Performance Specifications; Qs0J65Bts2-8D - Mitsubishi Electric MELSEC QS SERIES User Manual

3
SPECIFICATIONS

3.2 Performance Specifications

Table3.2, 3.3, 3.4 show the performance specifications of safety remote I/O modules.

3.2.1 QS0J65BTS2-8D

Item
*2
No. of input points
Insulation method
Rated input voltage
Rated input current
Operating voltage range
Maximum number of simultaneous input
points
ON voltage/ON current
OFF voltage/OFF current
Input resistance
Input format
OFF ON
Response time
ON OFF
Safety remote station input response time
Voltage
External power Current
supply Protection function
Fuse
Wiring method for common
Number of occupied stations
Number of accesses to nonvolatile
memory inside module
Safety refresh response processing time
Voltage
Current
Module power
Protection function
*1
Fuse
supply
Momentary power
failure period
Noise immunity
Dielectric withstand voltage
Insulation resistance
Level of protection
Weight
Communication
section,
External module power supply
connection section
system External power supply
section,
input secton
Module mounting screw
*1: The power supply connected to the QS0J65BTS2-8D must satisfy the following conditions:
(1)Reinforced insulation
SELV (Safety Extra Low Voltage): Hazardous potential part (48V or more)
(2)Compliance with the LVD (Low Voltage Directive)
(3)Output voltage within 19.2V to 28.8VDC (Ripple ratio: 5% or less.)
*2: For the module with module technical version A, the number of input points is always 8. (The single input is not supported and two
input terminals are always used for each input.)
3
- 2 3.2 Performance Specifications
3.2.1 QS0J65BTS2-8D
Table3.2 Performance specifications of QS0J65BTS2-8D (1/2)
11.2ms or less + time of noise removal filter (1ms, 5ms, 10ms, 20ms, 50ms)
40mA (24VDC, all points ON, excluding the external load current)
External power supply overvoltage/overcurrent protection function
16 input points per common (Spring clamp terminal block 2-wire type)
Module power supply overvoltage/overcurrent protection function
Tested by a DC-type noise simulator with noise voltage of 500Vp-p, noise width of 1 s and frequency of 25 to
500VAC between all external DC terminals and ground, for 1 minute
10M
7-point two-piece terminal block [Transmission circuits, module power, FG]
M3 x 5.2 Tightening torque: 0.425 to 0.575N•m, 2 solderless terminals or less
Two-piece spring clamp terminal block [External power supply, input section]
M4 screw with plain washer finished round (Tightening torque range: 0.824 to 1.11N•m)
Mountable with a DIN rail (in 6 orientations)
DC input module
QS0J65BTS2-8D
8 points (double input), 16 points (single input)
Photocoupler
24 VDC
Approx.5.9mA
19.2 to 28.8VDC (Ripple ratio: 5% or less)
100%
15VDC/2mA or more
5VDC/0.5mA or less
Approx.4.3k
Negative common (source type)
0.4ms or less (at 24VDC)
0.4ms or less (at 24VDC)
19.2V to 28.8VDC (Ripple ratio: 5% or less)
8A (Not replaceable)
1 station
12
10 times
9.6ms
19.2V to 28.8VDC (Ripple ratio: 5% or less)
120mA or less (24VDC, all points ON)
0.8A (Not replaceable)
10ms or less
60Hz.
or more between all external DC terminals and ground,
by a 500VDC insulation resistance tester
IP2X
0.46kg