Table of Contents
Advertisement
Handle Installation (Fig. 24)
1. Remove the two lugs in the pushrod inserted into the
rack, and line up the hole on the pushrod with the hole
on the rack. Next, insert the pushrod into the rack from
the outside and then screw in the M8 flange bolt on
the inside and tighten down the bolt.
TORQUE: 17 - 22 lbf•ft (24 - 29 N•m, 2.4 - 3.0 kgf•m)
Wheel Kit Installation (Fig. 25)
1. Line up the hole on the roller with the hole on the rack,
insert the roller shaft into the rack from the outside,
and then screw in the M8 flange bolt on the inside and
tighten down the bolt.
TORQUE: 17 - 22 lbf•ft (24 - 29 N•m, 2.4 - 3.0 kgf•m)
Fit the front stand (Fig. 26)
1. Insert an M8×100 bolt into the holes on the rubber
blanket, front stand, and rack mounting plate.
2. Screw the M8 flange bolt onto the M8×100 bolt from
the mounting plate and then tighten down the bolt.
Stopping the engine with remote control
1. Press the stop button.
2. Turn the engine switch on the generator to the
"O (OFF)" position.
3. Turn the fuel valve lever on the generator to the
"O (OFF)" position.
Battery Tray (Fig. 27)
NOTE:
Battery is not included. Use a battery (rating: 12V-10Ah,
L x W x H: maximum 160 mm x 90 mm x 160 mm)
available in the market.
1. Connect the black power line (ground electrode) on
the electric generator to the negative electrode on the
battery and the red power line to the positive electrode
on the battery.
2. Place the battery connected to the power lines into the
battery box on the rack.
3. Hang each of the two card buckles on the rubber belt
onto one of the two hangers on the battery box.
WARNING:
Lead and lead compounds are used in battery posts,
terminals, and related accessories. Always wash
hands after handling.
Engine Oil (Fig. 13)
The generator is shipped WITHOUT OIL in the engine.
Place the generator on a stable and level surface. Add
enough of the recommended oil to bring the oil level to the
top of the oil filler neck.
Use a 4-stroke motor oil that satisfies the requirements for
API service category SJ or later (or equivalent).
Do not overfill the engine with oil. If the engine is
overfilled, the excess oil may get transferred to the air
cleaner housing and air filter.
WARRANTY SERVICE
INFORMATION
CUSTOMER SERVICE INFORMATION
The personnel at the servicing dealership are trained
professionals. They should be able to answer most
20
questions you may have. If there is a problem that your
dealer does not solve to your satisfaction, please discuss
it with the Service Manager or General Manager of the
dealership. Almost all problems are solved in this way.
If you are dissatisfied with the decision made by the
dealership's management, contact the Makita
Corporation.
For European countries only
EC Declaration of Conformity
We Makita Corporation as the responsible
manufacturer declare that the following Makita
machine(s):
Designation of Machine: Petrol Generator
Model No./ Type: EG2250A, EG2850A, EG4550A,
EG5550A, EG6050A
Specifications: see "SPECIFICATIONS" table.
are of series production and
Conforms to the following European Directives:
2000/14/EC, 2004/108/EC, 2006/42/EC,
2006/95/EC
And are manufactured in accordance with the following
standards or standardised documents:
EN12601, EN55012, EN61000, EN60204-1
The technical documentation is kept by:
Makita International Europe Ltd.
Technical Department,
Michigan Drive, Tongwell,
Milton Keynes, Bucks MK15 8JD, England
The conformity assessment procedure required by
Directive 2000/14/EC was in Accordance with annex VI.
Notified Body:
AV TECHNOLOGY LTD
AVTECH House,Arkle Avenue
Stanley Green Trading Estate
Handforth,Cheshire
SK9 3RW,United Kingdom
Identification number 1067
Model EG2250A
Measured Sound Power Level: 94 dB (A)
Guaranteed Sound Power Level: 95 dB (A)
Model EG2850A, EG4550A, EG5550A, EG6050A
Measured Sound Power Level: 95 dB (A)
Guaranteed Sound Power Level: 96 dB (A)
27.12.2013
Tomoyasu Kato
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, 446-8502, JAPAN
Director
Hide quick links:
Advertisement
Table of Contents
