Makita 4351CT Technical Information
Hide thumbs
Also See for 4351CT:
- Instruction manual (61 pages) ,
- Specifications (2 pages) ,
- Instruction manual (53 pages)
Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
T
ECHNICAL INFORMATION
Model No.
Description
C
ONCEPT AND MAIN APPLICATIONS
Models 4351T, 4351CT and 4351FCT have been developed
as the successor models of 4341T series models.
In addition to the advantages of the predecessor models,
feature new exterior design with ergonomic rubberized handle.
Top handle type models are also available as 4350T series models.
S
pecification
4351T
Voltage (V)
110
120
220
230
240
4351CT/ 4351FCT
110
120
220
230
240
Specification
No load speed: strokes per min.
Length of stroke: mm (")
Shank type
Capacities: mm (")
Cut settings
Toolless blade change
Variable speed control by dial
Soft start
Constant speed control
LED Job light
Protection against electric shock
Power supply cord: m (ft)
Net weight: kg (lbs)
*1 when cutting with optional blade No.B-16L *2 Australia, New Zealand: 2.0m (6.6ft)
S
tandard equipment
Jig saw blade B-10 ........ 2
Jig saw blade BR-13 ...... 2
Jig saw blade B-22 ........ 2
Note: The standard equipment for the tool shown above may differ from country to country.
O
ptional accessories
Jig saw blades No.51, 58, 59, B-8, B-10 to B-19, B-21 to B-27, B-16L, BR-13
Guide rule, Guide rail, Guide rail adaptor, Anti-splintering device
Hose complete 28-5, Dust nozzle
4351T, 4351CT, 4351FCT
Jig Saw
Cycle (Hz)
Current (A)
5.6
50/60
5.1
50/60
2.8
50/60
2.7
50/60
2.5
50/60
6.9
50/60
6.3
50/60
3.4
50/60
3.3
50/60
3.2
50/60
Model
4351T
Wood*
1
Steel
Aluminum
2.4 (5.3)
Cover plate ....................... 1
Anti-splintering device ..... 1
Hex wrench 4 ................... 1
H
Continuous Rating (W)
Input
580
---
580
580
580
720
---
720
720
720
4351CT
2,800
26 (1)
B-type
135 (5-5/16)
10 (3/8)
20 (25/32)
3 Orbital settings + Straight cutting
Yes (Push-in-lock system)
No
No
No
No
Double insulation
2.5 (8.2)*
Plastic carrying case ...... 1
Dust nozzle*
*3
for European countries only
L
W
Dimensions: mm (")
Length (L)
271 (10-11/16)
Width (W)
73 (2-7/8)
Height (H)
187 (7-3/8)
Max. Output (W)
Output
300
300
300
300
300
320
320
320
320
320
4351FCT
800 - 2,800
Yes
Yes
Yes
No
2
2.5 (5.5)
................ 1
3
PRODUCT
P 1 /15
550
550
550
550
550
700
700
700
700
700
Yes
Advertisement
Related Manuals for Makita 4351CT
Summary of Contents for Makita 4351CT
- Page 1 Description Jig Saw ONCEPT AND MAIN APPLICATIONS Models 4351T, 4351CT and 4351FCT have been developed as the successor models of 4341T series models. In addition to the advantages of the predecessor models, feature new exterior design with ergonomic rubberized handle.
- Page 2 1R269 Bearing extractor < 1 > Lubrication Apply Makita grease FA. No.2 to the portions marked with black triangle, and machine oil No.120 to the portions marked with gray triangle to protect parts and product from unusual abrasion. Linear guide...
- Page 3 P 3 / 15 epair [2] Disassembling Tool opener 1. Remove M5x18 Hex socket head bolt. Base is separated from product. (Fig. 1) 2. Remove M4 + Pan head screw. Tool opener and Torsion spring 6 are separated. (Fig. 2) Fig.
- Page 4 P 4 / 15 epair [5] Disassembling Gear housing cover section 1. After separating Safety wire from Gear housing cover, remove four 4x16 Tapping screws CT . Gear housing cover is separated from Gear housing as illustrated in Fig. 6. Fig.
- Page 5 P 5 / 15 epair [6] Assembling Gear housing cover section 1. Assemble Tool opener to Gear housing cover with referring to Figs. 1, 2 and 3 in page 3. 2. Put Leaf spring in Gear housing cover. Pay attention to its assembling direction. (Fig. 9) Insert Rod into Gear housing cover.
- Page 6 P 6 / 15 epair 7. Install Stop ring E-3 to secure Pin 4 as illustrated in Fig. 15. 8. Check whether Slider can reciprocate on Linear guides smoothly. Note: If Slider does not reciprocate smoothly, Linear guides may lean to the left or the right. Try again to assemble Linear guides correctly.
- Page 7 Note: Be careful not to lose Push pin when disassembling. [8] Assembling blade holder 1. Apply Makita grease FA No.2 to Push pin. Insert Push pin to Rod. Insert the short hook end of Torsion spring 15 to Rod. (Fig. 20) 2.
- Page 8 P 8 / 15 epair [9] Disassembling parts in Gear housing 1. After separating Safety wire from Gear housing cover, remove four 4x16 Tapping screws CT . Gear housing cover is separated from Gear housing as illustrated in Fig. 25. Fig.
- Page 9 P 9 / 15 epair [10] Assembling parts in Gear housing 1. Pass the shaft of Gear housing through Flat washer 8. (Fig. 28) 2. After assembling Seal plate to Push plate, pass the shaft of Gear housing through Push plate with Seal plate. (Fig. 29) 3.
- Page 10 P 10 / 15 epair [11] Disassembling armature 1. With referring to the following section, disassemble Head covers L and R, and gear housing cover. [4] Disassembling Head cover section in page 3 [5] Disassembling Gear housing cover section" at page 4 2 .
- Page 11 P 11 / 15 epair 6. Remove Ball bearing 607 LLB from Armature shaft as illustrated in Fig. 38. Fig. 38 1R269 Insulation washer Ball bearing 607 LLB [12] Assembling armature Do not assemble the used self lock. The self lock has to be always replaced with the fresh one. Note: Pay attention to the assembling direction of Self lock and Wave washer 6.
- Page 12 P 12 / 15 epair [14] Disassembling Motor section 1. Remove Rear cover from Motor housing by unscrewing 4x18 Tapping screw. 2. Disconnect the connector of LED circuit. the electric parts module can be pulled out from Motor housing. (Fig. 43) Fig.
- Page 13 P 13 / 15 ircuit diagram in the rear of motor housing 4351CT (with controller, without LED job light) 4351FCT (with controller and LED job light) : Connecting with terminal Switch block unit Noise Noise suppressor is not used suppressor in some countries.
-
Page 14: Wiring Diagram
P 14 / 15 ircuit diagram in the rear of motor housing 4351T (without controller and LED jog light) : Connecting with terminal Switch block unit Noise In case of noise suppressor with suppressor two lead wires, put it into switch block unit. - Page 15 P 15 / 15 iring diagram 4351FCT Groove Lead wire holder Hole for Lead wire Lead wire holders Lead wire for of LED circuit LED circuit Lead wire for LED circuit Put Lead wire for LED circuit into Lead wire holder. Route Lead wire for LED circuit as follows: 1) through the hole of Motor housing 2) in Lead wire holders...