Advertisement
Quick Links
T
ECHNICAL INFORMATION
Models No.
Description
C
ONCEPT AND MAIN APPLICATIONS
Model 5477NB has been developed as the cost-competitive successor
tool of the current 5277NB.
S
pecification
Voltage (V)
120
No load speed: rpm=min.
Saw blade: mm (")
Max. cutting
capacities: mm (")
Protection from electric
Cord length: m (ft)
Net weight: kg (lbs)
S
tandard equipment
TCT saw blade .......................... 1
Hex wrench ................................ 1
Note: The standard equipment for the tool shown above may differ by country.
O
ptional accessories
Circular saw blades
Guide rule
Tool hook
5477NB
Hypoid Saw 185mm (7-1/4")
Cycle (Hz)
Current
15
50 - 60
-1
Diameter
Hole diameter
at 90 degrees
at 45 degrees
at 50 degrees
Continuous Rating (W)
Input
4,500
185 (7-1/4)
15.88 (5/8)
60 (2-3/8)
44 (1-3/4)
40 (1-9/16)
Double insulation
3.0 (9.8)
6.3 (13.9)
W1
W2
L2
L1
Dimensions: mm (")
Length (L1)
442 (17-3/8)
Width (W1)
Height (H1)
Height (H2)
Base Size: mm (")
Length (L2)
295 (11-5/8)
Width (W2)
132 (5-3/16)
Max. Output (W)
Output
1,000
2,300
PRODUCT
P 1/ 8
H2
H1
183 (7-1/4)
254 (10)
186 (7-3/8)
Advertisement
Related Manuals for Makita 5477NB
Summary of Contents for Makita 5477NB
- Page 1 P 1/ 8 5477NB Models No. Description Hypoid Saw 185mm (7-1/4") ONCEPT AND MAIN APPLICATIONS Model 5477NB has been developed as the cost-competitive successor tool of the current 5277NB. Dimensions: mm (") Length (L1) 442 (17-3/8) Width (W1) 183 (7-1/4)
-
Page 2: Necessary Repairing Tools
When assembling Gear section; 1) Wash the inside of Gear housing complete clean with kerosene. 2) Put 30cc Lubricant oil VG220 (Makita part No. 041005-1A: 20 liters per tank) as illustrated in Fig. 1 to protect parts and product from unusual abrasion. - Page 3 P 3/ 8 epair [3] DISASSEMBLY/ ASSEMBLY OF BASE (cont.) DISASSEMBLING 2) Remove the other Bow stop ring E-12, Lever plate, M8-13 Hex nut, Flat washer 8 (small) and M8x24 Cap square neck bolt on the angular guide of Base. (Fig. 4) 3) Remove M8 Flat head screw on the angular guide.
- Page 4 P 4/ 8 epair [4] DISASSEMBLY/ ASSEMBLY OF GEAR SECTION (Cont.) DISASSEMBLING 4) Gear housing complete is secured with M5x35 Pan head screws (2pcs.) on Spindle lock button side and with the other M5x35 Pan head screws (2pcs.) on Blade case side. First, remove M5x35 Pan head screws (2pcs.) on Spindle lock button side.
- Page 5 P 5/ 8 epair [5] DISASSEMBLY/ASSEMBLY OF GEAR SECTION (cont.) DISASSEMBLING 10) Remove M5x18 Pan head screws (2pcs.). Remove Armature with Bearing retainer not to cause damage to Fan 45 in Gear housing complete. (Fig. 15) 11) Disassemble Spindle with Fan 45 by striking the Spindle end from Blade installation-side with plastic hammer. (Fig.
- Page 6 P 6/ 8 epair [6] DISASSEMBLY/ ASSEMBLY OF ARMATURE SECTION DISASSEMBLING Note: It is not necessary to remove Bearing box from Gear housing complete when replacing Armature. 1) Separate Base from Motor section. (Figs 2 to 5) 2) After Removing Depth guide from Motor housing complete, remove Carbon brush. 3) Separate Gear housing complete from Motor housing complete after removing M5x35 Pan head screws (4pcs.).
- Page 7 P 7/ 8 epair [6] DISASSEMBLY/ASSEMBLY OF ARMATURE SECTION (Cont.) ASSEMBLING 1) Mount Bearing retainer to Armature. Press-fit Ball bearing 6003LLB into Armature shaft. 2) Push new O ring 16 by hand until it contacts to the inner ring of Ball bearing 6003LLB as illustrated in Fig. 24. 3) Press-fit Ring 17 as illustrated in Fig.25.
- Page 8 P 8/ 8 [10] ADJUSTMENT IN POSITION OF LEVER PLATE FOR DEPTH GUIDE Fig. 28 The assembled angle of Lever plate and Depth guide has to be adjusted in the zone from 0 degree to 30 degrees as illustrated in Fig. 28. degrees Lever plate [11] ADJUSTMENT IN POSITION OF LEVER PLATE FOR ANGULAR GUIDE...