Philips 8000 Series Service Manual page 36

EN 36 6. Q551.1E LA
Table 6-3 White D alignment values - LED - Minolta CS-200
Value Cool (11000K)
x 0.276
y 0.282
If you do not have a colour analyser, you can use the default
values. This is the next best solution. The default values are
average values coming from production.
• Select a COLOUR TEMPERATURE (e.g. COOL,
NORMAL, or WARM).
• Set the RED, GREEN and BLUE default values according
to the values in Table
• When finished press OK on the RC, then press STORE (in
the SAM root menu) to store the aligned values to the NVM.
• Restore the initial picture settings after the alignments.
Table 6-4 White tone default setting 32" (Monet)
White Tone
Colour Temp
Normal
Cool
Warm
Table 6-5 White tone default setting 32" (Rubens)
White Tone
Colour Temp
Normal
Cool
Warm
Table 6-6 White tone default setting 37" (Monet)
White Tone
Colour Temp
Normal
Cool
Warm
Table 6-7 White tone default setting 40" (Monet)
White Tone
Colour Temp
Normal
Cool
Warm
Table 6-8 White tone default setting 40" (Rubens)
White Tone
Colour Temp
Normal
Cool
Warm
Table 6-9 White tone default setting 46" (Monet)
White Tone
Colour Temp
Normal
Cool
Warm
2010-Jun-25
Alignments
Normal (9000K) Warm (6500K)
0.287 0.313
0.296 0.329
6-4.
e.g. 32PFL8605x/xx
R G B
127 124 99
126 126 115
127 115 56
e,g, 32PFL9705x/xx
R G B
t.b.d. t.b.d. t.b.d.
t.b.d. t.b.d. t.b.d.
t.b.d. t.b.d. t.b.d.
e.g. 37PFL8605x/xx
R G B
t.b.d. t.b.d. t.b.d.
t.b.d. t.b.d. t.b.d.
t.b.d. t.b.d. t.b.d.
e.g. 40PFL8605x/xx
R G B
t.b.d. t.b.d. t.b.d.
t.b.d. t.b.d. t.b.d.
t.b.d. t.b.d. t.b.d.
e.g. 40PFL9705x/xx
R G B
t.b.d. t.b.d. t.b.d.
t.b.d. t.b.d. t.b.d.
t.b.d. t.b.d. t.b.d.
e.g. 46PFL8605x/xx
R G B
t.b.d. t.b.d. t.b.d.
t.b.d. t.b.d. t.b.d.
t.b.d. t.b.d. t.b.d.
Table 6-10 White tone default setting 46" (Rubens)
White Tone
Colour Temp
Normal
Cool
Warm
6.3.2 Ambilight
Every ambient light module is aligned by a matrix and by the
brightness. After replacement of a module, the brightness must
be aligned with the other modules:
1. Go to SAM.
2. Select "Alignments".
3. Select "Ambilight". A white test pattern shall be displayed.
4. Select the number of the module that have to be aligned.
Module 1 is the first one which will come across according
the wire connections starting by the small signal panel and
proceed towards the ambient light modules.The first
module will be attached to the next module 2. Module
number 2 to number 3 etc.
5. Align the brightness compaired with the neighbouring
modules. The brightness is automatically stored.
6. Select one of 10 matrixes which color correspond with the
neighbouring modules, "matrix 0" is the factory alignment
and can always be retrieved.
7. The alignment is stored automatically.
6.3.3 TCON/VCOM alignment
Sets with forward integration have the TCON on SSB. The
alignment of this TCON is stored in the SSB, and is related to
the used display. When an SSB or a display is replaced, a new
value must be entered.
A default value (see table below) is copied from the display file
(after entering the correct display code) and is shown in the
SAM menu. But on top of this, the default value can be
overruled manually via the menu item "TCON alignment".
The current value is shown with 4 digits, and can be changed
by a digit entry. After pressing "OK", the value is stored.
The menu item "Reset TCON alignment" can be used to return
to the default value from the display file. A notification is shown:
"TCON alignment has been reset".
Table 6-11 TCON/VCOM default settings
Supplier
to be defined
6.4 Option Settings
6.4.1 Introduction
The microprocessor communicates with a large number of I
ICs in the set. To ensure good communication and to make
digital diagnosis possible, the microprocessor has to know
which ICs to address. The presence / absence of these
PNX51XX ICs (back-end advanced video picture improvement
IC which offers motion estimation and compensation features
(commercially called HDNM) plus integrated Ambilight control)
is made known by the option codes.
Notes:
• After changing the option(s), save them by pressing the OK
button on the RC before the cursor is moved to the left,
select STORE in the SAM root menu and press OK on the
RC.
• The new option setting is only active after the TV is
switched "off" / "stand-by" and "on" again with the mains
switch (the NVM is then read again).
back to
div. table
e.g. 46PFL9705x/xx
R G
t.b.d. t.b.d.
t.b.d. t.b.d.
t.b.d. t.b.d.
Panel TCON/VCOM Alignment
to be defined
to be defined
B
t.b.d.
t.b.d.
t.b.d.
2
C