Related Manuals for Honeywell CBU140
Summary of Contents for Honeywell CBU140
- Page 1 CBU140 Compact Booster Unit - single pump To ensure the quality of potable water according to EN1717 Instructions...
-
Page 2: Table Of Contents
6.5 Installing the pipelines ................10 6.5.1 Water connection ..............10 6.5.2 Pressure connection ..............10 6.5.3 Connecting the overflow ............10 6.6 Electrical connection ................10 6.6.1 Safety instructions ..............10 6.7 Verification of the waterflow ..............10 Honeywell GmbH Translation of original - EN1H-1377GE23 R1114... -
Page 3: Safety Guidelines
1.4 Unauthorised operation types The limits that are stated in the documentation have to always be complied with. The delivered system is only guaranteed to operate reliably when it is used as intended. EN1H-1377GE23 R1114 - Translation of original Honeywell GmbH... -
Page 4: Residual Dangers In Handling The Compact Booster Unit
Use of detergents Danger through contact with or breathing in dangerous fluids, ga- Wear personal safety equipment! ses, fumes, vapours or dust Pay attention to the safety specifications sheet of deter- gent manufacturers! Honeywell GmbH Translation of original - EN1H-1377GE23 R1114... -
Page 5: Consequences And Dangers That Result From Not Observing The Manual
Parts and special equipment not delivered by Honeywell are also not autho- Over and above this, special qualifications are required for the following rised by Honeywell for use. -
Page 6: General Information
Danger source In order to maintain the warranty, in the event of damage immediately Consequence of non-compliance contact the nearest Honeywell service centre. Avoidance 2.1 Conformity with the following norms 2.6 Other applicable documents Pump unit: Machinery Directive 2006/42/EG... -
Page 7: Description
Frequency max. pumping head Serial number max. power input Power output Protection class max. feed rate Key for the serial number Calendar year 2009 2010 2011 2012 2013 1st half-year 2nd half-year EN1H-1377GE23 R1114 - Translation of original Honeywell GmbH... -
Page 8: Version
A check valve in the pump control prevents back- flow. The pressure is read from a built-in pressure gauge. 4.1 Construction dimensions 200mm free space for service in both directions Figure 1: CBU140 Structure Pump control Pressure delivery Pump Tank Inlet tank... -
Page 9: Shipping
Danger 2. In the case of transport damage estimate the extent, document the Danger of injury from electric voltage. damage and notify Honeywell immediately in writing. High shock currents and burns from direct and indirect contact with 5.2 Transportation live parts. -
Page 10: Inspection Before Assembly
1. Install membrane pressure expansion vessel in consumption water line. Set pre-pressure to 3,2 - 3,4 bar. For filling use nitrogen only! 2. Connect the system to the consumption water line using the flexible pres- sure hose. Honeywell GmbH Translation of original - EN1H-1377GE23 R1114... -
Page 11: Start-Up
If not enough pump medium is fed into the system (the flow stalls), the pump control shuts down after 10 to 15 seconds. By pressing the Reset-key, the follow-up time can be reactivated. EN1H-1377GE23 R1114 - Translation of original Honeywell GmbH... -
Page 12: Maintenance
2. In case of leakage the floating ring seal must be replaced. 9.2 Overview of inspection tasks - The replacement should be performed by Honeywell technical staff. 9.3.5 Check preload pressure of membrane pressure expan- Interval... -
Page 13: Troubleshooting
Install an 8l - membrane pressure expansion vessel in the line ahead of the system inlet. With this container, severe pressure drops from thin lines are diminished and surges are contained without throttling the amount. Honeywell GmbH Translation of original - EN1H-1377GE23 R1114... -
Page 14: Shut-Down, Disassembly, Restart
Storage location closed room, dry and dust-free Ambient temperature 5°C to 40°C Relative air humidity max. 50% r.h. Compact Booster Unit / single pump CBU140 (from 2013 onwards) No. Description Part No. Float valve (complete) 18040893-CBU Pump incl. set of seal elements... -
Page 15: Start-Up Protocol
15. Start-up protocol The following Honeywell Compact Booster Unit was commissioned today by the signatories, authorised the Honeywell customer service staff, and this protocol was written. 1 Compact booster unit Series ..................Size ..................Serial number ..................Order number .................. -
Page 16: Declaration Of No Objection
The following safety precautions regarding rinsing medium, residual fluids and their disposal are required: .................................................................. We ensure that the above information is correct and complete and delivery will be made according to statutory requirements............................................City, date and signature Address Company stamp Honeywell GmbH Translation of original - EN1H-1377GE23 R1114... -
Page 17: Proof Of Maintenance
This compact booster unit is subject to the standards for drinking water and guidelines for maintenance therein. The unit has to be maintained regularly by qualified personnel and the results have to be documented. Date Operating company Name Signature EN1H-1377GE23 R1114 - Translation of original Honeywell GmbH... - Page 18 Honeywell GmbH Translation of original - EN1H-1377GE23 R1114...
- Page 19 EN1H-1377GE23 R1114 - Translation of original Honeywell GmbH...
- Page 20 Automation and Control Solutions Manufactured for and on behalf of the Environmental and Combustion Controls Division of Honeywell GmbH Honeywell Technologies Sàrl, Z.A. La Pièce 16, Hardhofweg 1180 Rolle, Switzerland by its Authorised Representative Honeywell GmbH 74821 MOSBACH MU1H-1377GE23 R1114...