Advertisement
OFF
COVER TAMPER (REED) SWITCH
REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED FOR DETAILS REGARDING
THE LIMITATIONS OFTHE ENTIRE ALARM SYSTEM.
FEDERAL COMMUNICATIONS COMMISSION STATEMENTS
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual.
Unauthorized changes or modifications could void the user's authority to operate the equipment.
CLASS B DIGITAL DEVICE STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for
your information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the
manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the
limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable
protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• If using an indoor antenna, have a quality outdoor antenna installed.
• Reorient the receiving antenna until interference is reduced or eliminated.
• Move the radio or television receiver away from the receiver/control.
• Move the antenna leads away from any wire runs to the receiver/control.
• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.
• Consult the dealer or an experienced radio/TV technician for help.
INDUSTRY CANADA CLASS B STATEMENT
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC / IC STATEMENT
This device complies with Part 15 of the FCC Rules, and RSS210 of Industry Canada. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may
cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est soumis aux
conditions suivantes: (1) Cet appareil ne doit pas causer d'interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y
compris les interférences causant une réception indésirable.
For the latest documentation and online support information, please go to:
For the latest warranty information, please go to:
www.honeywell.com/security/hsc/resources/wa
For patent information, see
N8909V5 1/17 Rev. A
DIP SWITCH SETTINGS
SWITCH
ON
NUMBER
0
1
2
3
4
5
6
ON — ON — ON — ON — ON — ON — ON — ON —
2
ON ON — — ON ON — — ON ON — — ON ON — —
3
4
ON ON ON ON — — — — ON ON ON ON — — — —
5
ON ON ON ON ON ON ON ON — — — — — — — —
ON ON ON ON ON ON ON ON
6
DIP SWITCH (WHITE AREAS DENOTE SWITCH HANDLES)
POSITION 7: NO FUNCTION
POSITIONS 2-6:
DETERMINE 4204'S ADDRESS: CONTROL'S INSTRUCTIONS SPECIFY ADDRESS
TO USE. "0" ADDRESS SETTING SHOWN (AS SHIPPED).
POSITION 1: ENABLES/DISABLES COVER TAMPER. ON = TAMPER DISABLED,
OFF = TAMPER ENABLED. SHOWN DISABLED AS SHIPPED.
4204
DIP SWITCH
FOR SETTING DEVICE ADDRESS
AND ENABLING/DISABLING TAMPER
4-PIN TOUCHPAD PLUG
EITHER OR BOTH
CAN BE USED
TB1
13
14
15
16
YEL
Must be connected to a
power-limited source.
BLK
Supervised
GRN
RED
SUPPORT & WARRANTY
https://mywebtech.honeywell.com/
www.honeywell.com/patents
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
©
Copyright
2008 Honeywell International Inc.
www.honeywell.com/security
4204 ADDRESS SETTINGS
("—" means "OFF")
8
9 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
7
ON — ON — ON — ON — ON — ON — ON — ON —
ON ON — — ON ON — — ON ON — — ON ON — —
ON ON ON ON — — — — ON ON ON ON — — — —
ON ON ON ON ON ON ON ON — — — — — — — —
ON ON ON ON ON ON ON ON
— — — — — — — —
RELAY
C
4
NC
TYPICAL
NO
(SHOWN "OFF")
C
RELAY
3
NC
NO
C
RELAY
2
NC
NO
C
RELAY
1
NC
NO
TB2
DATA IN FROM CONTROL
(–) GROUND
4204 CONNECTIONS
DATA OUT TO CONTROL
(+) 12VDC
MyWebTech
— — — — — — — —
4204-01-V1
If switching power
through a relay, the
power must be from a
power-limited source.
Relays are programmable
but outputs are not
supervised.
4204-02-V2
Patents
Warranty
Advertisement
