Advertisement
Installation Instructions /
4
CONFIGURE THE 5877
TO USE WITH 5800 SERIES WIRELESS KEYS, ENROLL
WIRELESS KEYS INTO MODULE
1. Press (one second) and release the Program button; the LED
will start flashing GREEN.
2. Press the Wireless Key button to enroll it and the LED will stop
flashing GREEN. [Note: If no Wireless Key button is pushed,
the "enroll" program mode times out after 2 minutes.]
3. Repeat the process for each Wireless Key button; up to 7
buttons total.
4. Test by pressing each Wireless Key button enrolled in the relay
module; the relay module should click for each Wireless Key
button press.
TO DELETE ALL WIRELESS KEY BUTTONS
Press and continue to hold the Program button; the LED turns
RED, then turns off, then RED again; release the Program button.
This takes about 15 seconds.
4
CONFIGURE THE 5877 – FR-Can
TO USE WITH 5800 SERIES WIRELESS KEYS, ENROLL
WIRELESS KEYS INTO MODULE
1.
Press (one second) and release the Program button; the LED
will start flashing GREEN.
2.
Press the Wireless Key button to enroll it and the LED will stop
flashing GREEN. [Note: If no Wireless Key button is pushed,
the "enroll" program mode times out after 2 minutes.]
3.
Repeat the process for each Wireless Key button; up to 7
buttons total.
4.
Test by pressing each Wireless Key button enrolled in the relay
module; the relay module should click for each Wireless Key
button press.
TO DELETE ALL WIRELESS KEY BUTTONS
Press and continue to hold the Program button; the LED turns
RED, then turns off, then RED again; release the Program button.
This takes about 15 seconds.
4
CONFIGURE THE 5877 – LA-ES
TO USE WITH 5800 SERIES WIRELESS KEYS, ENROLL
WIRELESS KEYS INTO MODULE
1.
Press (one second) and release the Program button; the LED
will start flashing GREEN.
2.
Press the Wireless Key button to enroll it and the LED will stop
flashing GREEN. [Note: If no Wireless Key button is pushed,
the "enroll" program mode times out after 2 minutes.]
3.
Repeat the process for each Wireless Key button; up to 7
buttons total.
4.
Test by pressing each Wireless Key button enrolled in the relay
module; the relay module should click for each Wireless Key
button press.
TO DELETE ALL WIRELESS KEY BUTTONS
Press and continue to hold the Program button; the LED turns
RED, then turns off, then RED again; release the Program button.
This takes about 15 seconds.
4
CONFIGURE THE 5877 – LA-PT
TO USE WITH 5800 SERIES WIRELESS KEYS, ENROLL
WIRELESS KEYS INTO MODULE
1.
Press (one second) and release the Program button; the LED
will start flashing GREEN.
2.
Press the Wireless Key button to enroll it and the LED will stop
flashing GREEN. [Note: If no Wireless Key button is pushed,
the "enroll" program mode times out after 2 minutes.]
3.
Repeat the process for each Wireless Key button; up to 7
buttons total.
4.
Test by pressing each Wireless Key button enrolled in the relay
module; the relay module should click for each Wireless Key
button press.
TO DELETE ALL WIRELESS KEY BUTTONS
Press and continue to hold the Program button; the LED turns
RED, then turns off, then RED again; release the Program button.
This takes about 15 seconds.
FEDERAL COMMUNICATIONS COMMISSION STATEMENT:
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User Manual. Unauthorized changes or
modifications could void the user's authority to operate the equipment.
CLASS B DIGITAL DEVICE STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may
cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the
specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• If using an indoor antenna, have a quality outdoor antenna installed.
• Reorient the receiving antenna until interference is reduced or eliminated.
• Move the radio or television receiver away from the receiver/control.
• Move the antenna leads away from any wire runs to the receiver/control.
• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.
• Consult the dealer or an experienced radio/TV technician for help.
Honeywell is a registered trademark of Honeywell International Inc. All other trademarks are the
properties of their respective owners. All rights reserved. Made in Taiwan.
For the latest U.S. warranty information, please visit: www.honeywell.com/security/hsc/resources/wa or
Please contact your local authorized Honeywell representative for product warranty information.
5877
Relay Receiver /
Instructions de montage (FRC) / Installation Instructions(LAES) / Installation Instructions (LAPT)
Relay Receiver / Relay Receiver / Relay Receiver
TO USE FOR SYSTEM STATUS [Optional] ENROLL RF HOUSE ID CODE INTO MODULE
NOTE: The System Control Panel must be capable of transmitting system status, for example, an
L5000, L3000, or a VISTA Panel with a 5883 transceiver. Ensure the House ID is enabled in the
panel programming.
1.
Press (one second) and release the Program button; the LED will start flashing GREEN.
2.
IMMEDIATELY press (one second) and release the Program button again. The LED will start
flashing ORANGE.
3.
Disarm or Arm the control panel. The LED stops flashing ORANGE and then shows the status of
the control panel (see LED indications).
[Note: If no House ID code is enrolled, the enroll program mode times out after 2 minutes.]
LED STATUS
INDICATION
Flashing RED
Armed AWAY
Solid RED
Armed STAY
Solid GREEN
System READY
Flashing ORANGE
ALARM / Panic
4.
Test the status by arming and disarming the system in both AWAY and STAY Modes.
TO USE FOR SYSTEM STATUS [Optional] ENROLL RF HOUSE ID CODE INTO MODULE
NOTE: The System Control Panel must be capable of transmitting system status, for example, an
L5000, L3000, or a VISTA Panel with a 5883 transceiver. Ensure the House ID is enabled in the
panel programming.
1.
Press (one second) and release the Program button; the LED will start flashing GREEN.
2.
IMMEDIATELY press (one second) and release the Program button again. The LED will start
flashing ORANGE.
3.
Disarm or Arm the control panel. The LED stops flashing ORANGE and then shows the status of
the control panel (see LED indications).
[Note: If no House ID code is enrolled, the enroll program mode times out after 2 minutes.]
LED STATUS
INDICATION
Flashing RED
Armed AWAY
Solid RED
Armed STAY
Solid GREEN
System READY
Flashing ORANGE
ALARM / Panic
4.
Test the status by arming and disarming the system in both AWAY and STAY Modes.
TO USE FOR SYSTEM STATUS [Optional] ENROLL RF HOUSE ID CODE INTO MODULE
NOTE: The System Control Panel must be capable of transmitting system status, for example, an
L5000, L3000, or a VISTA Panel with a 5883 transceiver. Ensure the House ID is enabled in the
panel programming.
1.
Press (one second) and release the Program button; the LED will start flashing GREEN.
2.
IMMEDIATELY press (one second) and release the Program button again. The LED will start
flashing ORANGE.
3.
Disarm or Arm the control panel. The LED stops flashing ORANGE and then shows the status of
the control panel (see LED indications).
[Note: If no House ID code is enrolled, the enroll program mode times out after 2 minutes.]
LED STATUS
INDICATION
Flashing RED
Armed AWAY
Solid RED
Armed STAY
Solid GREEN
System READY
Flashing ORANGE
ALARM / Panic
4.
Test the status by arming and disarming the system in both AWAY and STAY Modes.
TO USE FOR SYSTEM STATUS [Optional] ENROLL RF HOUSE ID CODE INTO MODULE
NOTE: The System Control Panel must be capable of transmitting system status, for example, an
L5000, L3000, or a VISTA Panel with a 5883 transceiver. Ensure the House ID is enabled in the
panel programming.
1.
Press (one second) and release the Program button; the LED will start flashing GREEN.
2.
IMMEDIATELY press (one second) and release the Program button again. The LED will start
flashing ORANGE.
3.
Disarm or Arm the control panel. The LED stops flashing ORANGE and then shows the status of
the control panel (see LED indications).
[Note: If no House ID code is enrolled, the enroll program mode times out after 2 minutes.]
LED STATUS
INDICATION
Flashing RED
Armed AWAY
Solid RED
Armed STAY
Solid GREEN
System READY
Flashing ORANGE
ALARM / Panic
4.
Test the status by arming and disarming the system in both AWAY and STAY Modes.
FCC / IC STATEMENT:
This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) This device may not cause harmful interference (2) This device must accept
any interference received, including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC et exempt de licence de norme(s) RSS d'Industrie Canada.
Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d'interférences nuisibles.
(2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une réception indésirable.
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright © 2012 Honeywell International Inc.
To Disable the
LED, remove the
Jumper next to
the LED.
To Disable the
LED, remove the
Jumper next to
the LED.
To Disable the
LED, remove the
Jumper next to
the LED.
To Disable the
LED, remove the
Jumper next to
the LED.
www.honeywell.com/security
Ê800-10947XŠ
P/N 800-10947 Rev A
3/12
Advertisement
