Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Honeywell ICON 100 SERIES
Summary of Contents for Honeywell ICON 100 SERIES
- Page 1 ICON-111S / ICON-111SR / ICON-112S ICON-112SR / ICON-132S / ICON-132SR ICON 100 SERIES REFRIGERATION CONTROLLER INSTALLATION GUIDE EN1B-0004UK07 R1003...
- Page 2 ICON 100 SERIES INSTALLATION GUIDE Trademark Information: ® Genus is a registered trademark of Honeywell Control Systems Ltd. EN1B-0004UK07 R1003...
-
Page 3: Table Of Contents
4.4 Electrical Wiring......................13 4.5 Applications in Critical Environments................13 4.6 Fitting ..........................14 4.7 Connections ........................15 For Icon 100 series operating instructions, please refer to document: MU2B-0001UK07. This can be found at Honeywell Cooling & Refrigeration’s internet site: www.honeywell.com/cooling EN1B-0004UK07 R1003... -
Page 4: Safety Instructions
ICON 100 SERIES INSTALLATION GUIDE 1. SAFETY INSTRUCTIONS Keep this instruction booklet where it can always be easily consulted by the operator or by maintenance personnel. Warning: hot components may be inside the plastic housing of the controller. No user-serviceable parts are inside the plastic housing of the controller. - Page 5 ICON 100 SERIES INSTALLATION GUIDE This controller is guaranteed by Honeywell to have a specific immunity level, in compliance with CE regulations, against irradiated and conducted electromagnetic disturbances. By irradiated electromagnetic disturbances we recommend to screen the controller with a metal screen connected to ground.
- Page 6 ICON 100 SERIES INSTALLATION GUIDE When the controller is used in appliances where any malfunction of said controller could cause a form of risk to persons, animals or things, ABSOLUTELY MANDATORY provide suitable protective/safety device, addition controller, which independently starts to operate in case of a failure.
-
Page 7: General Description
A Honeywell NTC 2k Ohm probe is supplied as standard with Icon and has a measuring range of –50 to +90 C. - Page 8 ICON 100 SERIES INSTALLATION GUIDE The Icon 100 Series have the following features. • display the measured case temperature as well as the alarm messages that refer to faulty cooling/refrigeration plant functions. • control the measured temperature through the thermostat probe in...
- Page 9 ICON 100 SERIES INSTALLATION GUIDE Product Description Part-No Icon 111S 1 relay, 1 probe. ICON-111S Icon 111SR 1 relay, 1 probe, real-time clock. ICON-111SR Icon 112S 1 relay, 2 probes. ICON-112S Icon 112SR 1 relay, 2 probes, real-time clock. ICON-112SR Icon 132S 3 relays, 2 probes.
-
Page 10: Technical Specification
ICON 100 SERIES INSTALLATION GUIDE 3. TECHNICAL SPECIFICATION Part Number Housing Self extinguishing PC/ABS Power Supply AC 230Vac ~ 4VA 50/60 Hz Display 3 digits, 14.2 mm high green LED's Resolution C or one unit Accuracy ± 0.7% t.s. Probe Type... - Page 11 ICON 100 SERIES INSTALLATION GUIDE Part Number Compressor Output SPDT relay AC 240V 6(3)A Defrost Output SPST relay AC 240V 6(4)A Fan Output SPST relay AC 250V 6(4)A Real Time Clock 24 Hour, 1 minute increment Network Type ® Honeywell Genus...
- Page 12 ICON 100 SERIES INSTALLATION GUIDE Part Number Operation Conditions Ambient Operating Temp: 0...+50 Ambient Storage Temp: -20...+80 Relative Humidity: +30…+85 NC Mount Type Panel mounted EN1B-0004UK07 R1003...
-
Page 13: Installation
ICON 100 SERIES INSTALLATION GUIDE 4. INSTALLATION 4.1 Introduction The controller must be installed in a place where it is protected from extre- me vibrations, impacts, water, corrosive gases, steam etc. and where tem- perature and humidity do not exceed the values given in the technical specification table (see page 11). -
Page 14: Electrical Wiring
ICON 100 SERIES INSTALLATION GUIDE 4.4 Electrical Wiring We would recommend protecting the controller power supply from electromagnetic disturbances, voltage peaks, etc. This can be easily done while wiring by following the instructions below: • separate the power supply cables of the compressor, motors, etc. -
Page 15: Fitting
ICON 100 SERIES INSTALLATION GUIDE 4.6 Fitting lcon is supplied in a panel-mount enclosure. While fitting the controller we recommend to leave enough room at the back in order to avoid compressing or excessively bending the cables. Overall instrument size and panel cut-out dimensions are given in Fig. -
Page 16: Connections
ICON 100 SERIES INSTALLATION GUIDE 4.7 Connections We recommend the use of wire gauges adequate for the given load power ratings in order to avoid damage to the screw connector. Fig. 2. ICON-111S/SR Models EN1B-0004UK07 R1003... - Page 17 ICON 100 SERIES INSTALLATION GUIDE Fig. 3. ICON-112S/SR Models EN1B-0004UK07 R1003...
- Page 18 ICON 100 SERIES INSTALLATION GUIDE Fig. 4. ICON-132S/SR Models EN1B-0004UK07 R1003...
- Page 20 Automation & Control Solutions Cooling & Refrigeration Newhouse Industrial Estate Motherwell North Lanarkshire, ML1 5SB Scotland, United Kingdom Phone: (44) 01698 481698 Fax: (44) 01698 481699 www.honeywell.com/cooling Subject to change without notice. Printed in United Kingdom EN1B-0004UK07 R1003...