HIKVISION D0T Series User Manual
Turret & dome camera
Hide thumbs
Also See for D0T Series:
- User manual (14 pages) ,
- User manual (17 pages) ,
- User manual (11 pages)
Advertisement
D0T Series Turret & Dome Camera
User Manual
Thank you for purchasing our product. If there are any
questions, or requests, do not hesitate to contact the
dealer.
This manual applies to the models below:
Type I Camera
Type II Camera
Type III Camera
Type IV Camera
Type V Camera
Type VI Camera
This manual may contain several technical mistakes or
printing errors, and the content is subject to change
without notice. The updates will be added to the new
version of this manual. We will readily improve or
update the products or procedures described in the
manual.
Type
User Manual
Model
DS-2CE56D0T-IRM(F)
DS-2CE56D0T-IR(F)
DS-2CE56D0T-IRP(F)
DS-2CE56D0T-IT1/3(F)
DS-2CE76D0T-ITPFS
DS-2CE76D0T-ITMFS
DS-2CE56D0T-IRMM(F)
0300001090529
Advertisement
Table of Contents
Related Manuals for HIKVISION D0T Series
Summary of Contents for HIKVISION D0T Series
- Page 1 D0T Series Turret & Dome Camera User Manual User Manual Thank you for purchasing our product. If there are any questions, or requests, do not hesitate to contact the dealer. This manual applies to the models below: Type Model Type I Camera...
-
Page 2: Regulatory Information
Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. - Page 3 Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions”. Warnings: Serious injury or death may occur if any of the warnings are neglected.
-
Page 4: Product Features
Keep the camera away from liquid while in use for non-water-proof device. While in delivery, the camera shall be packed in its original packing, or packing of the same texture. Mark Description Table 0-1 Mark Description Mark Description DC Voltage 1 Introduction 1.1 Product Features... - Page 5 Main Body Enclosure Trim Ring Switch Button Mounting Base Power Cord D C1 2V Video Cable Figure 1-4 Overview of Type II Camera (with F) Note: Press and hold the switch button for 5 seconds to switch the video output. Four kinds of video outputs are available: TVI, AHD, CVI, and CVBS.
- Page 6 1.2.5 Overview of Type V Camera Mounting Base Clip Plate Enclosure Main Body Switch Button Power Cord DC 12 V Video Cable Figure 1-8 Overview of Type V Camera Note: Press and hold the switch button for 5 seconds to switch the video output.
-
Page 7: Installation
2 Installation Before you start Make sure that the device in the package is in good condition and all the assembly parts are included. Make sure that all the related equipment is power-off during the installation. Check the specification of the products for the ... - Page 8 4. Route the cables through the cable hole, or the side opening. 5. Secure the camera on the mounting base. Pull out the clip plate, and then to combine the camera with the mounting base. Push the clip plate in, and secure the camera by tightening the screw.
- Page 9 For cement wall/ceiling, expansion bolts are required to fix the camera. For wooden wall/ceiling, self-tapping screws are required. 4. Route the cables through the cable hole, or the side opening. 5. Install the camera back to the mounting base and secure them with the trim ring.
- Page 10 Note: The supplied screw package contains self-tapping screws, and expansion bolts. 5. Route the cables through the cable hole, or the side opening. 6. Install the camera back to the mounting base and secure it. Figure 2-10 Install the Camera Back 7.
- Page 11 Pan Position [0° to 350°] Tilt Position [0°to70°] Rotation Position [0° to 350°] Figure 2-14 3-Aixs Adjustment 7. Install the black liner and the bubble back. Figure 2-15 Install the Black Liner and the Bubble...
-
Page 12: Menu Description
3 Menu Description Please follow the steps below to call the menu. Note: The actual display may vary with your camera model. Steps: 1. Connect the camera with the TVI DVR, and the monitor, shown as the figure 3-1. TVI DVR Camera Monitor Figure 3-1 Connection... -
Page 13: Video Format
5. Click the direction arrow to control the camera. 1). Click up/down direction button to select the item. 2). Click Iris + to confirm the selection. 3). Click left/right direction button to adjust the value of the selected item. 3.1 VIDEO FORMAT You can set the video format to 2MP@30fps, 2MP@25fps, PAL or NTSC. -
Page 14: Video Settings
Figure 3-3 B&W IR LIGHT You can turn on/off the IR LIGHT to meet different circumstances. SMART IR The Smart IR function is used to adjust the light to its most suitable intensity, and prevent the image from over exposure. -
Page 15: Image Mode
VIDEO SETTINGS IMAGE MODE WHITE BALANCE BRIGHTNESS CONTRAST SHARPNESS SATURATION MIRROR BACK EXIT SAVE & EXIT Figure 3-5 VIDEO SETTING IMAGE MODE IMAGE MODE is used to adjust the image saturation, and you can set it to STD (Standard) or HIGH-SAT (High Saturation). -
Page 16: Factory Default
HV: The image flips 180° both horizontally and vertically. 3.5 FACTORY DEFAULT Reset all the settings to the factory default. 3.6 EXIT Move the cursor to EXIT and click Iris+ to exit the menu. 3.7 SAVE & EXIT Move the cursor to SAVE & EXIT and click Iris+ to save the settings, and exit the menu.