Table of Contents
Advertisement
3-1-2.
Precautions on Adjusting
1)
Connect the adjustment remote commander to CN1011 of VC-
256 board via CPC jig for BX/BK (J-6082-521-A). To operate
the adjustment remote commander, connect the AC power
adapter to the DC IN jack of CPC jig for BX/BK, or connect
the L series Info-LITHIUM battery to the battery terminal of
CPC jig for BX/BK.
2)
The adjustments of this unit are performed in the VTR mode
or camera mode.
To set to the VTR mode, set the power switch to "VCR or
PLAYER" or set the "Forced VTR Power ON mode" using the
adjustment remote commander (Note1).
To set to the Camera mode, set the power switch to "CAMERA"
or set the "Forced Camera Power ON mode" using the
adjustment remote commander (Note2).
After completing adjustments, be sure to exit the "Forced VTR
Power ON Mode" or "Forced Camera Power ON Mode".
(Note3)
3)
The front panel block (MI-041 board, microphone unit, video
light) need not be connected except during "IR transmitter
adjustment (DCR-TRV130)". To remove, disconnect the
following connector.
MI-041 board CN1002 (24P 0.5mm)
4)
As removing the cabinet (R) assembly (removing CN1007 of
the VC-256 board) means removing the lithium 3V power
supply (CF-1000 block BT101), data such as date, time, user-
set menus will be lost. After completing adjustments, reset these
data. If the cabinet (R) assembly has been removed, the self-
diagnosis data, data on history of use (total drum rotation time
etc.) will be lost. Before removing, note down the self-diagnosis
data (data of page: 2, address: B0 to C6) and the data on history
use (data of page: 2, address: A2 to AA and E0 to E2). (Refer
to "5-4.Service Mode".)
5)
The cabinet (R) assembly (CF-1000 block, LCD block) need
not be connected to operate the VTR block.(Note4) When
removing the cabinet (R) assembly, disconnect the following
connectors.
1. VC-256 board CN1007 (24P, 0.5mm)
2. VC-256 board CN1003 (20P, 0.8mm)
6)
The lens block (CD-281 board) need not be connected. To
remove, disconnect the following connectors.
1. VC-256 board CN1501 (14P, 0.5mm)
2. VC-256 board CN1551 (24P, 0.5mm)
7)
The EVF block (VF-129 board) need not be connected. To
remove, disconnect the following connectors.
VC-256 board CN1006 (4P, 1.0mm)
8)
By setting the "Forced VTR Power ON mode" or "Forced
Camera Power ON mode", the video section can be operate
even if the control switch block (SS-1000) has been removed.
When removing the control switch block (SS-1000), disconnect
the following connector.
VC-256 board CN1009 (5P 0.8mm)
Note1: Setting the "Forced VTR Power ON" mode (VTR mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 02, and press the PAUSE
button.
The above procedure will enable the VTR power to be turned on
with the control switch block (SS-1000) removed.
After completing adjustments, be sure to exit the "Forced VTR
Power ON mode".
Note2: Setting the "Forced Camera Power ON" mode (Camera mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press the PAUSE
button.
The above procedure will enable the camera power to be turned
on with the control switch block (SS-1000) removed.
After completing adjustments, be sure to exit the "Forced Camera
Power ON mode".
Note3: Exiting the "Forced Power ON" mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the PAUSE
button.
3) Select page: 0, address: 01, and set data: 00.
Note4: When the FK-1000 block or the CF-1000 block/CF-077 board is
removed, the VTR does an unusual movement for one after the
power is turned on.
5-35
Hide quick links:
Advertisement
Table of Contents
