Makita DUM604 Instruction Manual
Cordless
Hide thumbs
Also See for DUM604:
- Instruction manual (133 pages) ,
- Instruction manual (108 pages) ,
- Instruction manual (18 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita DUM604
Summary of Contents for Makita DUM604
- Page 1 INSTRUCTION MANUAL Cordless Grass Shear DUM604 Read before use.
-
Page 2: Specifications
Symbols WARNING: Wear ear protection. ment. Be sure that you understand their meaning before use. DUM604 with shear blade for hedge trimmer installed Sound pressure level (L Read instruction manual. WARNING: Wear ear protection. Vibration Keep bystanders away. -
Page 3: Safety Warnings
Prevent unintentional starting. Ensure the SAFETY WARNINGS switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with General power tool safety warnings that have the switch on invites accidents. WARNING: Remove any adjusting key or wrench before turning Read all safety warnings and all... - Page 4 Under abusive conditions, liquid may be Before use always check that the equipment ejected from the battery; avoid contact. If con- is safe for operation. Check the security of the cutting tool and the guard and the switch trig- liquid contacts eyes, additionally seek medical ger/lever for easy and proper action.
- Page 5 13. Always ensure that the ventilation openings are kept clear of debris. ence of alcohol, drugs or medication. 14. Cutting means continues to run after the motor Work gloves of stout leather are part of the is switched off. basic equipment of the hedge trimmer and must always be worn when working with it.
-
Page 6: Functional Description
Only use genuine Makita batteries. have been altered, may result in the battery bursting 1. Red indicator 2. Button 3. Battery cartridge also void the Makita warranty for the Makita tool and charger. while sliding the button on the front of the cartridge. - Page 7 Never use the tool if it starts when you pull the switch trigger without pressing the lock-off button. light up for few seconds. Makita Service Center for repairs. Indicator lamps Remaining capacity WARNING: Never disable the lock function or tape down the lock-off button.
- Page 8 moving it in the direction of the arrow. 1. Indicator lamp Lamp status and action to be taken Indicator lamp Status NOTE: Charge the battery. actual shearing height may vary depending on the red. battery capacity condition of the lawn or the ground. is low.
- Page 9 1. Hinge 2. Grass receiver the grooves on the tool by sliding the grass receiver toward the front of the tool and moving it in the direction of the arrow. Installing or removing the grass receiver CAUTION: When installing or removing the NOTICE: Do not attach the hinge of the grass grass receiver, be sure to attach the blade cover...
- Page 10 Remove the undercover, shear blades, and crank. the alignment line. and large rounds facing up. 2. Shear blades 3. Crank Installing the shear blades blades. 1. Crank in the base plate and the two protrusions on the blades are lined up. 1.
- Page 11 the undercover. securely in place. 1. Lock lever CAUTION: Never use the tool without install- on the under- ing the undercover. cover is aligned with on the lock lever. 10. Remove the blade cover, and then turn on the tool to check that it works properly.
- Page 12 While pressing the lock lever, turn the undercover counterclockwise until on the undercover is aligned with on the lock lever. 1. Screws NOTE: removing the screws. Remove the crank from the shear blades. Remove the undercover. 1. Crank NOTE: NOTE: to the removed shear blades, and then store the blades.
- Page 13 shear blades. Insert the claw of the base plate into the the alignment line. groove on the tool. Make sure that the shear blades are 1. Claw large rounds facing down. 1. Crank 1. Screws Slide the shear blades so that the hole on the base plate is positioned at the center of the rings of blades.
-
Page 14: Operation
Installing or removing the chip receiver Optional accessory CAUTION: When installing or removing the chip receiver, always wear gloves and attach the blade cover so that your hands and face do not directly contact the blade. clean-up afterward much easier. It can be installed on either side of the tool. - Page 15 WARNING: Keep hands away from blades. cutters before using this tool. NOTICE: Do not use the tool in a way that causes CAUTION: Avoid operating the tool in very the motor to stop or to rotate extremely slowly. hot weather as much as practicable. When operat- ing the tool, be careful of your physical condition.
-
Page 16: Maintenance
MAINTENANCE CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. Centers, always using Makita replacement parts. 16 ENGLISH... - Page 17 Cleaning the tool Clean the tool by wiping off dust with a dry cloth or one dipped in soapy water and wrung out. NOTICE: Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result. Blade maintenance Before the operation or once per hour during operation, apply low-viscosity oil (machine oil, or spray-type lubri- cating oil) to the blades.
-
Page 18: Optional Accessories
OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool accessories or attachments might present a risk of for its stated purpose. If you need any assistance for more details regard- ing these accessories, ask your local Makita Service Center. - Page 20 Jan-Baptist Vinkstraat 2, Makita Europe N.V. 3070 Kortenberg, Belgium 3-11-8, Sumiyoshi-cho, Makita Corporation Anjo, Aichi 446-8502 Japan 885551-228 www.makita.com 20161022...