Advertisement
Quick Links
Advertisement
Related Manuals for Dancover ARROW 2,6
Summary of Contents for Dancover ARROW 2,6
- Page 1 Manual Greenhouse ARROW 2,6 20-03-2018...
- Page 2 Height 2,47 m width 2,6 m Length – any divisible by 2 m...
- Page 3 Assembly and operation of the greenhouse should be performed in strict compliance with the assembly manual and operation rules as specified in the technical certificate. The technical certificate must be preserved. Description Greenhouse ARROW is intended to create the microclimate favorable for growing garden and allotment crops in gardens and household plots.
- Page 4 Technical certificate Detailed list of parts for Greenhouse ARROW Chart 4 Marking Name Quantity (pcs) Package 1 (beams and straight parts) Beam Door diagonal part Door diagonal strap Ventilating window horizontal part Ventilating window vertical part Hooks Package 2 (arch parts) 4н...
- Page 5 Technical certificate Detailed list of parts for Inset Chart 5 Package 1 Beam Package 2 Support Stand 4н Lower arch 4в Upper arch Horizontal strainer Side brace Brace spreader Reinforcement nogging piece Package 3 Ridge profile Package 4 Lower wire bandage Upper wire bandage Ridge strap Screw М5х10...
- Page 6 Technical certifi cate Operation rules Before the start of operation, the When the greenhouse is assembled When the greenhouse is assembled greenhouse should be assembled and by a third party the customer should supervise the quality of works to ensure installed as prescribed in the manual.
- Page 7 Warranty responsibility Warranty responsibility 1. The manufacturer shall be responsible for the complete set of parts for the greenhouse frame. 2. The manufacturer shall be responsible for assemblability of the greenhouse in accordance with the manual. 3. The manufacturer shall be responsible for the greenhouse endurance in the specified weather conditions.
- Page 8 Manual Installation manual for Greenhouse ARROW introduction General view of the frame is given in Picture 1 . Parts should be installed in such a way that side selves of the profile are facing the surface cover. The frame is assembled of numbered parts. Symbols: Some parts may have spare -arrow shows the direction of...
- Page 9 Manual General view of the frame (Greenhouse ARROW) Pic. 1 4В А Д 4В В 4Н 4Н Б Е Г 4Н 4Н 4В 4В 4Н Angle Ridge strap Angle Angle Support hook А Б В (view from outside) (view from inside) (view from outside) 4В...
- Page 10 Manual General view of the frame, Greenhouse ARROW Pic. 2 General view of the inset for Greenhouse ARROW. Each inset extends the greenhouse length by 2 m. Pic. 3 Greenhouse ARROW extended by any number of insets. 2577 Pic. 4 Plan of greenhouse stands resting on the foundation...
- Page 11 Manual Installation steps Perform the assembly next to the installation site of the greenhouse. Perform the assembly in accordance with the pictures of assembly stages and the joints as shown in Pic. 5...12. The pictures illustrate assembly of a 4 m long greenhouse. The required length of a greenhouse is attained by adding corresponding parts from Inset package(s).
- Page 12 Manual Assembly stages Fasten arches 4н to arches 4в on 4в 4н the one side of the 4н greenhouse. 4н 4н 4н 4н Pic. 7 Fasten beams 2 to arches 4н 4н Pic. 8 Pic. 8 4н Similarly, install arches 4н...
- Page 13 Manual Assembly stages А В Г Е Д 4н 4н Б Pic. 11 4в А Б В 4н Г Д Inside the greenhouse frame, install side braces on each arch (parts 10). A side brace in assembled of two parts 10. Brace spreader 11 is installed at the joint 4н...
- Page 14 Manual Door assembly Assembly the door and the butt end ventilating window from parts 12, 13, 14, 15, 19, 20 (Pic. 12) Window А А Door Б Б Pic. 12...
- Page 15 Manual Surface cover cutting and fitting Warning! When cutting the surface cover in windy weather, fix the edges of polycarbonate sheets with a load. CUT THE POLUCARBONATE SHEET IN STRICT ACCORDANCE WITH PIC. 13 AND PIC. 14 Honeycombed polycarbonate sheet 2100 x 6000 mm Lower strip Cut the surface cover sheet for butt ends.
- Page 16 Manual The polycarbonate should be installed with the strongly defined outer Крепление покрытия side (towards the sun), having a protective layer (always make sure when purchasing or before installation). The protective layer is usually on the side with inscriptions on the packaging film. On the other side of the sheet the film is clear.
- Page 17 Manual Раскрой и крепление покрытия торца Cutting out and fastening the cover surface marking Pieces of cover surface above the door should be cut out as applicable from remaining pieces of polycarbonate. 4в Mark the cover surface for parts 4в in oversize, lining up the lower edge of the sheet with the lower edge of part 5 (Pic.15).
- Page 18 Manual Cutting out and fastening cover surface Door weather Рiс.18 hinge strip. Scotch tape Cover handle surface surface Cover surface handle Scotch tape Scotch tape Door weather Stud pin Door weather Hinge strip strip. washer strip. hinge Cover surface handle Cover surface washer Angle...
- Page 19 Manual Cutting out and fastening cover surface Pic.20 Place the butt end strap 16 onto butt end cover Butt end surface and fasten it onto part 5 through the surface Screw cover М5х50 (Pic.20 and Pic.24). Under part 16 there is a joint between parts of butt end cover surfaces.
- Page 20 Manual Cutting out and fastening cover surface Washer butt end surface screw М4х10 Part 16 angle hook Рic.24 Ground level Install washers on the butt end as shown in Pic.24. Install the angle for hooks on the butt end and the door to fi x it in the open position Pic.24 screw М5х10 Install tubular reinforcements for door...
- Page 21 Manual Cutting out and fastening cover surface 11. Insert wire Use straight part of the This construction allows rotatorfor door closing tube running to bend to push the door in the in free holes (against rotator in the opposite closed position, being the stop) through direction (Fig.
- Page 22 Manual Cutting out and fastening cover surface Cellular polycarbonate shall be installed strictly defi ned side out (towards the sun), which has a protective layer. The protective layer is usually at the side with the inscriptions on the transport fi lm. The fi lm on the other side of sheet is transparent.
- Page 23 Manual Cutting out and fastening cover surface Before coating it is necessary to cut the outer surface of the upper polycarbonate sheet for bending on the ridge (middle of sheet)!. The arrow on the details is directed L=1,05м to the front side х2 greenhouse х1...
- Page 24 Manual Cutting out and fastening cover surface do not fully tighten! х3 х3...
- Page 25 Manual Cutting out and fastening cover surface one-sided adhesive tape х1...
- Page 26 Manual Cutting out and fastening cover surface L=1,0м х1 х3 х3 х4 х4 х4...
- Page 27 Manual Cutting out and fastening cover surface Details of the ridge profi le are connected along the length with the threaded end of the screw directed outside screw М5х14...
- Page 28 Manual Cutting out and fastening cover surface Ridge profile х1 х1 х1 х1 х1 х1 х1 Upper х2 wire bandage Upper х2 wire bandage...
- Page 29 Contact information Head office: Dancover A/S For more information Nordre Strandvej 119 G please visit: 3150 Hellebæk www.dancovershop.com Denmark National contact Denmark: 70 26 76 20 Spain: 911 436 828 denmark@dancover.com espana@dancover.com UK: 020 8099 7570 Italy: 02 479 21 198 uk@dancover.com...