the scanner in the cradle resets the attempt count and the scanner will again try to link.
Page 93: Host Acknowledgment
When the scanner goes out of range, 15 attempts are made to link to the base unit or Access Point. Each attempt consists of approximately 5 seconds of active time followed by 3 seconds of idle time. After 15 cycles (8*15 =120), or about 2 minutes, the scanner stops trying to connect to the base or Access Point, but retains any barcodes that may have been saved in batch mode.
Page 94 • A comma must be used as a terminator. • The host terminal software must be capable of interpreting the barcode data, make decisions based on the data content, and send out appropriate escape commands to the scanner. Escape commands are addressed to the scanner via “Application Work Groups.” Once a command is sent, all scanners in a group respond to that command.
Page 95: Host Ack On/Off
Host ACK On/Off Host ACK On * Host ACK Off Host ACK Timeout You can set a timeout for the length of time the scanner waits for a valid escape command when using Host Acknowledgment Mode. Set the length (in seconds) for a timeout by scanning the following barcode, then setting the timeout (from 1-90 seconds) by scanning digits from the Programming Chart,...
Page 96 Granit XP User Guide...
Page 97: Chapter 4 - Input/Output Settings
CHAPTER INPUT/OUTPUT SETTINGS Power Up Beeper The scanner can be programmed to beep when it’s powered up. If you are using a cordless system, the base can also be programmed to beep when it is powered up. Scan the Off barcode(s) if you don’t want a power up beep. Default = Power Up Beeper On - Scanner.
Page 98: Beep On Bel Character
Beep on BEL Character You may wish to force the scanner to beep upon a command sent from the host. If you scan the Beep on BEL On barcode below, the scanner will beep every time a BEL character is received from the host. Default = Beep on BEL Off. *Beep on BEL Off Beep on BEL On Trigger Click...
Page 99: Beeper Volume - Good Read
Beeper Volume – Good Read The beeper volume codes modify the volume of the beep the scanner emits on a good read. Default = High for Granit XP. Medium * High Beeper Pitch – Good Read The beeper pitch codes modify the pitch (frequency) of the beep the scanner emits on a good read.
Page 100: Vibrate - Good Read
Vibrate – Good Read The scanner vibrates once when a barcode is successfully read, and twice when a programming barcode is successfully read. When a programming barcode is unsuccessful, the scanner emits one long vibration (2 times the Vibrate Duration length).
Page 101: Beeper Duration - Good Read
Beeper Duration – Good Read The beeper duration codes modify the length of the beep the scanner emits on a good read. Default = Normal. * Normal Beep Short Beep Short Beep LED – Good Read The LED indicator can be programmed On or Off in response to a good read. Default = On.
Page 102: Good Read Delay
to an error. To change the number of error beeps, scan the barcode below and then scan a digit (1-9) barcode from the Programming Chart, beginning on page 291, then Save. Default = 1. Number of Error Beeps/LED Flashes Good Read Delay This sets the minimum amount of time before the scanner can read another bar- code.
Page 103: Trigger Modes
Trigger Modes Manual Trigger When in manual trigger mode, the scanner scans until a barcode is read, or until the trigger is released. Two modes are available, Normal and Enhanced. Normal mode offers good scan speed and the longest working ranges (depth of field). Enhanced mode will give you the highest possible scan speed but slightly less range than Normal mode.
Page 104 Trigger Number This sets the number of trigger presses required to activate the Trigger Toggle Mode. Default is 3. 2 Quick Triggers *3 Quick Triggers 4 Quick Triggers Trigger Timing This sets the timing of the trigger presses in order to qualify as a trigger toggle, rather than a regular trigger press.
Page 105: Serial Trigger
Serial Trigger You can activate the scanner either by pressing the trigger, or using a serial trigger command (see Trigger Commands on page 232). You must be in a serial interface mode in order to use serial triggering. Refer to RS232 Serial Port (page 14) or Serial...
Page 106: Presentation Mode
Presentation Mode Presentation Mode uses ambient light and scanner illumination to detect bar- codes. When in Presentation Mode, the LEDs remain dim until a barcode is pre- sented to the scanner, then the aimer turns on and the LEDs turn up to read the code.
Page 107: Presentation Centering
Presentation Centering Use Presentation Centering to narrow the scanner’s field of view when it is in the stand to make sure the scanner reads only those barcodes intended by the user. For instance, if multiple codes are placed closely together, Presentation Centering will insure that only the desired codes are read.
Page 108: Near-Far Camera Modes (Xr Models Only)
Scan Presentation Centering On, then scan one of the following barcodes to change the top, bottom, left, or right of the centering window. Then scan the per- cent you want to shift the centering window from the Programming Chart, begin- ning on page 291, then Save.
Page 109: Near Camera Only
Near Camera Only Near Camera Only Far Camera Only Far Camera Only Automatic Switching Between Near and Far Camera Channels (with steady illumination) Automatic Switching *Default Alternate Switching Between Near and Far Camera Channels (with extra far field illumination) Alternate Switching *Default Granit XP User Guide...
Page 110: Poor Quality Codes
Poor Quality Codes Poor Quality 1D Codes This setting improves the scanner’s ability to read damaged or badly printed linear barcodes. When Poor Quality 1D Reading On is scanned, poor quality linear bar- code reading is improved, but the scanner’s snappiness is decreased, making it less aggressive when reading good quality barcodes.
Page 111: Codegate
* Low Resolution PDF Codes CodeGate™ When CodeGate is On, the trigger is used to allow decoded data to be transmitted to the host system. The scanner remains on, scanning and decoding barcodes, but the barcode data is not transmitted until the trigger is pressed. When CodeGate is Off, barcode data is transmitted when it i decoded.
Page 112: Hands Free Time-Out
Hands Free Time-Out The Scan Stand and Presentation Modes are referred to as “hands free” modes. If the scanner’s trigger is pulled when using a hands free mode, the scanner changes to manual trigger mode. You can set the time the scanner should remain in manual trigger mode by setting the Hands Free Time-Out.
Page 113: User-Specified Reread Delay
User-Specified Reread Delay If you want to set your own length for the reread delay, scan the barcode below, then set the delay (from 0-30,000 milliseconds) by scanning digits from the Programming Chart, beginning on page 291, then Save. User-Specified Reread Delay 2D Reread Delay Sometimes 2D barcodes can take longer to read than other barcodes.
Page 114: Activation Character
transmitted. Scan the On barcode to use character activation, then use Activation Character (page 96) to select the character you will send from the host to start scanning. Default = Off. * Off Activation Character This sets the character used to trigger scanning when using Character Activation Mode.
Page 115: Character Activation Timeout
Character Activation Timeout You can set a timeout for the length of time the illumination remains on and attempting to decode barcodes when using Character Activation Mode. Set the length (in milliseconds) for a timeout by scanning the following barcode, then set- ting the timeout (from 1-300,000 milliseconds) by scanning digits from the Programming Chart, beginning on page 291, then Save.
Page 116: Illumination Lights
Illumination Lights If you want the illumination lights on while reading a barcode, scan the Lights On barcode, below. However, if you want to turn just the lights off, scan the Lights Off barcode. Default = Lights On. Note: This setting does not affect the aimer light. The aiming light can be set using Aimer Mode (page 99).
Page 117: User-Specified Aimer Delay
User-Specified Aimer Delay If you want to set your own length for the duration of the delay, scan the barcode below, then set the time-out by scanning digits (0 - 4,000 ms) from the Programming Chart, beginning on page 291, then Save. Delay Duration Aimer Mode This feature allows you to turn the aimer on and off.
Page 118: Centering
Centering Use Centering to narrow the scanner’s field of view to make sure that when the scanner is hand-held, it reads only those barcodes intended by the user. For instance, if multiple codes are placed closely together, centering will insure that only the desired codes are read.
Page 119 Example: In the example below, the white box is the centering window. The centering window has been set to 20% left, 30% right, 8% top, and 25% bottom. Since Barcode 1 passes through the centering window, it will be read. Barcode 2 does not pass through the centering window, so it will not be read.
Page 120: Preferred Symbology
Bottom of Centering Window Left of Centering Window Right of Centering Window Preferred Symbology The scanner can be programmed to specify one symbology as a higher priority over other symbologies in situations where both barcode symbologies appear on the same label, but the lower priority symbology cannot be disabled. For example, you may be using the scanner in a retail setting to read U.P.C.
Page 121: High Priority Symbology
High Priority Symbology To specify the high priority symbology, scan the High Priority Symbology barcode below. On the Symbology Charts on page 279, find the symbology you want to set as high priority. Locate the Hex value for that symbology and scan the 2 digit hex value from the Programming Chart, beginning on page 291, then Save.
Page 122: Output Sequence Overview
Output Sequence Overview Output Sequence Editor This programming selection allows you to program the scanner to output data (when scanning more than one symbol) in whatever order your application requires, regardless of the order in which the barcodes are scanned. You can define up to 15 barcodes in an output sequence.
Page 123: Output Sequence Editor Commands
5. End Output Sequence Editor Use FF to terminate this string or to begin another output sequence. If you are using barcodes, scan F F. Scan Save to save your entries. Other Programming Selections If you are creating an output sequence using barcodes, scan Discard (page 292) to exit without saving any output sequence changes.
Page 124 code identifier for Code 39 9999 code length that must match for Code 39, 9999 = all lengths start character match for Code 39, 43h = "C" termination string for first code code identifier for Code 128 9999 code length that must match for Code 128, 9999 = all lengths start character match for Code 128, 54h = “T”...
Page 125: Enter Output Sequence
start character match for Code 39, 43h = "C" termination string for first code code identifier for Code 128 9999 code length that must match for Code 128, 9999 = all lengths start character match for Code 128, 54h = “T” termination string for first code code identifier for PDF417 9999...
Page 126: Partial Sequence
Enter Output Sequence Partial Sequence If an output sequence operation is terminated before all your output sequence cri- teria are met, the barcode data acquired to that point is a “partial sequence.” You can define how partial sequences are output using the same types of command strings you used to create output sequences.
Page 127 9999 code length that must match for PDF417, 9999 = all lengths start character match for PDF417, 4Dh = “M” termination string for third code SEQSEP99 separator for each sequence, 99 = all symbologies left bracket (<) right bracket (>) SEQSUF99 separator for suffixes, 99 = all symbologies carriage return...
Page 128 Discard Partial Output Sequence If you want to discard partial sequences when the output sequence operation is terminated before completion, scan Discard Partial Sequence. * Discard Partial Sequence Output Sequence Timeouts You can set a timeout for every code in the output sequence defined by the SEQBLK command.
Page 129 Satisfactory Subset of Full Sequence Timeout Example To specify a subset, list its members using the SEQSAT command and terminate each subset with FF. The members of each subset are specified as single hex digits corresponding to their index within the full sequence, 1 being the first. For exam- ple, to specify two subsets, the first consisting of the first and second code in the sequence and the second subset consisting of the second and third code, use the command SEQSAT12FF23FF.
Page 130: Good Read Tone - Output Sequences
Good Read Tone - Output Sequences The scanner may be programmed to either beep or click in response to a good read of each barcode in an output sequence, or to emit a beep or error tone for a partial sequence.
Page 131: No Read
No Read With No Read turned On, the scanner notifies you if a code cannot be read. If using an EZConfig-Scanning Tool Scan Data Window (see page 227), an “NR” appears when a code cannot be read. If No Read is turned Off, the “NR” will not appear. Default = Off.
Page 132: Working Orientation
* Video Reverse Off Working Orientation Some barcodes are direction-sensitive. For example, KIX codes and OCR can mis- read when scanned sideways or upside down. Use the working orientation settings if your direction-sensitive codes will not usually be presented upright to the scan- ner.
Page 133: Chapter 5 - Data Edit
CHAPTER DATA EDIT Prefix/Suffix Overview When a barcode is scanned, additional information is sent to the host computer along with the barcode data. This group of barcode data and additional, user-defined data is called a “message string.” The selections in this section are used to build the user-defined data into the message string.
Page 134: Add A Prefix Or Suffix
• When setting up for specific symbologies (as opposed to all symbologies), the specific symbology ID value counts as an added prefix or suffix character. • The maximum size of a prefix or suffix configuration is 200 characters, which includes header information. Add a Prefix or Suffix: Step 1.
Page 135: Add A Carriage Return Suffix To All Symbologies
Step 1. Scan the Clear One Prefix or Clear One Suffix symbol. Step 2. Determine the 2 digit hex value from the Symbology Chart (included in Symbology Charts, beginning on page 279) for the symbology from which you want to clear the prefix or suffix. Step 3.
Page 136: Function Code Transmit
Clear All Suffixes Function Code Transmit By default, all ASCII control characters are transmitted with barcode data. These non-printable characters are translated into predefined key strokes, or CTRL+X functions (see ASCII Conversion Chart (Code Page 1252), beginning on page 282). If these key strokes interfere with your host’s software application, scan Disable to keep these ASCII control characters from being transmitted.
Page 137: User Specified Intercharacter Delay
To remove this delay, scan the Intercharacter Delay barcode, then set the number of delays to 0. Scan the Save barcode from the Programming Chart, beginning on page 291. Note: Intercharacter delays are not supported in USB serial emulation. User Specified Intercharacter Delay An intercharacter delay of up to 5000 milliseconds (in 5ms increments) may be placed after the transmission of a particular character of scanned data.
Page 138: Intermessage Delay
To remove this delay, scan the Interfunction Delay barcode, then set the number of delays to 0. Scan the Save barcode from the Programming Chart, beginning on page 291. Intermessage Delay An intermessage delay of up to 5000 milliseconds (in 5ms increments) may be placed between each scan transmission.
Page 139: Chapter 6 - Data Format
CHAPTER DATA FORMAT Data Format Editor Introduction You may use the Data Format Editor to change the scanner’s output. For example, you can use the Data Format Editor to insert characters at certain points in bar- code data as it is scanned. The selections in the following pages are used only if you wish to alter the output.
Page 140: Show Data Format
If you have changed data format settings, and wish to clear all formats and return to the factory defaults, scan the Default Data Format code below. * Default Data Format Show Data Format Scan the barcode below to show current data format settings. Data Format Settings Add a Data Format Step 1.
Page 141: Other Programming Selections
Chart, beginning on page 291. For example, 50 characters is entered as 0050. Note: 9999 indicates all lengths. Step 6. Editor Commands Refer to Data Format Editor Commands (page 124). Scan the symbols that represent the command you want to enter. Step 7.
Page 142: Terminal Id Table
Save Discard Terminal ID Table Terminal Model(s) Terminal ID PC keyboard (HID) Mac Keyboard PC Keyboard (Japanese) Serial (COM driver required) HID POS USB SurePOS Handheld USB SurePOS Tabletop Serial RS232 TTL RS232 True RS485 (IBM-HHBCR 1+2, 46xx) Keyboard PS2 compatibles AT compatibles Data Format Editor Commands When working with the Data Format Editor, a virtual cursor is moved along your...
Page 143 Send a number of characters F2 Include in the output message a number of characters followed by an insert character. Start from the current cursor position and continue for “nn” characters or through the last character in the input message, followed by character “xx.” Syntax = F2nnxx where nn stands for the numeric value (00-99) for the number of characters, and xx stands for the insert character’s hex value for its ASCII code.
Page 144 Send all characters up to a particular character F3 Include in the output message all characters from the input message, starting with the character at the current cursor position and continuing to, but not including, the search character “ss,” followed by an insert character. The cursor is moved forward to the “ss”...
Page 145 42 is the hex value for B The data is output as: 1234567890 Send all but the last characters E9 Include in the output message all but the last “nn” characters, starting from the current cursor position. The cursor is moved forward to one position past the last input message character included.
Page 146 1234567890**ABCDEFGHIJ <CR> Insert symbology name B3 Insert the name of the barcode symbology in the output message, without moving the cursor. Only symbologies with a Honeywell ID are included (see Symbology Charts on page 279). Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 282 for decimal, hex and character codes.
Page 147 B3 is the “Insert symbology name” command F4 is the “Insert a character multiple times” command 20 is the hex value for a space 01 is the number of times the space character is sent B4 is the “Insert barcode length” command F4 is the “Insert a character multiple times”...
Page 148: Move Commands
Move Commands Move the cursor forward a number of characters F5 Move the cursor ahead “nn” characters from current cursor position. Syntax = F5nn where nn is the numeric value (00-99) for the number of characters the cursor should be moved ahead. F5 Example: Move the cursor forward and send the data Move the cursor forward 3 characters, then send the rest of the barcode data from the barcode above.
Page 149: Search Commands
F7 is the “Move the cursor to the beginning” command F2 is the “Send a number of characters” command 06 is the number of characters to send 0D is the hex value for a CR The data is output as: 123456 <CR>...
Page 150 Search backward for a character F9 Search the input message backward for “xx” character from the current cursor position, leaving the cursor pointing to the “xx” character. Syntax = F9xx where xx stands for the search character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 282 for...
Page 151 Search backward for a string B1 Search backward for “s” string from the current cursor position, leaving cursor pointing to “s” string. Syntax = B1nnnnS where nnnn is the string length (up to 9999), and S consists of the ASCII hex value of each character in the match string. For example, B1000454657374 will search backward for the first occurrence of the 4 character string “Test.”...
Page 152: Miscellaneous Commands
Miscellaneous Commands Suppress characters FB Suppress all occurrences of up to 15 different characters, starting at the current cursor position, as the cursor is advanced by other commands. When the FC command is encountered, the suppress function is terminated. The cursor is not moved by the FB command.
Page 153 If the barcode has characters that the host application does not want included, you can use the E4 command to replace those characters with something else. In this example, you will replace the zeros in the barcode above with carriage returns. Command string: E402300DF10D E4 is the “Replace characters”...
Page 154 EC Example: Only output the data if the barcode begins with a number If you want only data from barcodes that begin with a number, you can use EC to check for the number. Command string: ECF10D EC is the “Check for a number” command F1 is the “Send all characters”...
Page 155: Data Formatter
Insert a delay EF Inserts a delay of up to 49,995 milliseconds (in multiples of 5), starting from the current cursor position. Syntax = EFnnnn where nnnn stands for the delay in 5ms increments, up to 9999. This command can only be used with keyboard emulation. Discard Data B8 Discards types of data.
Page 156: Data Format Non-Match Error Tone
requirements generates an error tone and the data in that barcode is not transmitted. If you wish to process this type of barcode without generating an error tone, see Data Format Non-Match Error Tone. • Data Format Required, Drop Prefix/Suffix Scanned data is modified according to your data format.
Page 157: Primary/Alternate Data Formats
Data Format Non-Match Error Tone Off Primary/Alternate Data Formats You can save up to four data formats, and switch between these formats. Your pri- mary data format is saved under 0. Your other three formats are saved under 1, 2, and 3.
Page 158 Single Scan-Data Format 1 Single Scan-Data Format 2 Single Scan-Data Format 3 Granit XP User Guide...
Page 159: Chapter 7 - Symbologies
CHAPTER SYMBOLOGIES This programming section contains the following menu selections. Refer to Chapter 10 for settings and defaults. • All Symbologies • Interleaved 2 of 5 • Aztec Code • Korea Post • China Post (Hong Kong 2 of 5) •...
Page 160: All Symbologies
All Symbologies For best scanner performance, you should only enable the symbologies that you need. Scan All Symbologies Off to disable all symbologies, then enable the sym- bologies you need by scanning the On barcode for each symbology. All Symbologies Off Message Length Description You are able to set the valid reading length of some of the barcode symbologies.
Page 161 Codabar Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the barcode. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Trans- mit. Transmit * Don’t Transmit Codabar Check Character Codabar check characters are created using different “modulos.” You can program the scanner to read only Codabar barcodes with Modulo 16 check characters.
Page 162 Codabar Concatenation Codabar supports symbol concatenation. When you enable concatenation, the scanner looks for a Codabar symbol having a “D” start character, adjacent to a symbol having a “D” stop character. In this case the two messages are concate- nated into one with the “D” characters omitted. A 1 2 3 4 D D 5 6 7 8 A Select Require to prevent the scanner from decoding a single “D”...
Page 163: Code 39
Code 39 < Default All Code 39 Settings > Code 39 On/Off * On If you are reading Code 39 barcodes, Codablock A should remain disabled. If you are enabling Codablock A (see Codablock A on page 181), you should disable Code Code 39 Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the barcode.
Page 164 When Check Character is set to Validate and Transmit, the scanner only reads Code 39 barcodes printed with a check character, and will transmit this character at the end of the scanned data. Default = No Check Character. * No Check Character Validate, but Don’t Transmit Validate and Transmit Code 39 Message Length...
Page 165 Code 32 Pharmaceutical (PARAF) Code 32 Pharmaceutical is a form of the Code 39 symbology used by Italian phar- macies. This symbology is also known as PARAF. Note: Trioptic Code (page 181) must be turned off while scanning Code 32 Pharmaceutical codes.
Page 166: Interleaved 2 Of 5
* Full ASCII Off Code 39 Code Page Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar- code being scanned was created using a code page that is different from the one the host program is expecting.
Page 167 When Check Digit is set to Validate and Transmit, the scanner only reads Inter- leaved 2 of 5 barcodes printed with a check digit, and will transmit this digit at the end of the scanned data. Default = No Check Digit. * No Check Digit Validate, but Don’t Transmit Validate and Transmit...
Page 168: Nec 2 Of 5
NEC 2 of 5 < Default All NEC 2 of 5 Settings > NEC 2 of 5 On/Off * On Check Digit No Check Digit indicates that the scanner reads and transmits barcode data with or without a check digit. When Check Digit is set to Validate, but Don’t Transmit, the unit only reads NEC 2 of 5 barcodes printed with a check digit, but will not transmit the check digit with the scanned data.
Page 169: Code 93
NEC 2 of 5 Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 142) for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 93 <...
Page 170 Code 93 Append This function allows the scanner to append the data from several Code 93 bar- codes together before transmitting them to the host computer. When this function is enabled, the scanner stores those Code 93 barcodes that start with a space (excluding the start and stop symbols), and does not immediately transmit the data.
Page 171: Straight 2 Of 5 Industrial (Three-Bar Start/Stop)
Straight 2 of 5 Industrial (three-bar start/stop) <Default All Straight 2 of 5 Industrial Settings> Straight 2 of 5 Industrial On/Off * Off Straight 2 of 5 Industrial Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 142) for additional information.
Page 172: Straight 2 Of 5 Iata (Two-Bar Start/Stop)
Straight 2 of 5 IATA (two-bar start/stop) <Default All Straight 2 of 5 IATA Settings> Straight 2 of 5 IATA On/Off * Off Straight 2 of 5 IATA Redundancy If you are encountering errors when reading Straight 2 of 5 IATA barcodes, you may want to adjust the redundancy count.
Page 173: Matrix 2 Of 5
Matrix 2 of 5 <Default All Matrix 2 of 5 Settings> Matrix 2 of 5 On/Off * Off Matrix 2 of 5 Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 142) for additional information. Minimum and Maximum lengths = 1-80.
Page 174: Code 11
Code 11 <Default All Code 11 Settings> Code 11 On/Off * Off Check Digits Required This option sets whether 1 or 2 check digits are required with Code 11 barcodes. Default = Two Check Digits. One Check Digit * Two Check Digits Code 11 Message Length Scan the barcodes below to change the message length.
Page 175: Code 128
Code 128 <Default All Code 128 Settings> Code 128 On/Off * On If you are reading Code 128 barcodes, Codablock F should remain disabled. If you are enabling Codablock F (see Codablock F on page 182), you should disable Code 128.
Page 176 the higher the redundancy count, the longer it will take to decode the barcode. To adjust the redundancy, scan the Code 128 Redundancy barcode below, then scan a redundancy count between 0 and 10 on the Programming Chart, beginning on page 291.
Page 177: Gs1-128
Replacements on page 286), and scan the value and the Save barcode from the Programming Chart, beginning on page 291. The data characters should then appear properly. Code 128 Code Page GS1-128 <Default All GS1-128 Settings> GS1-128 On/Off * On GS1-128 Message Length Scan the barcodes below to change the message length.
Page 178: Telepen
Telepen <Default All Telepen Settings> Telepen On/Off * Off Telepen Output Using AIM Telepen Output, the scanner reads symbols with start/stop pattern 1 and decodes them as standard full ASCII (start/stop pattern 1). When Original Telepen Output is selected, the scanner reads symbols with start/stop pattern 1 and decodes them as compressed numeric with optional full ASCII (start/stop pat- tern 2).
Page 179: Upc-A
Maximum Message Length UPC-A <Default All UPC-A Settings> UPC-A On/Off * On Note: To convert UPC-A barcodes to EAN-13, see Convert UPC-A to EAN-13 on page 168. UPC-A Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not.
Page 180 UPC-A Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the begin- ning of the scanned data, but can be programmed so it is not transmitted (Off). Default = On. * On UPC-A Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-A data. Default = Off for both 2 Digit and 5 Digit Addenda.
Page 181: Upc-A/Ean-13 With Extended Coupon Code
* Not Required Addenda Timeout You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for UPC-A Addenda Required.
Page 182: Coupon Gs1 Databar Output
If you scan the Require Concatenation code, the scanner must see and read the coupon code and extended coupon code in a single read to transmit the data. No data is output unless both codes are read. Default = Off. * Off Allow Concatenation Require Concatenation...
Page 183: Upc-E0
UPC-E0 <Default All UPC-E Settings> UPC-E0 On/Off Most U.P.C. barcodes lead with the 0 number system. To read these codes, use the UPC-E0 On selection. If you need to read codes that lead with the 1 number sys- tem, use UPC-E1 (page 167).
Page 184 Addenda Timeout You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for UPC-E0 Addenda Required.
Page 185: Upc-E1
UPC-E0 Leading Zero This feature allows the transmission of a leading zero (0) at the beginning of scanned data. To prevent transmission, scan Off. Default = On. * On UPC-E0 Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-E data. Default = Off for both 2 Digit and 5 Digit Addenda.
Page 186: Ean/Jan-13
* UPC-E1 Off EAN/JAN-13 <Default All EAN/JAN Settings> EAN/JAN-13 On/Off * On Convert UPC-A to EAN-13 When UPC-A Converted to EAN-13 is selected, UPC-A barcodes are converted to 13 digit EAN-13 codes by adding a zero to the front. When Do not Convert UPC-A is selected, UPC-A codes are read as UPC-A.
Page 187 EAN/JAN-13 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On EAN/JAN-13 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data. Default = Off for both 2 Digit and 5 Digit Addenda.
Page 188 EAN-13 Beginning with 290 Addenda Required This setting programs the scanner to require a 5 digit addenda only on EAN-13 barcodes that begin with “290.” The following settings can be programmed: Require 5 Digit Addenda: All EAN-13 barcodes that begin with “290” must have a 5 digit addendum.
Page 189 Require 2 Digit Addenda Require 5 Digit Addenda Require 2 or 5 Digit Addenda EAN-13 Beginning with 414/419 Addenda Required This setting programs the scanner to require any combination of a 2 digit addenda or a 5 digit addenda on EAN-13 barcodes that begin with a “414” or “419.” The fol- lowing settings can be programmed: Require Addenda: All EAN-13 barcodes that begin with a “414”...
Page 190 EAN-13 Beginning with 434/439 Addenda Required This setting programs the scanner to require any combination of a 2 digit addenda or a 5 digit addenda on EAN-13 barcodes that begin with a “434” or “439.” The fol- lowing settings can be programmed: Require Addenda: All EAN-13 barcodes that begin with a “434”...
Page 191 Default = Don’t Require 2 Digit Addenda. * Don’t Require 2 Digit Addenda Require 2 Digit Addenda EAN-13 Beginning with 978 Addenda Required These settings program the scanner to require a 5 digit addenda only on EAN-13 barcodes that begin with “978.” The following settings can be programmed: Require 5 Digit Addenda: All EAN-13 barcodes that begin with “978”...
Page 192 Default = Don’t Require 5 Digit Addenda. * Don’t Require 5 Digit Addenda Require 5 Digit Addenda Addenda Timeout You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for EAN/JAN-13 Addenda Required.
Page 193: Isbn Translate
ISBN Translate When On is scanned, EAN-13 Bookland symbols are translated into their equiva- lent ISBN number format. Default = Off. * Off EAN/JAN-8 <Default All EAN/JAN-8 Settings> EAN/JAN-8 On/Off * On EAN/JAN-8 Check Digit This selection allows you to specify whether or not the check digit should be trans- mitted at the end of the scanned data.
Page 194 EAN/JAN-8 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-8 data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off EAN/JAN-8 Addenda Required When Required is scanned, the scanner will only read EAN/JAN-8 barcodes that...
Page 195: Msi
ting the timeout (from 0-120 milliseconds) by scanning digits from the Programming Chart, beginning on page 291 of this manual, then Save. Default = 500. Note: The Addenda Timeout setting is applied to all addenda and coupon code searches. Addenda Timeout EAN/JAN-8 Addenda Separator When this feature is On, there is a space between the data from the barcode and the data from the addenda.
Page 196 MSI Check Character Different types of check characters are used with MSI barcodes. You can program the scanner to read MSI barcodes with Type 10 check characters. Default = Validate Type 10, but Don’t Transmit. When Check Character is set to Validate Type 10/11 and Transmit, the scanner will only read MSI barcodes printed with the specified type check character(s), and will transmit the character(s) at the end of the scanned data.
Page 197: Gs1 Databar Omnidirectional
MSI Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 142) for additional information. Minimum and Maximum lengths = 4-48. Minimum Default = 4, Maximum Default = 48. Minimum Message Length Maximum Message Length GS1 DataBar Omnidirectional <...
Page 198: Gs1 Databar Limited
GS1 DataBar Limited < Default All GS1 DataBar Limited Settings > GS1 DataBar Limited On/Off * On GS1 DataBar Expanded < Default All GS1 DataBar Expanded Settings > GS1 DataBar Expanded On/Off * On GS1 DataBar Expanded Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 142) for additional information.
Page 199: Trioptic Code
Maximum Message Length Trioptic Code Note: If you are going to scan Code 32 Pharmaceutical codes (page 147), Trioptic Code must be off. Trioptic Code is used for labeling magnetic storage media. * Off Codablock A <Default All Codablock A Settings> Codablock A On/Off * Off If you are reading Code 39 barcodes, Codablock A should remain disabled.
Page 200: Codablock F
Codablock A Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 142) for additional information. Minimum and Maximum lengths = 1-600. Minimum Default = 1, Maximum Default = 600. Minimum Message Length Maximum Message Length Codablock F <Default All Codablock F Settings>...
Page 201: Label Code
Maximum Message Length Label Code The standard Label Code is used in libraries. Default = Off. *Off PDF417 < Default All PDF417 Settings > PDF417 On/Off * On Granit XP User Guide...
Page 202: Macropdf417
PDF417 Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 142) for additional information. Minimum and Maximum lengths = 1-2750. Minimum Default = 1, Maximum Default = 2750. Minimum Message Length Maximum Message Length MacroPDF417 MacroPDF417 is an implementation of PDF417 capable of encoding very large amounts of data into multiple PDF417 barcodes.
Page 203: Gs1 Composite Codes
* Off MicroPDF417 Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 142) for additional information. Minimum and Maximum lengths = 1-366. Minimum Default = 1, Maximum Default = 366. Minimum Message Length Maximum Message Length GS1 Composite Codes Linear codes are combined with a unique 2D composite component to form a new...
Page 204: Gs1 Emulation
UPC/EAN Version Scan the UPC/EAN Version On barcode to decode GS1 Composite symbols that have a U.P.C. or an EAN linear component. (This does not affect GS1 Composite symbols with a GS1-128 or GS1 linear component.) Default = UPC/EAN Version Off. UPC/EAN Version On * UPC/EAN Version Off Note: If you scan coupons that have both UPC and GS1 Databar codes, you may wish to...
Page 205: Tcif Linked Code 39 (Tlc39)
If GS1 Code Expansion Off is scanned, retail code expansion is disabled, and UPC- E expansion is controlled by the UPC-E0 Expand (page 165) setting. If the AIM ID is enabled, the value will be the GS1-128 AIM ID, ]C1 (see Symbology Charts page 279).
Page 206: Qr Code
QR Code < Default All QR Code Settings > QR Code On/Off This selection applies to both QR Code and Micro QR Code. * On QR Code Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 142) for additional information.
Page 207 Swipe: Pull and hold down the trigger and scan all appended QR Codes while keep- ing the trigger pressed. The scanner emits short beeps for each partial QR Code that is scanned and buffered. One long beep is emitted after the last QR Code is scanned and the data is complete.
Page 208: Dotcode
DotCode < Default All DotCode Settings > DotCode On/Off * Off Poor Quality DotCodes This setting improves the scanner’s ability to read damaged or badly printed Dot- Codes. Default = Poor Quality DotCodes Off. Poor Quality DotCodes On * Poor Quality DotCodes Off DotCode Message Length Scan the barcodes below to change the message length.
Page 209: Digimarc Barcode
Digimarc Barcode™ Digimarc Decoder Attempts Set the number of attempts by scanning the barcode below, then setting the num- ber of attempts (0-10) by scanning digits from the Programming Chart beginning on page 291 of this manual, the Save. Minimum to Maximum attempts = 0-10. Default = 3.
Page 210: Data Matrix
* Uses Digimarc Decoder then Both Decoders Uses ID Decoder then Alternates Decoders Uses Digimarc Decoder then Alternates Decoders Data Matrix < Default All Data Matrix Settings > Data Matrix On/Off * On Direct Part Marking Decoding If you are having trouble reading Direct Part Marking (DPM) barcodes, scan Dot- peen DPM Decoding for Dotpeen codes or scan Reflective (Etched) DPM Decod- ing for reflective (etched) codes Default = Disable DPM Decoding.
Page 211 * Disable DPM Decoding Reflective (Etched) DPM Decoding Data Matrix Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 142) for additional information. Minimum and Maximum lengths = 1-3116. Minimum Default = 1, Maximum Default = 3116. Minimum Message Length Maximum Message Length Data Matrix Code Page...
Page 212: Maxicode
MaxiCode < Default All MaxiCode Settings > MaxiCode On/Off * Off MaxiCode Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 142) for additional information. Minimum and Maximum lengths = 1-150. Minimum Default = 1, Maximum Default = 150. Minimum Message Length Maximum Message Length Granit XP User Guide...
Page 213: Aztec Code
Aztec Code < Default All Aztec Code Settings > Aztec Code On/Off * On Aztec Code Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 142) for additional information. Minimum and Maximum lengths = 1-3832.
Page 214: Chinese Sensible (Han Xin) Code
Aztec Code Page Aztec Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar- code being scanned was created using a code page that is different from the one the host program is expecting.
Page 215: Postal Codes - 2D
Han Xin Code Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 142) for additional information. Minimum and Maximum lengths = 1-7833. Minimum Default = 1, Maximum Default = 7833. Minimum Message Length Maximum Message Length Postal Codes - 2D The following lists the possible 2D postal codes, and 2D postal code combinations...
Page 216 Japanese Post On KIX Post On Planet Code On Also see Planet Code Check Digit, page 200. Postal-4i On Postnet On Postnet On Also see Postnet Check Digit, page 201. Postnet with B and B’ Fields On InfoMail On Combination 2D Postal Codes: InfoMail and British Post On Intelligent Mail Barcode and...
Page 217 Postnet and Postal-4i On Postnet and Intelligent Mail Barcode On Postal-4i and Intelligent Mail Barcode On Postal-4i and Postnet with B and B’ Fields On Planet Code and Postnet On Planet Code and Postnet with B and B’ Fields On Planet Code and Postal-4i On Planet Code and...
Page 218: Planet Code Check Digit
Planet Code, Postal-4i, and Intelligent Mail Barcode On Postnet, Postal-4i, and Intelligent Mail Barcode On Planet Code, Postal-4i, and Postnet with B and B’ Fields On Planet Code, Intelligent Mail Barcode, and Postnet with B and B’ Fields On Postal-4i, Intelligent Mail Barcode, and Postnet with B and B’...
Page 219: Postnet Check Digit
* Don’t Transmit Check Digit Postnet Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of Postnet data. Default = Don’t Transmit. Transmit Check Digit * Don’t Transmit Check Digit Australian Post Interpretation This option controls what interpretation is applied to customer fields in Australian 4-State symbols.
Page 220: Postal Codes - Linear
Combination C and N Tables Postal Codes - Linear The following lists linear postal codes. Any combination of linear postal code selec- tions can be active at a time. China Post (Hong Kong 2 of 5) <Default All China Post (Hong Kong 2 of 5) Settings> China Post (Hong Kong 2 of 5) On/Off * Off China Post (Hong Kong 2 of 5) Message Length...
Page 221: Korea Post
Korea Post <Default All Korea Post Settings> Korea Post * Off Korea Post Message Length Scan the barcodes below to change the message length. Refer to Message Length Description (page 142) for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 48. Minimum Message Length Maximum Message Length Korea Post Check Digit...
Page 222 Granit XP User Guide...
Page 223: Chapter 8 - Imaging Commands
CHAPTER IMAGING COMMANDS The scanner is like a digital camera in the way it captures, manipulates, and trans- fers images. The following commands allow you to alter the way the scanner per- forms these functions. Single-Use Basis Imaging Commands with their modifiers send instructions to the scanner on a sin- gle-use basis, and take effect for a single image capture.
Page 224: Image Snap - Imgsnp
The modifiers for each of these commands follow the command description. Note: The images included with each command description are examples only. The results you achieve may be different from those included in this manual. The quality of the output you receive will vary depending on lighting, quality of the initial image/object being captured, and distance of the scanner from the image/object.
Page 225 T - Wait for Trigger Waits for a hardware trigger press before taking the image. This is only available when using Photo Style (1P). Takes image immediately (default) Waits for a trigger press, then takes the image L - LED State Determines if the LEDs should be on or off, and when.
Page 226 G - Gain Gain is used in Manual Style only (2P). Like a volume control, the gain modifier boosts the signal and multiplies the pixel value. As you increase the gain, the noise in an image is also amplified. No gain (default) Medium gain Heavy gain Maximum gain...
Page 227: Image Ship - Imgshp
U - Update Tries This sets the maximum number of frames the scanner should take to reach the Delta for Acceptance. Update Tries is only available when using Photo Style (1P). (Default = 6) Range: 0 - 10 % - Target Set Point Percentage Sets the target point for the light and dark values in the captured image.
Page 228: Imgshp Modifiers
IMGSHP Modifiers A - Infinity Filter Enhances pictures taken from very long distances (greater than 10 feet or 3m). The Infinity Filter should not be used with IMGSNP Modifiers (page 206). Infinity filter off (default) Infinity filter on Example: Infinity Filter off (0A) Infinity Filter on (1A) from approximately 12 feet from approximately 12 feet (3.66m)
Page 229 E - Edge Sharpen An edge sharpen filter cleans up the edges of an image, making it look cleaner and sharper. While edge sharpening does make the image look cleaner, it also removes some fine detail from the original image. The strength of the edge sharpen filter can be entered from 1 to 24.
Page 230 H - Histogram Stretch Increases the contrast of the transmitted image. Not available with some image formats. No stretch (default) Histogram stretch Example: Histogram Stretch at 0H: Histogram Stretch at 1H: I - Invert Image Invert image is used to rotate the image around the X or Y axis. Invert around the X axis (flips picture upside down) Invert around the Y axis (flips picture left to right) Example:...
Page 231 IF- Noise Reduction Used to reduce the salt and pepper noise in an image. No salt and pepper noise reduction (default) Salt and pepper noise reduction Example: Noise Reduction Off (0if): Noise Reduction On (1if): IR - Image Rotate Image as snapped (rightside up) (default) Rotate image 90 degrees to the right Rotate image 180 degrees (upside down) Rotate image 90 degrees to the left...
Page 232 J - JPEG Image Quality Sets the desired quality when the JPEG image format is selected. Higher numbers result in higher quality, but larger files. Smaller numbers result in greater amounts of lossy compression, faster transmission times, lower quality, but smaller files. (Default = 50) Image is compressed as much as possible while preserving quality factor of n (n = 0 - 100)
Page 233 The bottom edge of the shipped image corresponds to row n - 1 of the image in memory. Range: 000 - 639. (Default = all rows) Example: Uncropped Image: Image Crop set to Image Crop set to 300R: 300L: Image Crop set to 200B: Image Crop set to 200T: Alternately, specify the number of pixels to cut from the outside margin of the image;...
Page 234 The smaller number of pixels shipped, the smaller the image, however, after a cer- tain point the image becomes unusable. ship every pixel (default) ship every 2nd pixel, both horizontally and vertically ship every 3rd pixel, both horizontally and vertically Pixel Ship Pixel Ship Example:...
Page 235: Image Size Compatibility
V - Blur Image Smooths transitions by averaging the pixels next to the hard edges of defined lines and shaded areas in an image. Don’t blur (default) Blur Example: Blur Image Off (0V): Blur Image On (1V): W - Histogram Ship A histogram gives a quick picture of the tonal range of an image, or key type.
Page 236: Intelligent Signature Capture - Imgbox
* Native Resolution Intelligent Signature Capture - IMGBOX IMGBOX allows you to configure the size and location of a signature capture area relative to its proximity to a barcode. This allows you to tailor a signature capture area to a specific form. In order to use IMGBOX, you need a set form where the sig- nature box location is in a known location relative to a barcode.
Page 237: Imgbox Modifiers
To see this example, align the aimer with the signature area (not with the barcode), then press the trigger. Send the following IMGBOX command string after the trigger press: Example: IMGBOX245w37h55y. Note: Case is not important in the command string. It is used here only for clarity. The following image is captured: The IMGBOX commands have many different modifiers that can be used to change the size and appearance of the signature image output by the scanner.
Page 238 B - Output Image Height This option is used to size the image vertically. If using this option, set the resolu- tion (R) to zero. Example: Image Height set to 50B: Image Height set to 100B: D - Pixel Depth This indicates the number of bits per pixel in the transmitted image, which defines whether it will be grayscale or black and white.
Page 239 H - Height of Signature Capture Area The height of the signature capture area must be measured in inches divided by .01. In the example, the height of the area to be captured is 3/8 inch, resulting in a value of H = .375/0.01 = 37.5. Example: IMGBOX245w37h55y.
Page 240 decimal point between the first and second digit. For example, use 2500 to specify a resolution of 2.5. Set to zero when using the A and B modifiers (see A - Output Image Width B - Output Image Height on page 220). Example: Resolution set to 0R: Resolution set to 1000R:...
Page 241: Rf Default Imaging Device
Y - Vertical Barcode Offset The vertical barcode offset allows you to offset the vertical center of the signature capture area. Negative numbers indicate that the signature capture is above the barcode, and positive numbers indicate that the area is below the barcode. Mea- surements are in multiples of the minimum bar width Example: Vertical Offset set to -7Y:...
Page 242 Granit XP User Guide...
Page 243: Chapter 9 - Utilities
CHAPTER UTILITIES To Add a Test Code I.D. Prefix to All Symbologies This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Charts, beginning on page 279 for the single char- acter code that identifies each symbology.) This action first clears all current pre- fixes, then programs a Code I.D.
Page 244: Totalfreedom
* Off TotalFreedom TotalFreedom is an open system architecture that makes it possible for you create applications that reside on your scanner. Decoding apps and Data Formatting apps can be created using TotalFreedom. For further information about TotalFree- dom, go to our website at www.honeywellaidc.com. Application Plug-Ins (Apps) Any apps that you are using can be turned off or on by scanning the following bar- codes.
Page 245: Ezconfig For Scanning Introduction
Configure with EZConfig for Scanning Use the EZConfig for Scanning tool to configure your scanner online: 1. Access the Honeywell Technical Support Downloads Portal at https:// hsmftp.honeywell.com. 2. Go to Software > Barcode Scanners > Software > Tools and Utilities >...
Page 246: Reset The Factory Defaults
Reset the Factory Defaults Caution: This selection erases all your settings and resets the scanner to the original factory defaults. It also disables all plugins. If you aren’t sure what programming options are in your scanner, or you’ve changed some options and want to restore the scanner to factory default settings, first scan the Remove Custom Defaults barcode, then scan Activate Defaults.
Page 247: Chapter 10 - Serial Programming Commands
CHAPTER SERIAL PROGRAMMING COMMANDS The serial programming commands can be used in place of the programming bar- codes. Both the serial commands and the programming barcodes will program the scanner. For complete descriptions and examples of each serial programming command, refer to the corresponding programming barcode in this manual. The device must be set to an RS232 interface (see page 14).
Page 248: Query Commands
scanner. This setting is changed by using the BT_NAM command, which accepts alphanumeric values. If the name is not known, a wild- card (*) can be used :* Note: Since the base stores all work group settings and transfers to them to scanner once they are linked, changes are typically done to the base and not to the scanner.
Page 249 SubTag Field Usage When a query is used in place of a SubTag field, the query applies only to the sub- set of commands available that match the Tag field. In this case, the Data field should not be used because it is ignored by the device. Data Field Usage When a query is used in place of the Data field, the query applies only to the spe- cific command identified by the Tag and SubTag fields.
Page 250: Trigger Commands
This response indicates that Codabar Coding Enable (CBRENA) has a range of val- ues from 0 to 1 (off and on). Example: What is the default value for Codabar Coding Enable? Enter: cbrena^. Response: CBRENA1[ACK] This response indicates that the default setting for Codabar Coding Enable (CBRENA) is 1, or on.
Page 251: Reset The Custom Defaults
The scanner scans until a barcode has been read, until the deactivate command is sent, or until the serial time-out has been reached (see Read Time-Out on page 87 for a description, and the serial command on page 244). Reset the Custom Defaults If you want the custom default settings restored to your scanner, scan the Activate Custom Defaults barcode below.
Page 252: Menu Commands
ACK/NAK Mode On USBACK1 *ACK/NAK Mode Off USBACK0 Plug and Play Codes Verifone Ruby Terminal PAPRBY Gilbarco Terminal PAPGLB Honeywell Bioptic Aux Port PAPBIO Datalogic Magellan Aux Port PAPMAG Wincor Nixdorf Terminal PAPWNX Wincor Nixdorf Beetle PAPBTL Wincor Nixdorf RS232 Mode A...
Page 253 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Program Keyboard *U.S.A. KBDCTY0 Country Albania KBDCTY35 Azeri (Cyrillic) KBDCTY81 Azeri (Latin) KBDCTY80 Belarus KBDCTY82 Belgium KBDCTY1 Bosnia KBDCTY33 Brazil KBDCTY16 Brazil (MS) KBDCTY59 Bulgaria (Cyrillic) KBDCTY52 Bulgaria (Latin) KBDCTY53 Canada (French legacy)
Page 254 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Hungary KBDCTY19 Iceland KBDCTY75 Irish KBDCTY73 Italian (142) KBDCTY56 Italy KBDCTY5 Japan ASCII KBDCTY28 Kazakh KBDCTY78 Kyrgyz (Cyrillic) KBDCTY79 Latin America KBDCTY14 Latvia KBDCTY42 Latvia (QWERTY) KBDCTY43 Lithuania KBDCTY44 Lithuania (IBM)
Page 255 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Tatar KBDCTY85 Turkey F KBDCTY27 Turkey Q KBDCTY24 Ukrainian KBDCTY76 United Kingdom KBDCTY7 United Stated (Dvorak right) KBDCTY89 United States (Dvorak left) KBDCTY88 United States (Dvorak) KBDCTY87 United States (International) KBDCTY30 Uzbek (Cyrillic)
Page 256 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Keyboard Modifiers *Control + X Off KBDCAS0 DOS Mode Control + X KBDCAS1 Windows Mode Control + X KBDCAS2 Windows Mode Prefix/Suffix Off KBDCAS3 DOS Mode Control + X Mode On KBDCAS4 with Windows Mode Prefix/Suffix Supports ALT 3 Digit HEX Mode...
Page 257 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry RS232 Handshaking *RTS/CTS Off 232CTS0 Flow Control, No Timeout 232CTS1 Two-Direction Flow Control 232CTS2 Flow Control with Timeout 232CTS3 RS232 Timeout (1-5100 232DEL#### milliseconds) *XON/XOFF Off 232XON0 XON/XOFF On 232XON1 *ACK/NAK Off...
Page 258 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Beeper Pitch - Base Error *Low/Razz (250 Hz) (min 200 Hz) BASFQ2250 Medium (3250 Hz) BASFQ23250 High (4200 Hz) (max 9000 Hz) BASFQ24200 Number of Beeps - Base Error *1 (Range 1 - 9) BASERR# Scanner Report...
Page 259 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Batch Mode Quantity *Off BATQTY0 BATQTY1 Quantity Codes BATNUM0 BATNUM1 BATNUM2 BATNUM3 BATNUM4 BATNUM5 BATNUM6 BATNUM7 BATNUM8 BATNUM9 Batch Mode Output Order *FIFO BATLIF0 LIFO BATLIF1 Total Records Total Records BATNRC Delete Last Code...
Page 260 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Application Work Group *Group 0 GRPSEL0 Selections Group 1 GRPSEL1 Group 2 GRPSEL2 Group 3 GRPSEL3 Group 4 GRPSEL4 Group 5 GRPSEL5 Group 6 GRPSEL6 Reset the Factory Defaults: All Factory Default Settings: PAPDFT&...
Page 261 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Beep on BEL Character Beep on BEL On BELBEP1 *Beep on BEL Off BELBEP0 Trigger Click BEPTRG1 *Off BEPTRG0 Beeper - Good Read BEPBEP0 BEPBEP1 Beeper Volume - Good Read BEPLVL0 *Low BEPLVL1...
Page 262 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry 3 Quick Triggers TRGTPC3 4 Quick Triggers TRGTPC4 Trigger Timing Trigger Timing (Range 50 - 2000) TRGTTI#### *400 Trigger Toggle Timeout Trigger Toggle Timeout (Range 0 - TRGTGT## 65) *5 Serial Trigger Mode...
Page 263 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry User-Specified Range 0 - 30,000 ms DLYRRD##### 2D Reread Delay *2D Reread Delay Off DLY2RR0 Short (1000ms) DLY2RR1000 Medium (2000ms) DLY2RR2000 Long (3000ms) DLY2RR3000 Extra Long (4000ms) DLY2RR4000 Character Activation Mode *Off...
Page 264 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Preferred Symbology PRFENA1 *Off PRFENA0 High Priority Symbology PRFCOD## Low Priority Symbology PRFBLK## Preferred Symbology Timeout PRFPTO#### (Range 100-3000) *500 Preferred Symbology Default PRFDFT Output Sequence Editor Enter Output Sequence SEQBLK Add Prefix to Complete Output...
Page 265 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry No Read SHWNRD1 *Off SHWNRD0 Video Reverse Video Reverse Only VIDREV1 Video Reverse and Standard VIDREV2 Barcodes *Video Reverse Off VIDREV0 Working Orientation *Upright ROTATN0 Vertical, Bottom to Top (Rotate ROTATN1 CCW 90°) Upside Down...
Page 266 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Out-of-Range Delay Out-of-Range Delay (Range 0- BT_ORY#### 3000) *0 Prefix/Suffix Selections Add CR Suffix to All Symbologies VSUFCR Prefix Add Prefix PREBK2## Clear One Prefix PRECL2 Clear All Prefixes PRECA2 Suffix Add Suffix...
Page 267 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Primary/Alternate Data Formats Primary Data Format ALTFNM0 Data Format 1 ALTFNM1 Data Format 2 ALTFNM2 Data Format 3 ALTFNM3 Single Scan Data Format Change Single Scan-Primary VSAF_0 Data Format Single Scan-Data Format 1 VSAF_1...
Page 268 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Code 39 Append *Off C39APP0 C39APP1 Code 32 Pharmaceutical (PARAF) *Off C39B320 C39B321 Code 39 Full ASCII *Off C39ASC0 C39ASC1 Code 39 Code Page C39DCP Interleaved 2 of 5 Default All Interleaved I25DFT 2 of 5 Settings...
Page 269 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Straight 2 of 5 Industrial Default All Straight 2 of 5 R25DFT Industrial Settings *Off R25ENA0 R25ENA1 Straight 2 of 5 Industrial Message Minimum (1 - 48) *4 R25MIN## Length Maximum (1 - 48) *48...
Page 270 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry GS1-128 Default All GS1-128 Settings GS1DFT GS1ENA1 GS1ENA0 GS1-128 Message Length Minimum (1 - 80) *1 GS1MIN## Maximum (0 - 80) *80 GS1MAX## Telepen Default All Telepen TELDFT Settings *Off...
Page 271 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry UPC-E0 Default All UPC-E UPEDFT Settings UPEEN00 UPEEN01 UPC-E0 Expand *Off UPEEXP0 UPEEXP1 UPC-E0 Addenda Required Required UPEARQ1 *Not Required UPEARQ0 Addenda Timeout Range (0 - 120) *500 DLYADD##### UPC-E0 Addenda Separator UPEADS1...
Page 272 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry EAN-13 Beginning with 378/379 *Don’t Require Addenda ARQ3780 Addenda Required Require 2 Digit Addenda ARQ3781 Require 5 Digit Addenda ARQ3782 Require 2 or 5 Digit Addenda ARQ3783 EAN-13 Beginning with 414/419 *Don’t Require Addenda ARQ4140...
Page 273 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Default All MSI Settings MSIDFT *Off MSIENA0 MSIENA1 MSI Check Character *Validate Type 10, but Don’t MSICHK0 Transmit Validate Type 10 and MSICHK1 Transmit Validate 2 Type 10 Chars, but MSICHK2 Don’t Transmit Validate 2 Type 10 Chars and...
Page 274 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Codablock F Default All Codablock F Settings CBFDFT *Off CBFENA0 CBFENA1 Codablock F Msg. Length Minimum (1 - 2048) *1 CBFMIN#### Maximum (1 - 2048) *2048 CBFMAX#### Label Code LBLENA1 *Off...
Page 275 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry QR Code Append *One Scan QRCAPP1 Swipe QRCAPP2 Point & Shoot QRCAPP3 QRCAPP0 QR Code Page QR Code Page (*3) QRCDCP## DotCode Default All DotCode Settings DOTDFT DOTENA1 *Off DOTENA0...
Page 276 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Aztec Code Default All Aztec Code Settings AZTDFT AZTENA1 AZTENA0 Aztec Code Msg. Length Minimum (1-3832) *1 AZTMIN#### Maximum (1-3832) *3832 AZTMAX#### Aztec Append AZTAPP1 AZTAPP0 Aztec Code Page Aztec Code Page (*51) AZTDCP## Chinese Sensible (Han Xin) Code...
Page 277 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Planet and Postal-4i On POSTAL13 Planet and Intelligent Mail POSTAL15 Barcode On Planet, Postnet, and Postal-4i On POSTAL21 Planet, Postnet, and Intelligent POSTAL22 Mail Barcode On Planet, Postal-4i, and Intelligent POSTAL23 Mail Barcode On Postnet, Postal-4i, and Intelligent...
Page 278 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Korea Post Msg. Length Minimum (2 - 80) *4 KPCMIN## Maximum (2 - 80) *48 KPCMAX## Korea Post Check Digit Transmit Check Digit KPCCHK1 *Don’t Transmit Check Digit KPCCHK0 Imaging Default Commands Image Snap...
Page 279 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry File Format - TIFF binary group 4, IMGFMT2 compressed File Format - TIFF grayscale IMGFMT3 File Format - Uncompressed IMGFMT4 binary File Format - Uncompressed IMGFMT5 grayscale File Format - BMP IMGFMT8 *Histogram Stretch Off...
Page 280 Serial Command Setting Selection # Indicates a numeric Page * Indicates default entry Ship Histogram IMGHST1 Image Size Compatibility Force VGA Resolution IMGVGA1 *Native Resolution IMGVGA0 Intelligent Signature Capture Optimize On DECBND1 *Optimize Off DECBND0 Utilities Add Code I.D. Prefix to All Symbologies (Temporary) PRECA2,BK2995C80! Show Software Revision REVINF...
Page 281: Chapter 11 - Product Specifications
CHAPTER PRODUCT SPECIFICATIONS Granit XP SR and Granit XP XR 1990i Corded Scanner Product Specifications Parameter Specification Mechanical Height 7.5 inches (192mm) Length 3.9 inches (100mm) Width 2.9 inches (76mm) Weight 11.2 ounces (320g) Electrical Voltage Requirements 4.4 to 5.5 VDC at input connector Current Draw ScanningStandby 500mA @ 5VDC, 2.5W...
Page 282 Parameter (Continued) Specification ESD Tolerance Up to ±20kV direct air Up to 8 kV indirect coupling plane Image Image Size 1280 x 800 pixels Scan Performance Skew Angle +65° Pitch Angle 1D barcode 1D code: +65° 2D barcode 2D code: +45° Motion Tolerance Up to 4.5 m/s (157 in/s) for 13 mil UPC at optimal focus...
Page 283 Parameter (Continued) Specification Radio Frequency 2.4 to 2.5 GHz (ISM Band) Frequency Hopping Bluetooth v 4.2 Range 33 ft. (10 m) typical Environmental Temperature Ranges: Operating -4 F to +122 F (-20 C to 50 C) Storage with battery* -4 F to +95 F (-20 C to 35 C) for storage up to 90 days -4 F to +68 F (-20 C to 20 C) for storage up to 365 days...
Page 284: Ccb22-100Bt-03N/Cob22 Charge Base Product Specifications
CCB22-100BT-03N/COB22 Charge Base Product Specifications Parameter Specification Mechanical Height 2.3 inches (60 mm) Length 9.6 inches (245 mm) Width 4.0 inches (102 mm) Weight CCB22 10.4 oz (295g) COB22 10.2 oz (290g) Electrical Voltage: 4.0 to 5.5 VDC Current Draw: Host Terminal Port 500mA Aux Power Port...
Page 285: Depth Of Field Charts
Depth of Field Charts Granit XP SR Performance Focus Typical Spec Guaranteed Spec 3 mil Code 39 1.53 4.09 2.55 1.92 3.58 1.65 5 mil Code 39 0.78 8.66 7.87 1.02 7.75 6.73 10mil Code 39 19.29 19.29 0.39 17.75 17.36 13 mil UPC 19.84...
Page 286: Granit Xp Xr Performance
164.96 Standard Connector Pinouts Note: The following pin assignments are not compatible with some Honeywell legacy products. Use of a cable with improper pin assignments may lead to damage to the unit. Use of any cables not provided by the manufacturer may result in damage not covered by your warranty.
Page 287: Keyboard Wedge
Keyboard Wedge 10 Pin RJ41 Modular Plug - connects to the base Cable shield Cable select Supply ground Terminal data Terminal clock Keyboard clock +5V power Keyboard data Serial Output 10 Pin RJ41 Modular Plug - connects to the base Cable shield Cable select Supply ground...
Page 288: Usb
Cable shield Cable select Supply ground Transmit data Receive data - serial data to scanner +5V power Transmit Enable 10 Pin Modular Plug - connects to the base Cable shield Cable select Supply ground +5V power Data + 10 Data - Granit XP User Guide...
Page 289: Required Safety Labels
Required Safety Labels Scanner Laser Label location Part Number, Serial Number and Compliance label location Revision Information location Granit XP User Guide...
Page 290: Ccb22-100Bt-03N-Bf Base
CCB22-100BT-03N-BF Base Granit XP User Guide...
Page 291: Chapter 12 - Maintenance And Troubleshooting
CHAPTER MAINTENANCE AND TROUBLESHOOTING Repairs Repairs and/or upgrades are not to be performed on this product. These services are to be performed only by an authorized service center (see Customer Support page xv). Maintenance Your device provides reliable and efficient operation with a minimum of care. Although specific maintenance is not required, the following sections describe periodic checks to ensure dependable operation.
Page 292: Clean The Window
(DRH) for the healthcare and general- purpose markets. Please refer to the Honeywell Safety and Productivity Solutions website for specific details on how to clean scanners with disinfectant-ready housings. Helpful information on the care of these specialty products can be found in the following articles: •...
Page 293: Replace An Interface Cable
Replace an Interface Cable 1. Turn off the power to the host system. 2. Disconnect the scanner’s cable from the terminal or computer. 3. Locate the small screw at the bottom of the locking plate. 4. Loosen the screw. 5. Loosen the locking plate and slide it over the base of the cable connector to remove the cable from the device.
Page 294: Troubleshoot A Cordless System
• The cable is connected properly. • The host system power is on (if external power isn’t used). • The trigger works. Is the scanner having trouble reading your symbols? If the scanner isn’t reading symbols well, check that the symbols: •...
Page 295: Troubleshoot A Cordless Scanner
• Charge mode is turned on. (See "Beeper and LED Sequences and Meaning" on page • The battery is not bad or deeply discharged. In some cases, the scanner’s battery may trickle charge to bring it into an acceptable level and then transition to a normal charge cycle.
Page 296 Granit XP User Guide...
Page 297: Chapter A - Reference Charts
Refer to Data Edit beginning on page 115 and Data Format beginning on page 121 for information about using Code ID and AIM ID. Linear Symbologies Honeywell Possible modifiers Linear Symbology All Symbologies Codabar Code 11 Code 128 0, 1, 2, 4 Code 32 Pharmaceutical (PARAF) <...
Page 298 0, 1, 2, 3, 8, 9, A, B, C UPC-A UPC-A with Add-On UPC-A with Extended Coupon Code UPC-E UPC-E with Add-On UPC-E1 Add Honeywell Code ID 5C80 Add AIM Code ID 5C81 Add Backslash 5C5C Batch mode quantity Granit XP User Guide...
Page 299: 2D Symbologies
2D Symbologies Honeywell Possible modifiers 2D Symbology All Symbologies Aztec Code 0-9, A-C Chinese Sensible Code (Han Xin Code) Codablock A 0, 1, 4, 5, 6 Codablock F 0, 1, 4, 5, 6 Code 49 0, 1, 2, 4 Data Matrix...
Page 300: Ascii Conversion Chart (Code
ASCII Conversion Chart (Code Page 1252) In keyboard applications, ASCII Control Characters can be represented in 3 differ- ent ways, as shown below. The CTRL+X function is OS and application dependent. The following table lists some commonly used Microsoft functionality. This table applies to U.S.
Page 301: Lower Ascii Reference Table
Lower ASCII Reference Table Note: Windows Code page 1252 and lower ASCII use the same characters. Printable Characters Character Character DEC Character <SPACE> " & < > ⌂ Extended ASCII Characters CP 1252 ASCII Alternate Extended PS2 Scan Code ↑ €...
Page 302 Extended ASCII Characters (Continued) CP 1252 ASCII Alternate Extended PS2 Scan Code Œ î Reserved ì Reserved Ž Ä Numeric Keypad Enter 0x1C Å Numeric Keypad / 0x35 É 0x3B ‘ æ 0x3C ’ Æ 0x3D “ ô 0x3E ” ö...
Page 303 Extended ASCII Characters (Continued) CP 1252 ASCII Alternate Extended PS2 Scan Code Â ┬ Ã ├ Ä ─ Å í Æ ╞ Ç ╟ È ╚ É ╔ Ê ╩ Ë ╦ Ì ╠ Í ═ Î ╬ Ï ╧ Ð...
Page 304: Iso 2022/Iso 646 Character Replacements
(standard ASCII) Automatic National Character ISO/IEC 2022 2 (default) Replacement Binary Code page Default “Automatic National Character replacement” will select the below Honeywell Code Page options for Code128, Code 39 and Code 93. United States ISO/IEC 646-06 Canada ISO /IEC 646-121...
Page 305 à â ç ê î ô é ù è û à â ç ê É ô é ù è û ‾ ¥ ‾ ¥ £ ˜ £ à ° ç § µ é ù è ¨ § Ä Ö Ü ä...
Page 306: Keyboard Key References
Keyboard Key References 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 4B 50 55 5A 5F 64 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 4C 51 56 5B 60 65 1F 20 21 22 23 24 25 26 27 28 29...
Page 307: Sample Symbols
SAMPLE SYMBOLS UPC-A Interleaved 2 of 5 01234567890 0 123456 7890 EAN-13 9 780330 290951 Code 128 Code 39 Code 128 BC321 Codabar A13579B Code 93 Straight 2 of 5 Industrial 123456 123456-9$ Matrix 2 of 5 6543210 RSS-14 PDF417 Car Registration (01) 00123456789012 Code 49...
Page 308 SAMPLE SYMBOLS (CONTINUED) Postnet Data Matrix Zip Code Test Symbol QR Code Numbers MaxiCode Micro PDF417 Test Message Test Message DotCode 12345 Granit XP User Guide...
Page 309 PROGRAMMING CHART Granit XP User Guide...
Page 310 PROGRAMMING CHART (CONTINUED) Save Discard Reset Note: If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or digits, and Save again. Granit XP User Guide...
Page 312 Honeywell 9680 Old Bailes Road Fort Mill, SC 29707 www.honeywellaidc.com ™ 199x-EN-UG-01 Rev A 6/20...

This manual is also suitable for:

Granit xp 1990isr Granit xp 1990ixr Granit xp 1991isr Granit xp 1991ixr

Honeywell Granit XP 199 i Series User Manual

Chapter 1 - Get Started

Chapter 2 - Program the Interface

Chapter 3 - Cordless System Operation

Chapter 4 - Input/Output Settings

Chapter 5 - Data Edit

Chapter 6 - Data Format

Chapter 7 - Symbologies

Chapter 8 - Imaging Commands

Quick Links

Related Manuals for Honeywell Granit XP 199 i Series

Summary of Contents for Honeywell Granit XP 199 i Series