Advertisement
Cabling Connections
To the Workstation...
1. Connect an Ethernet cable (RJ-45 to RJ-45) to the TPE
port of the XM500 and to the Ethernet LAN socket with
the IP address that was configured for the modem.
2. Connect the RJ-45 plug of the RS-232C cable (included
with the modem) to a standard RS-232 cable.
NOTE: It is necessary to purchase one of these cables
at your nearest computer parts store.
3. Connect standard RS-232 cable to PC port number one.
4. Connect the power supply to the XM500.
5. Turn on the XM500.
To Controller (XL50/100/500,XDM506,XM100A)...
1. Connect an Ethernet cable (RJ-45 to RJ-45) to the TPE
port of the XM500 and to the Ethernet LAN socket with
the IP address that was configured for the modem.
2. Connect the RJ-45 plug of the RS-232C cable (included
with the modem) to the controller.
NOTE: The 25 to 9 pin adapter is required for the
XL50/100/500 controllers. A XW571 cable
(purchased separately) is required for XDM506
and XM100A.
3. Connect the power supply to the XM500.
4. Turn on the XM500.
To an SLTA...
1. Connect Ethernet cable (RJ-45 to RJ-45) to the XM500
TPE port and to the Ethernet LAN socket with the IP
address that was configured for the modem.
2. Connect the RJ-45 plug of the RS-232C cable to the
SLTA Modem Cable.
NOTE: It is necessary to purchase separately the
Modem Installation Cable (Honeywell part
number 32002517-001).
3. Set SLTA-10 dipswitches for modem communications
(see form 95-7511-2).
4. Connect the power supply to the XM500.
5. Turn on the XM500.
6. Check to ensure both the Power and Link LED on the
modem remain lit. If the link light does not remain on,
the modem is not connected to a network.
L
S
™ and L
ON
TATION
1. Begin from the desktop.
2. Double click My Computer.
3. Double click Control Panel.
4. Double click Modems.
5. Click Add.
S
™ Configuration
ON
PEC
6. Click the box Don't detect my modem; I will select it
from a list.
7. Click Next.
8. Under Manufacturers column, click Standard Modem
Types.
9. Under Models column, click Standard 28800 bps
Modem.
10. Click Next.
IMPORTANT
Determine whether the modem is connected to
COM1 or COM2.
11. Choose the appropriate COM port from the list.
12. Click Next.
13. Wait for indication of proper modem configuration.
14. Click Finish.
15. You should be returned to the main screen and see the
Standard 28800 bps modem has been configured.
16. Click Properties.
17. Change the Maximum Speed from 28800 to 38400.
18. Click OK.
NOTE: The modem is now configured to run at its highest
baud rate in L
These programs will also now recognize the modem.
Configuration for XBS
Refer to the XBS Checkout and Test (Form 74-3422) for
instructions on configuring the workstation for modem
communication via a XPC500 card or com port.
Modem module menu
In the modem module menu do the settings equivalent to a
normal modem set-up.
IMPORTANT
1. The IP address is entered in the same fields where
a telephone number would have been entered.
2. The XM500 accepts an IP address entered with
commas like 160,221,71,130 or entered with dots
(e.g., 160.221.71.130), or as 4 3-digit octets with
leading zeros and no spaces (e.g., 160221071130).
Baud rate
The XBS supports baud rates up to 38.400 bps.
IMPORTANT
If baud rates 19.200 and 38.400 bps are to be used
the autobauding MUST be switched <on>.
1. At Sending PC, wait for <connect>.
2. A transparent data communication should be possible.
3. Verify this:
a. Transmit some information.
b. Check that it is received on the target PC.
5
XM500 TCP/IP MODEM
S
™ 3.0 and L
S
ON
TATION
ON
™.
PEC
74-3468—3
Advertisement
