Casio 2165 General Manual

Module No. 2165
• If the contents of the display seem to be continually changing, see "AUTO DISPLAY FUNCTION" for information on how to stop it.
• Press C C C C C to change from mode to mode.
• In any mode, press L L L L L to illuminate the display for about 3 seconds.

Timekeeping Mode

Day of The
Week Display
Press B B B B B .
TIMEKEEPING MODE
• In the Timekeeping Mode, press D D D D D to switch between
Month - Day
Day of week
• Press L L L L L in the Timekeeping Mode to activate the EL
• The Timekeeping Mode has two displays. One shows
FRI
• There are three different time graph formats, which
Hour
Seconds
Minutes
PM indicator
No Alarm Time Setting for Current Date
Month - Day
Time graph

Alarm Time Setting for Current Date

Appointment icon
An appointment icon appears on the display and the time
graph hour for which the alarm is set flashes. The time
Time graph
graph shows how long before the alarm time will be
Appointment
reached.
time indicator
Month - Day

Alarm Time Setting Within the Hour

Appointment icon
One hour before an alarm time is reached, a tone sounds
and the time graph format changes, replacing the month
Time graph
and day with a countdown of the minutes and seconds
Appointment
left until the alarm time is reached.
time indicator
Remaining minutes and seconds
To set the time and date
1. Hold down A A A A A while in the Timekeeping Mode. The seconds digits flash on the
display because they are selected .
2. Press C C C C C to change the selection in the following sequence.
Seconds
Animated Graphic
3. While the seconds digits are selected (flashing), press D D D D D to reset the seconds to
00. If you press D D D D D while the seconds count is in the range of 30 to 59, the seconds
are reset to 00 and 1 is added to the minutes. If the seconds count is in the range
of 00 to 29, the minutes count is unchanged.
4. While any other digits (besides seconds) are selected (flashing), press D D D D D to in-
crease the number or B B B B B to decrease it. Holding down either button changes the
current selection at high speed.
• While the animated graphic is flashing, you can select one of the following graph-
ics. The animated graphic you select appears on the display whenever you turn on
the EL backlight in the Timekeeping Mode.
1. Random selection of 2, 3, or 4.
2. LOVERS A
3. LOVERS B
4. LOVERS C
Telememo Mode
Time Graph
Display
the 12-hour and 24-hour formats.
backlight and to display animated graphics.
the Mark along with the current day of the week. The
other display shows a time graph for the current date.
Pressing B B B B B switches between the two displays.
change automatically in accordance with the current re-
lationship between an alarm time setting and the cur-
rent time.
Hour Minutes Year
Month
Day

GENERAL GUIDE

Alarm Mode
5. After you set the time and date, press A A A A A to return to the Timekeeping Mode.
• The day of week is automatically set in accordance with the date.
• The date can be set within the range of January 1, 1995 to December 31, 2039.
• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Timekeeping Mode automatically.
About the backlight
In any mode, press L L L L L to illuminate the display for about 3 seconds.
• The backlight of the watch employs an electro-luminescent (EL) light, which loses
illuminating power after very long use.
• The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.
• The watch will emit an audible sound whenever the display is illuminated. This is
caused by a transistor that vibrates when the EL panel lights up. It does not indi-
cate malfunction of the watch.
• The backlight automatically turns off whenever an alarm sounds.
The following causes all data stored in memory to be deleted. Be sure to
always keep separate written copies of all important data.
Malfunction or repairs/Dead battery/Battery replacement
In no event will CASIO be liable for loss of data or any damages arising out of
such loss.
Mode indicator
Remaining
memory
Name
Telephone
number
[New Data Display]
Text area
¢
Number area
3. Use D D D D D or B B B B B to input a character at the cursor position. The character changes in
the following sequence. Holding down either button changes the character at high
speed.
Press .
(Space)
Press .
4. After you select the character you want, press C C C C C to advance the cursor to the right.
• Repeat 3 and 4 until you complete name input.
• You can input up to 8 characters in the name area.
5. After the name input is through, use C C C C C to move the cursor to the telephone number
area.
6. While the cursor is in the telephone number area, use B B B B B or D D D D D to input a number
you want. The character changes in the following sequence. Holding down either
button changes the character at high speed.
Press .
Press .
7. After you select the character you want, press C C C C C to advance the cursor to the right.
• Repeat 6 and 7 until you complete number input.
8. After you input the telephone number you want, use C C C C C to move the cursor to the
cell phone number area.
• The
indicator indicates the cell phone display.
• Input the cell phone number using the same procedure as you did for the telephone
number.
• If you don't want to input a cell phone number, proceed from step 9 without input-
ting anything.
Stopwatch Mode
TELEMEMO MODE
Caution
The Telememo Mode lets you store up to
20 pages of name, telephone number, and
cell phone (or pager) number data. You can
recall data by scrolling through it on the dis-
play.
• The number of unused pages still availa-
ble for storage of data appears on the dis-
play every time you enter the Telememo
Mode.
• You can input up to eight characters in
C
the text area, and 12 digits in each of the
two (telephone and cell phone) number
areas.
• The data item on the display when you
exit the Telememo Mode appears first the
next time you enter the Telememo Mode.
To input new Telememo data
1. In the Telememo Mode, press D D D D D or B B B B B until the New
data display appears.
• The new data display is the one that is blank (contains
no name and telephone number).
• If there is no Telememo data stored in memory yet, the
new data display appears as soon as you enter the Tele-
memo Mode.
• If the message "
" appears on the display, it
means that memory is full. To store more data, you will
first have to delete some of the data.
2. Hold down A A A A A and a cursor appears in the text area.
A to Z 0 to 9
– (Hyphen) 0 to 9
2165-1
(Space)