1. Manuals
  2. Brands
  3. Canon Manuals
  4. Printer Accessories
  5. Finisher-R1
  6. Installation procedure

Canon Finisher-R1 Installation Procedure

Finisher, sorter, deliverytray
Hide thumbs Also See for Finisher-R1:
Table of Contents

Advertisement

Quick Links

See also: Service Manual , Installation Procedures
Installation Procedure
Finisher, Sorter, DeliveryTray
Finisher-R1
Nov 27 2003

Advertisement

Table of Contents
loading

Related Manuals for Canon Finisher-R1

Summary of Contents for Canon Finisher-R1

  • Page 1 Installation Procedure Finisher, Sorter, DeliveryTray Finisher-R1 Nov 27 2003...
  • Page 3 When changes occur in applicable products or in the contents of this manual, Canon will release technical information as the need arises. In the event of major changes in the contents of this manual over a long or short period, Canon will issue a new edition of this manual.
  • Page 4 Introduction Symbols Used This documentation uses the following symbols to indicate special information: Symbol Description Indicates an item of a non-specific nature, possibly classified as Note, Caution, or Warning. Indicates an item requiring care to avoid electric shocks. Indicates an item requiring care to avoid combustion (fire). Indicates an item prohibiting disassembly to avoid electric shocks or problems.
  • Page 5 Introduction The following rules apply throughout this Service Manual: 1. Each chapter contains sections explaining the purpose of specific functions and the relationship between electrical and mechanical systems with reference to the timing of operation. 　In the diagrams, represents the path of mechanical drive; where a signal name accompanies the symbol , the arrow indicates the direction of the electric signal.

  • Page 7: Table Of Contents

    Contents Contents 第 1 章　Installation Procedure 1.1 Making Pre-Checks ............................... 2 1.1.1Checking the Contents............................. 2 1.1.2Installing the Accessories ..........................3 1.1.3Selecting the Site of Installation........................4 1.2 Unpacking and Chacking the Components ......................6 1.2.1Unpacking ............................... 6 1.3 Installation Procedure............................13 1.3.1Preparing the Finisher for Installation......................
  • Page 8 Contents...
  • Page 9 Chapter 1　Installation Procedure...

  • Page 10: Making Pre-Checks

    Chapter 1 　 1.1 Making Pre-Checks 1.1.1 Checking the Contents 0003-1754 [10] [13] [14] [13] [11] [17] [15] [16] [14] [13] [12] [12] [14] [13] [11] [12] [13] [13] [14] F-1-1...

  • Page 11: 2Installing The Accessories

    Chapter 1 T-1-1 <Finisher-R1> <Saddle Finisher-R2> [1]Inlet guide upper 1 pc. [1]Inlet guide upper 1 pc. [2]Inlet guide lower 1 pc. [2]Inlet guide lower 1 pc. [3]Fixing plate (FC5-4196) 2 pc. [3]Fixing plate (FC5-4196) 1 pc. [5]Staple cartridge 1 pc. (3 blocks) [4]Fixing plate (FC5-4976) 1 pc.

  • Page 12: 3Selecting The Site Of Installation

    1.1.3 Selecting the Site of Installation 0003-1758 Select the site of installation, making sure that there will be enough space for work (e.g., handling paper). Be sure also that there will be no gap between the finisher and its host machine. <Finisher-R1>...
  • Page 13 Chapter 1 100 or more F-1-3 <Saddle Finisher-R2> 100 or more F-1-4 Install both the finisher and its host machine on a level floor without any step. Otherwise, the machines may suffer faults in paper movement.

  • Page 14: Unpacking And Chacking The Components

    Chapter 1 　 1.2 Unpacking and Chacking the Components 1.2.1 Unpacking 0003-1759 Memo: The machine is packed using tape and cushioning material to protect against vibration and shock during transit. Be sure to remove them before starting to install the machine. (It is a good idea to store away the removed tape and cushioning material for possible relocation of the machine, e.g., to a new site or for repairs.) 1) Take out the accessory box and the attachments from the shipping box.
  • Page 15 Chapter 1 F-1-6 3) Remove the cushioning material (Styrofoam) from the upper cover. 4) Slightly lift the front and rear casters, and remove the cushioning material (Styrofoam). Be sure to shift up the finisher by holding the upper left cover [1] (gray area). The finisher is rather heavy.
  • Page 16 F-1-8 7) Remove the fixing screw [1], and remove the 2 tray fixings [2]. F-1-9 8) In the case of the Finisher-R1, open the front door [1]. In the case of the Saddle Finisher-R2, open the front cover [2]. <Finisher-R1>...
  • Page 17 Chapter 1 F-1-10 <Saddle Finisher-R2> F-1-11 9) Remove the tape and the cushioning material [1] (Styrofoam) from the stapler. F-1-12...
  • Page 18 Chapter 1 　 10) In the case of the Finisher-R1, close the front door. In the case of the Saddle Finisher-R2, go to the next step while keeping the front cover open. ■ Removing the Stitcher Fixing Member (only for the Saddle Finisher-R2) 1) Slide out the stitcher unit [1] to the front, and remove the tape.
  • Page 19 Chapter 1 is not used for a long time. Once you have removed the plate and its fixing screws, it is a good idea to store them away for future use. 1) Remove the 7 screws [1], and detach the lower right cover [2]. F-1-15 2) Remove the fixing screw [1], and detach the releasing plate (front) [2].
  • Page 20 Chapter 1 　 F-1-17 4) Mount the lower right cover you have removed using the 7 screws.

  • Page 21: Installation Procedure

    0003-1760 Be sure to mount the inlet guide and the fixing plate before connecting the finisher to its host <Finisher-R1> machine. 1) Mount the rail [1] to the finisher using 2 screws [2] 1) If a delivery tray is found on the delivery assembly (binding;...

  • Page 22: 3Connecting To The Host Machine

    Procedure. outlet. <Finisher-R1> 1) Make the connection by matching the pin found on Use FC5-4196 for both fixing plates [1] and [2]. the fixing plate (rear) of the host machine against the hole in the finisher.
  • Page 23 Chapter 1 F-1-25 F-1-24 4) In the case of the Finisher-R1, open the front door 2) Remove the screw [1], and detach the upper rear [1] and remove the 3 screws [2], then detach the front cover (small) [2] of the finisher.

  • Page 24: 4Checking The Height/Tilt

    Chapter 1 　 front cover. In the case of the Finisher-R1, do not attach the front cover until you have adjusted the height/tilt. 1.3.4 Checking the Height/ Tilt 0003-1767 Depending on the condition of the floor of the site of installation, you may need to adjust the height or the tilt of the finisher.
  • Page 25 Chapter 1 3 1.5mm 53 2mm F-1-30 F-1-29 3) If the height/tilt is correct, end the installation work by referring to “Work After Making Checks/ 2) Check the tilt of the finisher and its host machine. Adjustments.” If the height/tilt is not correct, see the Check to make sure that the gap between the upper instructions in “Adjusting the Height/Tilt.”...

  • Page 26: Making Adjustments

    <Finisher-R1> In the case of the Finisher-R1, you will need to remove its auxiliary ring and rear foot cover. Be sure to remove the auxiliary ring with the finisher and its host machine intact, thus preventing the machine from tumbling over.
  • Page 27 Chapter 1 F-1-32 <Saddle Finisher-R2> 1) Open the front cover; then, from the back of the front cover, remove the fixing screw, and detach the pliers [1]. F-1-33 ■ Adjusting the Height 1) Loosen the 2 fixing screws [1] each of the casters at the front and rear of the finisher pickup side. 2) If you want to increase the height of the finisher, turn the adjusting bolt [2] in the direction of arrow A of the figure.
  • Page 28 Chapter 1 　 F-1-34 ■ Adjust the Tilt 1) Loosen the 2 fixing screws [1] 2 each on the front and rear casters of the finisher delivery side. 2) If you want to decrease the gap between the finisher and its hot machine, turn the adjusting bolt [2] in the direction of A.

  • Page 29: 2Work After Making Checks/Adjustments

    5) End the installation work by referring to the instructions in “Work After Making Checks/Adjustments.” 1.4.2 Work After Making Checks/Adjustments 0003-1770 <Finisher-R1> 1) If you removed the auxiliary ring, attach the left rear foot cover; then, adjust the auxiliary rail to suit needs of the user, and mount it in place using 4 screws.
  • Page 30 Chapter 1 　 5) Connect the finisher ant the host machine using the interface cable[1]. 6) Fix the cable clamp [2] to the host machine, and route the interface cable [1] through it. When connecting the interface cable, be sure to turn off the host machine and disconnect its power plug from the power outlet before starting the work.
  • Page 31 Chapter 1 F-1-39 4) Connect the finisher and its host machine with the interface cable [1]. 5) Fit the cable clamp [2] to the host machine, and route the interface cable [1] through it. When installing the interface cable, be sure to turn off the host machine and disconnect its power plug from the power outlet.

  • Page 32: Attaching The Labels Etc

    Chapter 1 　 1.5 Attaching the Labels etc. 1.5.1 Attaching the Various Labels 0003-1771 1) Attach the tray label [1] to the tray as indicated. 2) Attach the settings label [2] within the frame of the tray label to suit the user habit of the user. 3) In the case of the Saddle Finisher-R2, attach the Bookmaking label [3] to the saddle tray as shown.
  • Page 33 Nov 27 2003...

Table of Contents